抵抗溶接用 For resistance welding Air Cooling Resistance Welding Controller 水垢のつまりや、水の流し忘れ等 によるトラブルの心配不要。 Reduction of troubles Not using water for cooling, we do not have to worry the troubles due to the stock of scale in the tube, the failure of running water or etc. ロボット制御盤上 Property of Duty Effective use of space Able to set the welding controller on the robot controller 各種タイマーの定格電流比較表 Figure, showing the duty of each type of the timer controller 空冷 Air Cooling Inverter FAN × FAN ○ 200A 300A 10% 10% ① ② 機種 Type 使用率 Duty 安心設置 水冷 Water Cooling Inverter AC 400A 10% ③ AC FAN × 300A 10% ② 使用率と1次電流の特性 1次電流 Primary Current (A) Duty and Primary Current 500 ① ② ③ 400 300 200 盤内内部1個、外付最大2個取り付け可能 FAN1個につき、50A~100Aの使用率UP!! Cooling FAN 100 0 5 6 7 8 9 10 11 12 13 14 15 使用率 Duty (%) Able to install FAN for force cooling, at maximum one inside and two outside. Each FAN rises the usage rate about 50A ~ 100A. *タイマーの仕様により特性は異なります。周囲温度は45℃の場合となります。 手から手へ心から心へ伝える真の喜び 基本仕様 Specification 交流式抵抗制御装置 定格 定格電圧 Rating Rated Voltage 使用率 イ ン バータ式抵抗制御装置 AC Welding Controller Inverter Welding Controller 1Φ 380/400/415/440/460/480V±15%*1 3Φ380/400/415/440/460/480V±15%*1 300A 10%(ファ ン なし) Duty 溶接電源周波数 300A 10%(ファ ン なし) 300A 10%(without FAN) 300A 10%(without FAN) 50Hz/60Hz自動切り換え Automatic selection Rated Power Frequency 用周囲条件 Environment 温度及び湿度 Temperature and Humidity パワーユニット Power Unit 主回路制御素子 Main Circuit Element 冷却仕様 Cool Specifications 本体及びパワーユニット Enclosure and Power Unit イ ン ターフェ ース Interface I/O Input/Output 電流制御 制御方式 Current Control Control Method -5~+45℃ / 90%以下(但し結露しないこと) / Less than 90%(Without dewing) サイ リスタ(絶縁型) Isolatecd Thyristor IGBT(絶縁型) Isolated IGBT 自然空冷 (但しFAN付の場合強制空冷となる ) Natural air cooling (Forced air cooling with FAN) DeviceNet/CC-Link/ProfiBus/DIO*1 IGBTによ る ブ リッジ式PWMイ ン バータ制御 サイ リスタによ る 同期式位相制御 Bridge type PWM control by IGBT イ ン バータ周波数 700Hz~1,800Hz Synchoronous phase control using the thyristor 定電流制御 Constant Current Regulation 電圧補償制御 制御可能範囲 Control Range Voltage Compensation Control 二次電流制御範囲 ○ ○ ー 2.0~25.5kA Secondary Current 溶接トラ ン ス巻数比 4.0~200.0 Turn Ratio 機能 Function Inverter frequency 700Hz~1,800Hz ○ 溶接条件数 Weld Schedule 255 ステップ アップ 方式:選択(切、ステップ 、リニア) Stepper method (OFF, Step up, Linear up) ステッパー機能 Stepper Function ステップ 数:10ステップ (0~9 ステップ ) Number of step 10 steps(0~9 step) 電流低下検出レベル設定機能 Low Current Detection Level Setting Function 電流過大検出レベル設定機能 Over Current Detection Level Setting Function ○ ○ ○ ○ オプション対応機能 Optional Function 外形寸法 Outside Dimension *4 インバータタイプ Inverter type 正面 Front 交流タイプ AC type 600 正面 Front 400 510 210 加圧力コントロール機能*2 短絡検出機能*3 溶着(接触)検出機能*3 外傷検地機能 EtherNetによるデータ管理 インターフェーエスCC-Link インターフェーエスProfiBus Pressure Control Function Short Detect Function Deposition Function Primary Cable Detection Function Management Function by Ethernet Interface CC-Link Interface ProfiBus オプション品 Option 側面 Side 側面 Side 430 ◎ティーチングボックス ◎リセットボックス ◎リセットケーブル(1m~40m) *チップ間検出線 *WinTB2 Teaching Box Reset Box Reset Cable The Wiring for the Voltage Detection *ブレーカーなし Without Breaker 400 *1 いずれかを選択 *2 インターフェイスがDIOのときのみ選択可能 *3 どちらか一方を選択可能 *4 交流タイプはブレーカーなし、インバーター タイプはブレーカーありの外形寸法となります。 *ブレーカー内臓 With Breaker *1 Select either one *2 Select only with DIO *3 Select either one *4 Those show the outside dimensions - AC type without a breaker box and inverter type with a breaker box. 溶接に関する問い合わせ ナ・デックス技術センターにて本製品のデモンストレーションが行えます 溶接実験が行なえる環境がありますのでお気軽にお問い合わせ下さい。 お問い合わせは ! 安全に関する注意 正しく安全にお使いいただくためにご使用の 前には必ず「取扱説明書」をお読みください。 ご注意 ●当製品はキャッチオール規制の対象になります。輸出をするときは需要者・用途を確認後適切な手続きをおとりください。 ●仕様は改良のため予告なく変更する場合があります。 ●国内拠点 本社 〒460-8338 愛知県名古屋市中区古渡町9番27号 TEL:052-323-2215 FAX:052-322-3059 技術センター 〒481-0038 愛知県北名古屋市徳重御宮前1 TEL:0568-21-1428 FAX:0568-23-5540 東京支店 〒330-0802 埼玉県さいたま市大宮区宮町1-114-1(ORE大宮ビル8F) TEL:048-650-7181 FAX:048-650-7182 大阪支店 〒532-0011 大阪府淀川区西中島3-9-12(空研ビル) TEL:06-6305-0525 FAX:06-6305-5556 ●海外拠点 三河支店【三河安城】 北九州営業所【小倉】 【北米】ミシガン州・イリノイ州・カナダトロント 【中国】上海 【タイ】バンコク
© Copyright 2025 ExpyDoc