TH PIR - Bondor Insulated Panel Systems

TH
Technical Data Sheet
PIR
BON0126 Bondor Tech Data Sheets. Current as of: 21/08/14
Product Description
MetecnoSpanTH® offers a new standard in PIR roofing and wall cladding, combining
cost savings with a high performance, non-ozone depleting PIR insulated option.
MetecnoSpanTH® roof skin is made from COLORBOND® or Zincalume™ steel, a fireretardant PIR core and a bright silver or white foil underside, making this both a clean
and serviceable roofing product. MetecnoSpanTH® cuts the costs by outperforming
traditional roofing with a wider cover, faster installation time and higher thermal
efficiency and acoustic properties.
Panel Properties
Panel Thickness (mm)
40
60
80
100
5.33
6.10
6.86
7.62
‘U’ Value (W/m2K)
0.44
0.31
0.24
0.19
‘R’ Value (m K/W)
2.30
3.20
4.20
5.10
Mass (kg/m )
2
Thermal Performance
2
Span Table
Non-Cyclonic Wind Category (Roof Applications)
Single Span
Span (mm) for maximum uniformly distributed ULS design wind load (kPa)
Wind Category
Core
PIR (Fire-retardant Polyisocyanurate)
Width (cover mm)
1000
Thickness (mm)
40, 60, 80, 100
Length
Up to 16m (check for availability)
Single Span
End Span
Internal Span
W33N (N2)
1500
1500
1500
Exterior Facing Skin
0.42mm G550 Zincalume™
or COLORBOND® steel
W41N (N3)
1500
1500
1500
Interior Facing Skin
Silver foil or white foil
W50N (N4)
1100
900
1100
Exterior Facing Colour
Surfmist®, Paperbark®,
Classic Cream®, Pale Eucalypt®,
Headland®, Dune®, Shale Grey®,
Zincalume®
Recommended Uses
Air conditioned offices, supermarkets, agricultural buildings, industrial buildings,
warehouses, commercial buildings, domestic re-roofing.
Standard Colours
Interior Facing Colour
Silver foil or white foil
Finishes
Plain
Recommended Pitch
2 degrees minimum
Fire Hazard Properties - AS1530.3 indices
Ignitability Index
0
Spread of Flame Index
0
Heat Evolved Index
0
Smoke Index
1
Under certain construction applications, MetecnoSpanTH can achieve FM Approval. Refer your
local Bondor® branch.
NOTES:
1. F ixing with 14g tek screws (or equivalent) at each rib are required.
2. P ressures specified are for wind gusts only per AS1170. Assumed wind co-efficients for
determining C fig: Cpe = -0.9, Cpi = +0.2, Kl = 1.5.
3. D
eflection limit of span/150 applies, and in accordance with Serviceability Limit State
criteria per AS1170.0 – TABLE C1.
4. S elf weight of the panel has been allowed for, plus an allowance of up to 10kg/m2 for light
duty fittings (lights, etc.). No other dead loads permitted.
5. N
on-trafficable maintenance access (concentrated load) of 110kg on any one panel has
been allowed for (as per min. requirements of AS/NZS 1170.1:2002).
6. D
istributed live load of 0.25kPa has been allowed for (as per AS/NZS 1170.1:2001).
Bondor® tests comply with details outlined in AS 4040, AS 1562 and as 1170.
7. This span table applies to non-cyclonic regions only.
8. Min. roof slope of 2 degree applies.
TH
Technical Data Sheet
PIR
BON0126 Bondor Tech Data Sheets. Current as of: 21/08/14
Joint
Ceiling side silver foil or white foil
Profiles
Plain
Dimensions
20mm
333mm
292mm
38mm
41mm
1000mm cover width
Thickness
Bondor® National Network
BRISBANE / EXPORT
103 Ingram Road
Acacia Ridge QLD 4110
T: 07 3323 8500
F: 07 3323 8501
MELBOURNE
329A St Albans Road
Sunshine VIC 3020
T: 03 8326 8000
F: 03 8326 8099
SYDNEY
49 – 53 Newton Road
Wetherill Park NSW 2164
T: 02 9609 0888
PERTH
17 Gauge Circuit
Canning Vale WA 6155
T: 08 9256 0600
F: 08 9256 0620
ADELAIDE
70 – 72 Rundle Road
Salisbury South SA 5106
T: 08 8282 5000
F: 08 8282 5099
LAUNCESTON
7 Connector Park Drive
Kings Meadows TAS 7249
T: 03 6335 8500
F: 03 6335 8544
F: 02 9729 1114
To connect to your nearest Bondor® branch simply call 1300 300 099 or visit www.bondor.com.au
Metecno Pty Limited. ABN 44 096 402 934. The manufacturer reserves the right to change the specification without notice. Bondor®,
Equitilt®, BondorPanel®, FlameGuard®, MetecnoPanel®, InsulWall®, SolarSpan®, MetecnoSpan®, Purline®, Equideck®, InsulLiving®, Metecno,
MetecnoSpanTH & MetecnoPanelTH are trademarks of Metecno Pty Limited. BlueScope, COLORBOND®, Permagard® and colour names are
trademarks of BlueScope Steel Limited. Microban® is a registered trade mark of the Microban Products Company. The colours shown in this
publication have been reproduced to represent actual product colours as accurately as possible. However, given printing limitations,
we recommend checking your chosen colour against an actual sample before placing orders. This advice is of a general nature only.
Designers must provide for adequate structural performance and other Building Code requirements. This information is subject to change.
Refer to Bondor® website for latest version. Consult Bondor® for your application.
Leaders in Thermal & Architectural Building Solutions

Download Report