Waterbased EP Series Paint - Ennis

02
Performance Properties
EN 1436 Road performance results
Product Name WB1/WB2
Water Based Fast Dry
Certificate Numbers
RL/RW
Beta
Qd
SRT
Wet Thickness
1984/P-R-1
Class P7
Type 1
R4
B3
Q4
S2
428 Micron
1985/P-RW-II
Class P5
Type II
R3/RW3
B4
Q4
S1
428 Micron
1985/P-R-1
Class P5
Type 1
R3
B4
Q4
S1
428 Micron
1986/P-RW-II
Class P5
Type II
R2/RW1
B5
Q4
S1
475 Micron
Ennis-Flint is a worldwide leader in the traffic safety
and road marking industry providing quality and
performance-driven solutions designed to enhance
traffic safety for all users: drivers, pedestrians,
cyclists and pilots.
You can find Ennis-Flint products on roads and
highways, taxiways, runways, parking areas and in
commercial, contractor, governmental, industrial,
domestic, retail, airport and architectural settings.
With corporate headquarters in Thomasville, North
Carolina and manufacturing, distribution, and sales
locations occupying strategic points around the
globe, Ennis-Flint does not lose sight of the fact
our local relationships are what make and keep us strong.
Ennis-Flint EMEA (Europe, Middle East, Africa)
is equipped to serve and exceed our customers’
traffic safety and pavement marking requirements
with our full range of quality products, outstanding
geographic reach, and unmatched customer
support with areas of expertise including, but
not limited to:
—
—
—
—
—
—
—
—
—
—
—
Waterbased
EP Series Paint
Technical
Information
About Ennis-Flint
Paints
Aetec Certification Approval
An easy to apply, fast drying traffic paint formulated
specifically for airless equipment, conventional air atomised
equipment and also an ideal solution for roads, airports and
car parks.
Road Markings
Airfield Markings
Road Studs
High Friction Surfacing
Bridge Expansion Joints
Sealing and Crack Repair Systems
D
ecorative Crosswalks and Traffic
Calming Treatments
Surface Graphics Systems
Road Marking Performance Analysis
Traffic Products
Temporary Markings
This can be used in conjunction with glass beads for reflectivity.
It offers all of the benefits of a water based paint, and quickly dries to a no-track condition. This product
meets the requirements of TT-P-1952E Types I & II and TT-P-1952B. Available in White, Yellow, Black, Red,
Blue and Green – all colours are lead free. Available in 5 litre and 18.5 litre tins.
Contact Ennis-Flint
Product Services: +44 (0) 1257 225 100
Traffic Products: +44 (0) 1761 414 824
E-mail: [email protected]
Product Benefits
Drying Times
Non-flammable. Environmentally friendly and fast
drying. Equipment can be cleaned easily with water.
Demonstrates excellent bead retention. Keeps traffic
control to a minimum when striping. May be heated to
a maximum of 120F.
Dries to no pickup in less than 10 minutes @ 0.381mm
when ambient and surface temperature are 21oC/70F
or higher at 50% humidity. See conditions for
application overleaf for further information.
Recommended For
Lane lines, edge lines and centre lines on both asphalt
and concrete roadways, as well as symbols, legends,
car parks and airports.
Standards & Approved
Our waterbased EP Paint confirms to EN 1436 and
other international standards and has been approved
by SABS, BAST & Aetec.
Coverage
4.2m² per litre at 350 microns wet film thickness
Prismo Road Markings Limited (registered in England & Wales under registration number 05906228)
Registered Office: Drumhead Road, Chorley North Industrial Park, Chorley, PR6 7BX, UK.
www.ennisflint.com
www.ennisflint.com
Prismo
Paints
Typical Technical Data
Waterbased EP Paint
White
Lead Free Yellow
Colours
Percent Pigment by Weight
61
61
60
Percent Solids by Weight
(min.)
76
76
75
Percent Solids by Volume
(min.)
60
60
58
Viscosity (KU@ 77oF - 21.6oC)
80-85
80-85
80-85
Reflectance
85
50
Weight per Litres (min.)
51
59
56
Technical Information
Environmental
Conditions For Application
Dry to No Pickup
10 minutes @ 0.30mm
All products conform to the Federal Clean Air Act
Amendment of 1990. Volatile Organic Content is
below 100 grams per litre. All products are free
of lead, chrome and other heavy or toxic metals.
Consult MSDS for additional safety and regulatory
information.
All surfaces must be clean, dry and free from
oil, grease, antifreeze, loose sand, aggregate or
chipping or peeling paint. DO NOT apply when
temperatures are below 50°F or humidity is greater
than 85%. DO NOT apply when temperatures are
near or below the dew point or rain is forecast
within 2 hours. DO NOT apply if temperatures
expected to fall below freezing for 24 hours after
application. For complete drying and minimum dirt
retention, car parks should be closed to traffic for
two hours minimum after painting. New asphalt and
concrete should be allowed to cure for a minimum
of 30 days before the application of paint when
possible. Any curing compounds used on new
concrete must be mechanically abraded off prior to
striping. When striping on freshly sealed surfaces
use caution as some sealers can affect the curing
and adhesion of traffic paint.
Hiding Power
Complete @ 0.38mm
Flash Point
Non-Flammable – above 93oC (ASTM D-3278)
Reduction Solvent
Water
VOC Grams/Litre
<100 g/l
Clean-up Solvent
Water
Directions For Use
Mix thoroughly before using. Thinning is not
recommended and the product should be
considered ready for use. If thinning is necessary
for smaller equipment, add 0.5 litres of water
per 22 litres of paint. Product may be applied at
desired thickness up to 500 microns. Thicker films
will be slower drying and may exhibit cracking.
Recommended wet film application is 250 to 380
microns. Using a 315 – 317 or 415 - 417 airless tip
is a good starting point, with a pressure between
150 and 180 bar. Adjust application pressures and
tip sizes to get an even flat desired mil thickness
and line definition. If beaded application is required,
apply drop on beads at the rate of 0.4 kg to 0.6 kg
per litre of paint. DO NOT use organic solvents. All
equipment must be clean and flushed with water
before applying paints.
Equipment
All surfaces that come in contact with the paint
should be stainless steel, PVC plastic or a nonreactive material. Galvanized, brass, copper, mild
steel or aluminium will react with the product and
clog the equipment.
Clean-Up Of Equipment
Flush the equipment with water. For dried residue
a good household cleaner will aid in removal. A
mixture of 25% alcohol and 75% water can be
used to totally clean and flush the equipment, flush
equipment with water only before reloading paint.
<100 g/l
<100 g/l
Technical Data Sheet – Road Marking Products
Name
Fast Dry Waterbased Road Marking Paint
Codes
985201 White EP Series Enhanced
Caution
New asphalt surfaces should ideally be allowed to
age several months before lining. Latex paints will
not bleed on asphalt, but shrinkage of the paint
film during curing may cause new asphalt to lift or
crack. Exceeding the recommended film thickness
will increase the tendency to cause asphalt lifting.
If it is absolutely necessary to paint on new asphalt,
the paint must be diluted by means of adding 0.5
– 1litre of water per 5 litres of paint. The paint must
be sprayed with the lowest pressure possible to
produce a thin coat of no more than 180 microns of
wet film thickness. Check asphalt by applying a test
strip to aid in determining the readiness for painting.
If applying two coats or over-striping lines within
a fire lane, allow the first coat to dry fully before
applying the second coat. DO NOT apply when rain
is forecast. DO NOT apply when temperature and
humidity are near or below the dew point.
Disclaimer
The information given in these specifications and technical advice – whether verbal, or in writing or by way of trials is for guidance
only and is given in good faith, but without warranty. This also applies where proprietary rights or third parties are involved. Any
person using Ennis-Flint’s products without first making further enquiries as to the suitability of the products for the intended
purpose and testing the products to assess their fitness for the purpose does so at their own risk. The application, use and
processing of the products are beyond our control and are therefore your own responsibility, and we can accept no liability for the
performance of the products arising out of such use, beyond the value of the goods delivered by us. The information contained in
these data sheets is liable to modification from time to time in the light of experience and our policy of continuous development.
It is the user’s responsibility to ensure that this sheet is current prior to using the product.
Technical Data:Total solids wt%
Hiding Power @ 381 microns
> 76
Complete
Total solid volume %
> 60
Total Pigment wt%
60-62
NVV wt%
>41
Viscosity (KU@ 77oF . 21.6oC)
80-95
Density (kgs/litre
1.68
Flash Point ASTM D3278
Non-Flammable
pH
>10
VOC (g/L)
<100
Thinners
Water
Reducer
Water
Dry Time
12 Minutes
www.ennisflint.com

Download Report