MakerLED Quick Start Guides - Driver and Controller.ai

Part: MakersCTR1.02
MakersLED
MakersCONTROLLER
TM
Part: MakersDRV1.2
MakersLED
TM
MakersDRIVER
TM
Quick Start Guide
Incorrect Power Polarity Will
Blow the Fuse!
Power off before making connections!
• 1x Green Jack: Power, 48V DC input
• 2x Blue Jacks: 2 LED Channels, Connect LEDs
• 1x Black Jack: 0-10V Lighting Control Input
• 2x Audio-Style Jack: MakersCONTROLLER control
Includes: MakersDRIVER, Mounting Hardware, Cable
• 1x White 3 Pin Connector: One 12V DC fan
“1”
tie (to secure fan cable) & jumper
1. Prepare the 48V Power Supply (PSU)
Confirm the line voltage switch (110v/220v), confirm
the DC output Voltage. See your PSU
manual.
INPUT
SIDE
Also labeled as
“INPUT” on the
underside of
MakersDRIVER
Install LDD
Drivers
Includes: MakerCONTROLLER,
2 Audio-Style Jumper Cables
2. Install Meanwell LDD Drivers into
CH1DRIVER and CH2DRIVER sockets
Notice one corner has 3 pins instead of 2. Visually align
all the pins in the sockets and push squarely.
Quick Start Guide
1. Install MakersDRIVER according to users manual. Apply 48V power.
2. Install MakersCONTROLLER: Plug the tethered audio-style cable into the MakersDRIVER input labeled
"INPUT" jack on the MakersDRIVER.
3. Test it! Minimize variables by attaching only one LED on each
channel to start. Once you see it’s working add more LEDs.
How Many LEDs on each Blue Jack?
Given 48v DC input, the MakersDRIVER can drive up to 45V of LEDs
#LEDs = 45V/LED Voltage (see vendor product page for LED voltage)
For multiple MakersDRIVERS, use the included cables to daisy chain the output to proceeding input
connections on MakersDRIVERs. Optionally, install the jumper onto “CH3&4” pins of the MakersDRIVER to
make the default CH1&2 become CH3&4 to the MakersCONTROLLER.
Note: If the Input/Output connections are not correct, the
MakersCONTROLLER will not power and/or will not pass data to proceeding MakersDRIVERS.
MakersLED Heatsink
Screw
Side MountingTab
Mounting
Tabs
Safety & Disclaimer: You are the builder and you are responsible for
all aspects of safety on your build. Static Electricity: Discharge yourself
before handling electronics. Salt Spray: Do not allow water splash or
salt spray to come into contact with the MakersDRIVER.
Get the Full MakersDRIVER Manual at:
12:00:00P
%:
www.MakersLED.com/support
10
20
DAY
30
40
50
Control Knob
2X16 Character
LCD Display
-Turn to Scroll
-Push to Select
Data Cable
to MakersDRIVER
Get the Manual at: www.MakersLED.com/support
Safety & Disclaimer: You are the builder and you are responsible for all aspects of safety on your
build. Static Electricity: Discharge yourself before handling electronics. Salt Spray: Do not allow
water splash or salt spray to come into contact with the MakersDRIVER/CONTROLLER.
MidDay
Intensity %
Noon Peak (On/Off )
~28 Day Lunar Cycle
(On/Off )
CH5
CH3
CH2
Cloudcover (On/Off )
et
CH4
Set/rise Length
(minutes)
... Night % CH1
Time
s
Sun
Sun
rise
Day %
Set/rise Length
(minutes)
Night %...
MAIN SCREEN:
12:00:00P
%:10
20
DAY
30
40
50
Half
Moon
No
(Push)
ENTER
NO/YES
1)
Set
Current
Time
&
Set
Times
Scroll
3)
Day
Cloud
Cover
4)
CH
#:
Set/rise
01
CH1:
Day
100%
Sunrise
CH1:
CH2:
Night
Day
CH2:
Cover:
6)
Lightning
Thunderstorm
01
7)
Start
Demo/Preview
Auto
CH3:
Day
Night
Noon
CH3:
Peak:
#:
Lightning
Freq:
Start
25%
high performance DIY LED systems
© MakersLED
8)
(Push)
<-Save
&
Exit
Demo
Mode:
Storm
%:90
12:00P
80
85
Day
60
95
Day
CH5:
Night
CH5:
5%
Cyle:
Yes/No
DEMO
Scroll
CH4:
Show
NO/YES
tm
Scroll/Knob
Night
Lunar
Start:
100%
5%
NO/YES
CH
CH4:
100%
5%
NO/YES
Sunset
7:00P
100%
5%
Cloud
Start:
7:00A
100%
5%
Extras
Length:
30m
Night
Intensity
5)
MakersLED
Noon
Peak
Time:
Day
Intensity
Night
New
Moon
12:00P
Select
2)
Rise
Half
Moon
Channel 1 through 5
Percentage Intensity
Yes
Set
Full
Moon
CONFIG?
Info
Menus?
NO/YES
Now?

Download Report