② LZ□T-A1 19.6kN∼ 58.8kN LZ□T-A2 98.0kN∼ 245kN 共通仕様 SPECIFICATIONS 形 式 TYPE SPECIFICATION 耐 圧 Proof pressure 最高使用圧力 Maximum working pressure MPa 36.8 MPa 24.5 最大クランプ力 kN 19.6 39.2 58.8 98.0 157 245 Maximum clamping force スト ロ ー ク Stroke 締 め Stroke 代 (mm) 6 7 7 8 8 8 (mm) 2.5 2.5 2.5 3 3 3 3.5 4.5 4.5 5 5 5 アンクランプストローク (mm) Unclamp Stroke 所 要 油 量 構 造 Required volume of oil (m ) 6.0 13.8 19.9 41.0 66.3 102 (℃) ー5∼60 使用温度範囲 CONSTRUCTION 使 用 油 単動バネ復帰式のシリンダーの力でレバーを介し、金型をクランプします。 アンクランプ UNCLAMP 一般油圧作動油(ISO VG32∼VG56) Recommended fluid LZ Type HI-CLAMP Clamps a die by the power of a single-action spring reset type cylinder via a claming lever. LZ2 LZ4 LZ6 LZ10 LZ16 LZ25 General hydraulic fluid (ISO VG32∼VG56) 質 量 Mass 注① NOTE① (kg) 3.0 4.8 9.4 15 使 用 頻 度 クランプ CLAMP LZ 仕 様 23 35 25回/日以下 Freqency limit 25Times/Day 耐 衝 撃 300m/s2 Shock limit 注① L=50時の質量を表示します。 NOTE① It denotes the mass when L=100. 型式表示方法 LZ TYPE DESIGNATION Tー 1 2 ー 3 ーA1 (クランプ能力19.6kN∼58.8kN) LZ Tー 1 2 ー 3 ーA2 (クランプ能力98.0kN∼245.0kN) 形状寸法 e b a :Clamping allowance b :Unclamping stroke H:Height of dies H1 D’ C’ B’ a :締め代 b :アンクランプ ストローク L1 L3 L2 T溝番号 T-slot number メーカーサイドで決定しますので、 T溝寸法をご指示ください。 To be determined by the manufacturer. specify dimensions of T-slots. a :Clamping allowance b :Unclamping stroke H:Height of dies A D C a :締め代 b :アンクランプ ストローク L1 左図H部をご確認下さい。 3 MAX. J 245.0kN Please confirm right picture H part. a b D’ C’ B’ L3 L2 M 19.6kN 39.2kN 58.8kN 98.0kN 157.0kN Height of dies:H(mm) 2 H N A’ Q P−Rc1/4 B 型式 項目 適用金型高さ H (MIN.∼MAX.) H1 a (at 24.5MPa) 金型高さ:H(mm) 2 H1 a 2 H P−Rc1/4 M MAX. J 2 4 6 10 16 25 F G e F G A’ Nominal clamping force LZ□T-A2(10ton∼25ton) LZ□T-A1(2ton∼6ton) N 呼称クランプ力 1 SHAPE AND DIMENSIONS D寸法の推奨公差±0.1mmです。 公差を±0.1mm単位でご指示下さい。 Recommended allowance ofsize D is ±0.1mm. Please direct the allowance in ±0.1mm. b e F G L1 L2 L3 M N P Q J LZ2 23∼60 61(23∼40) 71(41∼50) 81(51∼60) 2.5 3.5 8 66 30 LZ4 23∼70 78(23∼50) 88(51∼60) 98(61∼70) 2.5 4.5 9 78 LZ6 24∼80 95(24∼65) 105(66∼75) 115(76∼80) 2.5 4.5 7 98 LZ10 40∼80 H+65(40∼49) H+55(50∼59) H+45(60∼80) 3 LZ16 45∼80 LZ25 50∼80 80 18 14 13 ー 2 46 15 40 104 21 16 12 ー 2 61 20 50 128 25 18 12 25 3 80 19 5 11 104 55 158 28 20 28 28 3 ー 40 H+83(45∼54) H+73(55∼64) H+63(65∼80) 3 5 12 124 60 196 30 20 30 30 3 ー 50 H+102(60∼69) H+92(60∼69) H+82(70∼80) 3 5 12 145 72 238 38 25 38 30 3 ー 60 品質改良のため、予告なく仕様寸法の変更をすることがあります。 ご使用前にご確認ください。 Because of improvement of product quality, the dimensions in the specification are subject to change without notice. TRAIS 08100 LZ□F-A2 19.6kN∼ 157kN 構 造 共通仕様 CONSTRUCTION SPECIFICATIONS アンクランプ UNCLAMP 形 式 仕 様 クランプ CLAMP TYPE SPECIFICATION 耐 圧 Proof pressure 最高使用圧力 Maximum working pressure 最大クランプ力 MPa 36.8 MPa 24.5 kN 19.6 39.2 58.8 98.0 Maximum clamping force 単動バネ復帰式のシリンダーの力でレバ ーを介し、金型をクランプします。 スト ロ ー ク LZ Type HI-CLAMP Clamps a die by the power of a singleaction spring reset type cylinder via a claming lever. アンクランプストローク 6 7 7 8 8 (mm) 2.5 2.5 2.5 3 3 (mm) 3.5 4.5 4.5 5 5 Required volume of oil (m ) 6.0 13.8 19.9 39.6 85 Ambient temperatures range (℃) 締 Stroke め 代 Unclamp Stroke 所 要 油 量 使用温度範囲 使 用 油 General hydraulic fluid (ISO VG32∼VG56) 質 量 Mass 注① NOTE① ー5∼60 一般油圧作動油(ISO VG32∼VG56) Recommended fluid SHAPE AND DIMENSIONS (kg) 3.0 4.8 使 用 頻 度 9.4 14.6 26.2 25回/日以下 Freqency limit 25Times/Day 耐 衝 撃 300m/s2 Shock limit LZ□F-A2 157 (mm) Stroke 形状寸法 LZ2 LZ4 LZ6 LZ10 LZ16 注① L=50時の質量を表示します。 NOTE① It denotes the mass when L=100. 型式表示方法 e F G (クランプ能力19.6kN∼157.0kN) a b H H1 P−Rc1/4 n−dキリ M T MAX. J Nominal clamping force 2 4 6 10 16 S R X L3 L2 2 a :Clamping allowance b :Unclamping stroke h:Height of dies (at 24.5MPa) 19.6kN 39.2kN 58.8kN 98.0kN 157.0kN 金型高さ:H(mm) Height of dies:H(mm) H a :締め代 b :アンクランプ ストローク L1 呼称クランプ力 1 2 N U Y TYPE DESIGNATION 1 Fー 2 ーA2 固定式 LZ 項目 適用金型高さ H 型式 (MIN.∼MAX.) H1 a b e F G L1 L2 L3 M N P T X Y R S U n-d J LZ2 23∼60 61 (23∼40) 71 (41∼50) 81 (51∼60) 2.5 3.5 8 66 30 80 18 14 13 ー 2 H1-31 31 115 16 ー 90 2-16 15 LZ4 23∼70 78 (23∼50) 88 (51∼60) 98 (61∼70) 2.5 4.5 9 78 40 104 21 16 12 ー 2 H1-45 46 144 21 ー 110 2-22 20 LZ6 24∼80 95 (24∼65) 105 (66∼75) 115 (76∼80) 2.5 4.5 7 98 50 128 25 18 12 25 3 H1-55 60 180 30 ー 140 2-26 19 (34∼85) 130 (86∼95) 140 (96∼105) 3 LZ10 34∼105 120 5 9 108 55 155 28 20 14 30 3 H1-70 68 172 16 34 140 4-22 29 (36∼90) 145 (91∼100)155 (101∼110) 3 LZ16 36∼110 135 5 9 138 60 192 32 22 15 35 3 H1-73 82 220 20 42 180 4-29 33 エスアールエンジニアリング株式会社 S R ENGINEERING CO.,LTD. ●本社 HEAD OFFICE http://www.sr-engineering.co.jp e-mail [email protected] 〒651-2271 神戸市西区高塚台3丁目2番60 本社 (078)991-4400(代) Fax. (078)991-4406 e-mail [email protected] 開発部 (078)991-4407(代)Fax. (078)991-4443 e-mail [email protected] ●東京営業所 〒183-0005 東京都府中市若松町1丁目2-5 (042)369-6401(代) Fax. (042)369-6404 e-mail [email protected] ●中部営業所 〒471-0077 愛知県豊田市竹生町4丁目45番地 (0565)32-3081(代) Fax. (0565)32-3083 e-mail [email protected] http://www.sr-engineering.co.jp e-mail [email protected] 2-60, Takatsukadai 3-chome. Nishi-ku, Kobe, 651-2271 Japan SALES:Phone. (078)991-4400 Fax. (078)991-4406 e-mail [email protected] DEVELOP Phone (078)991-4407 Fax. (078)991-4443 e-mail [email protected] TOKYO BRANCH 2-5, Wakamatsu-cho 1-chome, Fuchu, Tokyo, 183-0005 Japan Phone. (042)369-6401 Fax. (042)369-6404 e-mail [email protected] CHUBU BRANCH 45, Takeo-cho 4-chome, Toyota, Aichi 471-0077 Japan Phone. (0565)32-3081 Fax.(0565)32-3083 e-mail [email protected] 品質改良のため、予告なく仕様寸法の変更をすることがあります。 ご使用前にご確認ください。 Because of improvement of product quality, the dimensions in the specification are subject to change without notice.
© Copyright 2024 ExpyDoc