BOLIDT COATING 24039 Composition BOLIDT COATING 24039 consists of 2 components, based on waterborne polyurethane emulsions, which have to be mixed into a perfectly homogeneous mass shortly before use. Application The principal application of BOLIDT COATING 24039 is the coating of synthetic floors, wood, polyester panels, etc., by which the surface obtains a dust, scratch and wear resistant transparent coating. Properties BOLIDT COATING 24039 is usually applied in two layers, thus hardly influencing the structure of the substrate. Technical properties (measured at 20° C) Specific gravity Consumption Shrinkage after curing Viscosity Skid Resistance Leroux dry wet Taber Abraser: Impact resistance Temperature durable Solids (% by Volume) VOC (% by Volume) : approx. 1,1 kg/dm3 depending on colour : 6 - 7 m2/kg : none : approx. 200 mPa.s at 22 °C. : approx. 99 : approx. 35 : approx. 30 mg : good : from -30 °C. till 60 °C (no shock loading) : approx. 35% : approx. 5% Adhesion BOLIDT COATING 24039 has excellent adhesion to polyurethane and epoxy based synthetic floors. Substrates must be clean and dry (see also “substrates”). Appearance After curing the BOLIDT COATING 24039 has a dull appearance. The surface is smooth. BOLIDT COATING 24039 is available in many NCS-colours. See also the Bolidt Colour Manager on our Site www.bolidt.com. Thickness BOLIDT COATING 24039 is to be evenly applied in 1 - 2 layers of 150 gr/m2. Total dry film thickness is approx. 50 micrometer per layer. L2.4039.03/PdR/0603/RdJ/acc. 1/3 Our advice with respect to the technical application, either verbal or in writing or by means of tests, is given to the best of our knowledge, however, is only an indication without engagement, also regarding possible rights of third parties. They do not take away the necessity of testing the products delivered for their suitability to intented use and purpose. Application, use and working up of the products take place beyond our control and therefore are your responsibility. It goes without saying we guarantee the good quality of our products. Entered in the Register of the Chamber of Commerce and Industry at Dordrecht under no. 23035272. All our contracts, offers, deliveries and executions are made in accordance with our General Conditions, filed at the Registry of the district Court at Dordrecht. Bolidt Kunststoftoepassing B.V. Nijverheidsweg 37 P.O.Box 131 3340 AC Hendrik-Ido-Ambacht The Netherlands T F E I +31 (0)78 684 54 44 +31 (0)78 684 54 00 [email protected] www.bolidt.com Mixing ratio 91 parts by weight BOLIDT COATING 24039 Component A 9 parts by weight BOLIDT COATING 24039 Component B Pot life As a mixture: at 10°C - approx. 3 hours at 15°C - approx. 3 hours at 20°C - approx.2 ½ hours at 30°C - approx.1 ½ hours Mixing procedure Mixing is to be done mechanically using slow running mixer. First to stir Component A thoroughly, before adding Component B. Mix thoroughly (for 3 min.). Pour the mixture in a clean drum, and mix well again. An intensive mixing of the Components A and B is essential. ADD NO WATER, NOR ADD SOLVENTS!! Leave the mixture at rest for 10 min. before applying the material (induction time). Neglecting this induction time will result in uneven gloss after curing. CAUTION: Take care that no solid coating film drops into the material from the lid. Application BOLIDT COATING 24039 can be applied by lambs roller. Spread the material evenly over the surface area. Apply any the second layer (if necessary) after the first is completely cured, usually this is after 24 hours, but within 5 days. When the second layer is to be applied after more than 5 days, first grind the first layer well. Material is to be applied at temperatures ranging from 10 to 30°C, and a relative humidity of the air less than 80%. Curing After 24 hours at 15 °C the BOLIDT COATING 24039 is well enough cured for foot traffic, and after 48 hours the BOLIDT COATING 24039 can be fully charged. Complete chemical curing has taken place after 7 days (at 20°C). Substrate All substrates must be at least at 8°C, and at least 3°C above the dew point temperature for proper adhesion. Synthetic floors These substrates (surface smooth and sealed) must be fully cured and maximum 3 days old. Substrates must be completely dry, clean and free of grease. Substrates older than 3 days must be grinded first. Remove all dust before applying BOLIDT COATING 24039. L2.4039.03/PdR/0603/RdJ/acc. 2/3 Our advice with respect to the technical application, either verbal or in writing or by means of tests, is given to the best of our knowledge, however, is only an indication without engagement, also regarding possible rights of third parties. They do not take away the necessity of testing the products delivered for their suitability to intented use and purpose. Application, use and working up of the products take place beyond our control and therefore are your responsibility. It goes without saying we guarantee the good quality of our products. Entered in the Register of the Chamber of Commerce and Industry at Dordrecht under no. 23035272. All our contracts, offers, deliveries and executions are made in accordance with our General Conditions, filed at the Registry of the district Court at Dordrecht. Bolidt Kunststoftoepassing B.V. Nijverheidsweg 37 P.O.Box 131 3340 AC Hendrik-Ido-Ambacht The Netherlands T F E I +31 (0)78 684 54 44 +31 (0)78 684 54 00 [email protected] www.bolidt.com Other substrates Please ask for the advise of the Bolidt laboratory. Precautions To prevent the skin from getting irritated it is recommended to use protective hand creams and/or gloves. Take care of proper ventilation during the work. Tools Tools are to be cleaned with clean tap water before curing takes place. Package BOLIDT COATING 24039 can be delivered in sets of 5 kg. It is recommended to store the BOLIDT COATING 24039 dry and in closed pails at a temperature of preferably 15°C. Shelf life min. 6 months in original packaging. KEEP FROM FREEZING. L2.4039.03/PdR/0603/RdJ/acc. 3/3 Our advice with respect to the technical application, either verbal or in writing or by means of tests, is given to the best of our knowledge, however, is only an indication without engagement, also regarding possible rights of third parties. They do not take away the necessity of testing the products delivered for their suitability to intented use and purpose. Application, use and working up of the products take place beyond our control and therefore are your responsibility. It goes without saying we guarantee the good quality of our products. Entered in the Register of the Chamber of Commerce and Industry at Dordrecht under no. 23035272. All our contracts, offers, deliveries and executions are made in accordance with our General Conditions, filed at the Registry of the district Court at Dordrecht. Bolidt Kunststoftoepassing B.V. Nijverheidsweg 37 P.O.Box 131 3340 AC Hendrik-Ido-Ambacht The Netherlands T F E I +31 (0)78 684 54 44 +31 (0)78 684 54 00 [email protected] www.bolidt.com
© Copyright 2025 ExpyDoc
