USER MANUAL PROTON POWER CONTROL PVT. LTD., PUNE 3P VFR Salient Features: 1] Microcontroller based technology. 2] Protection against under voltage, Over voltage, Over Frequency, Under Frequency, Single Phasing & Reverse Phasing 3] All the set points settable by keys. 4] Trip Delay for Under voltage & Unbalance is settable 5] Reverse Phasing Protection can be bypass through settings. 6] Indications for Low voltage, High Voltage, SPP & Relay ON. 7] Message Display for SPP, Reverse Phasing & Unbalance Faults. 8] No separate auxiliary supply required. NOTE: Hold feature: - Press & release Upward Arrow key to hold the display to view particular Parameter To release HOLD press & release Upward Arrow key once. Parameter Settings: Parameter Under Voltage Over Voltage Over Frequency Under Frequency Unbalance Setting Trip Time delay for UV & UB Trip Time delay OV SPP& REVP Relay ON/RESET Delay Default 300 V 460 V 52Hz 48Hz 70 V 5 sec < 100 msec. 10 sec Range 300 V to 380 V 430 V to 500 V 51Hz to 60Hz 0Hz to 49Hz 1 V to 100 V 1 to 60 seconds - Hysteresis 10 V 10 V 1Hz 1Hz 10 V - 1 to 60 sec. - Technical Specifications: 1] Supply voltage: 3 Phase 415 VAC, 50 Hz (R, Y, B &N) (No auxiliary supply) 2] Output Contacts: Two SPDT (C-N/O-N/C) Relay, Rating 5A at 250V AC 3] Indications: FAULT (UB/SPP/REVP, UV, OV, UF, OF): RED LED, RELAY ON: GREEN LED 4] Keys: 1) SET: SET key, Press to enter into SET Mode 2) INC: Upward Arrow key, Press to increment the setpoint. 3) DEC: Downward Arrow key, To Decrement the setpoint. 5] Operating Temperature range: -5 C to 60 C. 6] Relative Humidity: 10 to 95% RH 7] Mounting: Flush 8] Dimensions: 96 X 96 mm. Working: 1] If the Input supply is within the range of the fault limits then On Timer starts decrementing on display & after Set On Time over Relay will be ON with RLY indication glowing. 2] If OV, UV, OF, UF, Spp/Reverse phasing/Unbalance occurs in the supply then Relay will be OFF after the trip delay of that particular fault & fault LED starts blinking. 3] If any Phase to Phase Voltage increases above OV set point, Relay will trip after trip delay (<100 ms) over. If that particular phase to phase voltage reduces below (OV set point - 10 V), Relay will be ON after the set reset delay over. 4] If any Phase to Phase Voltage increases/reduces above/below the UB set point compared to other two Phase to Phase voltages, Relay will trip after set trip delay over. If that particular phase to phase voltage reduces/increases below/above (UB set point -/+ 10 V), Relay will be ON after the set reset delay over. If the frequency reduces below UF or increases above OF then the relay will trip. Hysteresis is 1HZ. TM PROTON 5] If any of the Phase fails, Relay will trip after trip delay (<100 ms) over. If all phases are present, Relay will be ON after the set reset delay over. 6] If Phase sequence is changed to R-B-Y/Y-R-B/B-R-Y, Relay will trip after trip delay (<100 ms) over. If phase sequence is corrected to R-Y-B, Relay will be ON after the set reset delay over. UB/SPP/REVP, UV, OV, UF, OF. PROTON POWER CONTROL PVT.LTD. S.NO.28 JAGTAP DAIRY, PIMPLE NILAKH PUNE-411027. TEL: 020-27270800, 27276777. TEL/FAX: 020-27270100 MOBILE: 9764885010/9422009655 E-MAIL: [email protected] [email protected] -