CarPC JoyCon Exc User Guide

ChangJack.com
CarPC JoyCon Exc User Guide
NOV. 18th. 2014
CPJexc - CAN and IBUS Steering wheel controls USB interface
1. Feature of CarPC JoyCon Exc(CPJexc)
Hardware feature
- Converts CAN, IBUS, resistive and digital steering wheel controls into USB HID keyboard
and HID remote controller
- Resistance range adjustable
- Supported digital steering wheel controls :
BMW IBUS, AUDI ‘99-’04 (LIN), VW ‘99-’04 (LIN), Renault Clio, Hyundai(digital, Sonata2/3, Marcia,
Santamo), Renault SM (digital), Volvo XC70 ‘03
- Works same as standard USB HID keyboard and HID remote controller by hardware
- 24V tolerant 4 channel resistive(voltage) input
- Supports 28 physical buttons, 52 programmable logical buttons
- Long and Short button for one physical button, up to 5 simultaneous key strokes by one button.
- Supports Cyclic Button
- 6 programmable LED port
- Remote wake-up(resume PC from sleep with steering wheel controls)
- Channel Master/Slave selectable
- Supports J2P BUS peripherals(BSGc, BSGr, CPJ MIX)
- Phone/Mute signal output
- Supports BSGd(Button Signal Generator digital),
BSGd emulates BMW IBUS, AUDI ‘99-’04(LIN), VW ‘99-’04(LIN)
- Remote signal output for CPJ MIX
- SMPS power supplier circuit(Ultra low heat emission)
- Temperature range : -40 ~ +85°C
JoyCon Explorer feature(for Windows PC)
- Preset switching by buttons.
- Application Launcher(application launches and pops up with preset switching).
- Voice and OSD by button and preset switching.
- User definable button voice and OSD.
- Rearview by reversing light
- Online firmware update.
- No driver installation needs
- Powered by 12~14V DC(vehicle ACC)
- Available OS : Windows 8, Windows 7, Vista, XP, 2003
JoyCon Explorer supports Windows XP and the later version.
JoyCon Explorer does not support Linux, Mac. But CPJexc works on Linux and Mac after it is configured at Windows.
JoyCon Explorer does not support Android devices. But CPJexc works on Android devices (from Android version 3.1) after it is configured at Windows.
2. Contents
CAN cable x1
CarPC JoyCon Exc
1CH cable x1
7pin cable x1
3pin J2P cable x1
9pin cable x1
6pin LED cable x1
9pin connector x1, Heat Shrinkable Tube x2, User guide
*USB A-mini B 5P cable and JoyCon Explorer CD is optional. You can download JoyCon Explorer at
www.rcJoyCon.com
CarPC JoyCon Exc
ChangJack.Com
1
3. Board Layout
Brown
Yellow
Green
Blue
Gray
Black
Red
1. CH B : Input channel B for digital/resistive steering wheel controls
2.CH C : Input channel C for resistive steering wheel controls
3.CH D : Input channel D for resistive steering wheel controls
4.BSGD : The signal of digital BSG(button signal generator)
5.PHONE/MUTE : Phone/Mute signal. Active low.
6.Ground
7.12V IN(ACC). Audio noise can be heard without 12V supply.
Adjustment B
Tunes the resistance range
of input channel B
RESET
Short-circuit and power on(or
connect USB) for factory reset
Black
White
UPDATE
Short-circuit and power
on(or connect USB) to enter
firmware update mode
1.GND : Ground
2.CH A : Input channel A
for digital/resistive steering
wheel controls
Brown
Gray
Blue
Green
Yellow
Orange
Purple
Gray
Orange
Yellow
Green
1.CANH
2.CANL
Adjustment A
Tunes the resistance range
of input channel A
1.J2P DATA : J2P BUS data
2.HOST : J2P BUS host on/off state for BSGr
3.REM OUT(5V) : PC audio on/off state for
CPJ MIX
External LED port, 5V
1.LED1
2.LED2
3.LED3
4.LED4
5.LED5
6.LED6
USB
Onboard LED
Parallel Channel
Input port for Parallel output steering
wheel controls.
Peugeot 206,307,406,407, Renault Clio.
See Section 6.
(Car PC JoyCon Exd is sold with 9pin
connector not being soldered by default.)
DIP switch
Configures Channel A/B input signal
OFF ON
OFF
1
1 CH A
Resistive
2
3
2 CH A
Digital
3 CH B
Digital
CarPC JoyCon Exc
ChangJack.Com
ON
BMW IBUS
Resistive
Resistive
2
4. Operational test
Configure Channel A(or B) as resistive.(See Section 4. Installation of resistive steering wheel controller)
To check if CPJexc works properly, short-circuit the two wires of a input channel without connecting
steering wheel controls. If CPJexc works properly, the red indicator must goes to the left most side by
short-circuit, and returns to the right by open-circuit.
If the red indicator does not move, the CPJexc is broken.
Goes to the left most side.
9
8
7
6
5
4
3
2
1
Short Circuit
Returns to the right side.
9
8
7
6
5
4
3
2
1
Open Circuit
5. Installation of CAN steering wheel controls
Disconnect CAN wire from the car stereo and connect CPJexc’s CAN wire(CANH, CANL) instead of the car stereo.
Steering wheel
controls
CPJexc
CANL
Gray
CANH
Purple
6. Installation of BMW IBUS steering wheel controls
Connect IBUS wire to CH A.
If you want to use Tempomat controller, you can connect Tempomat Data wire to Channel B optionally.
CH A White
IBUS
Black
Brown
Tempomat Data CH B
CPJexc
Ground
BMW IBUS
steering wheel controls
12V
Radio Control(IBUS)
Tempomat
Ground
BMW E39
CarPC JoyCon Exc
BMW X5 E53, X3 E83
ChangJack.Com
Ground(Black)
Tempomat(Blue)
Radio Control(White)
12V(Gray)
3
Ground
Tempomat
Radio Control
12V
Turn on DIP switch 1 and turn off switch 2 for IBUS on Channel A.
Turn the Adjustment A dial to the end of counterclockwise.
Turn off DIP switch 3 for temponat signal on Channel B.
OFF ON
1
2
3
*12V power(ACC) must be supplied to CPJexc for BMW IBUS.
7. Installation of resistive steering wheel controller
Connect CPJexc’s input channel(CH A, CH B, CH C, CH D)wire to the steering wheel control’s resistive
White
signal wire.
Black
CH A
Ground
CH B
Brown
CPJexc
Warning!! Do not connect signal and Ground wire reversely.
OFF ON
1
2
3
Turn off DIP switch 1, turn on DIP switch 2
to use Channel A as resistive.
OFF ON
1
2
3
Turn DIP switch 4 on
to use Channel B as resistive.
If the buttons in JoyCon Explorer are too close each other, tune the Adjustment A/B on the Board.
Adjustment A
Adjustment B
Default position of Adjustment
A/B is center.
CarPC JoyCon Exc
ChangJack.Com
4
8. Installation of digital steering wheel controller
8-1. AUDI ‘99-’04
Connect Radio control Data to CH A. Turn off DIP switch 2 and 3.
Data
Ground
White
CH A
CPJexc
Black
OFF ON
1
2
3
8-2. VW(Volkswagen) ‘99-’04
Connect Radio control Data to CH A. Turn off DIP switch 2 and 3.
Data
Ground
White
CH A
CPJexc
Black
OFF ON
1
2
3
8-3. Volvo XC70 ‘03
Connect Radio data signal to Channel A. Turn off DIP switch 2 and 3.
Data White CH A
Ground Black
CarPC JoyCon Exc
CPJexc
OFF ON
1
2
3
ChangJack.Com
5
8-4. Hyundai Marcia Sonata2/3
Connect Radio control data to Channel A. Turn off DIP switch 2 and 3.
Data
Ground
Data
12V
Ground
White
Black
CH A
CPJexc
OFF ON
1
2
3
8-5. Renault SM
Connect Radio control signal to Channel A. Turn off DIP switch 2 and 3.
Ground
Data
12V
Radio Control
Signal(Resistive)
Data
Ground
12V
Data
Ground
White
Black
CH A
CPJexc
Data White CH A
Ground Black
Signal
Brown
CH B
CPJexc
OFF ON
1
2
3
CarPC JoyCon Exc
ChangJack.Com
6
9. Installation of parallel channel
9-1. Renault Clio
Connect Radio control signal to Parallel Channel, which is recognized as CH A in JoyCon Explorer.
BLUE
BROWN
YELLOW
BLACK
GREEN
RED
Brown
Gray
White
Blue
Green
Yellow
Brown
Gray
White
Blue
Green
Yellow
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
9-2. Peugeot 206 307 406
Connect Radio control signal to Parallel Channel.
Black
Brown
Gray
White
Blue
Green
Yellow
Orange
CarPC JoyCon Exc
ChangJack.Com
9
8
7
6
5
4
3
2
1
7
9-3. Peugeot 306
Connect Radio control signal to Parallel Channel.
Black
Blue
Green
Yellow
Orange
9
8
7
6
5
4
3
2
1
9-4. Ford Mondeo MK2 ‘96-’00
Connect Radio control signal to Parallel Channel.
Black
White
Blue
Green
Yellow
Orange
9
8
7
6
5
4
3
2
1
10. POWER and LED
External Power is required for CPJexc to work when the PC power is off.
Connect ACC(12V) to 7 pin, connect chassis ground to 6 pin.
For external LED, a current limit resistor(usually 330ohm) must be connected in series. Without the
current limit resistor, LED burns out. Black wire is Ground. LED output is 5V.
12V(ACC)
Ground Black
Ground
LED1 Brown
Gray
9
8
7
6
5
4
3
2
1
LED2
11. Factory Reset
1. Remove the external power. 12V(ACC)
2. Short-circuit two reset points.
3. Connect USB.
1
UPDATE
RESET
2
9
8
7
6
5
4
3
2
1
3
CarPC JoyCon Exc
ChangJack.Com
8
CarPC JoyCon Exc User Guide - Software Setup
CPJexc - CAN and IBUS Steering wheel controls USB interface
1. Setup of CAN steering wheel control buttons
Check Setting and click CAN Scan, then CPJexc CAN Scanner pops up.
Click Start Scan and press the steering wheel buttons, CAN messages are listed at left listbox.
Drag and drop the CAN messages to the right listbox or copy the CAN message to the left listbox
with the “>” button. The CAN message in the right listbox can be used as a Button.
Drag-Drop
You can save the CAN messages as a file(.can) with Save button or load CAN messages from a file(.
can) with Load button.
“Dur:” is duration of the CAN message. If the CAN message is repeated periodically while the button
is being pressed, set the duration above 0. The unit of “Dur” is 10ms.
CarPC JoyCon Exc
ChangJack.Com
9
To assign the CAN button message as a button, select a button in the drop down list. CAN button
can be assigned to all channel buttons.
Up Button appears as a gray bar, Down Button appears as a green bar.
A2 Up Button
A2 Down Button
Button bar turns to green when the steering
wheel button is pressed.
Click Apply to download the CAN button setting.
You can save the CAN button setting as a file(.cbn) with Export button or import CAN button setting
from a file(.cbn) with Import button.
You can see only the message with the ID you want by checking Enable
CAN ID Filter at ID filter Dialog.
You can send the CAN message with Send command or by doubleclicking the CAN message in the listbox. If the Show sent CAN message
is checked, the CAN message sent on the CAN bus is listed in the left
listbox.
CAN baudrate can be configured at CAN Config dialog.
Periodic message is sent on CAN bus periodically by the period. Periodic message is requied to receive data from some device(eg. I-Drive Controller).
CarPC JoyCon Exc
ChangJack.Com
10
The data of CAN message can be masked at CAN Button Property dialog box. Unexpected data bit
can be ignored by setting the mask bit as 0.
2. Setup of IBUS steering wheel control buttons
Choose BMW Audio Control(I-BUS) in MISC Tab.
In the Button Tab, check Setting and click IBUS Scan, then
CPJexc IBUS Scanner pops up.
CarPC JoyCon Exc
ChangJack.Com
11
Click Start Scan and press the steering wheel buttons, IBUS messages are listed at left listbox.
Drag and drop the IBUS messages to the right listbox or copy the IBUS message to the right listbox
with the “>” button. The IBUS message in the right listbox can be used as a Button.
Drag-Drop
You can save the IBUS messages as a file(.ibs) with Save button or load IBUS messages from a
file(.ibs) with Load button. “Dur:” is duration of the IBUS message. If the IBUS message is repeated periodically while the button is being pressed, set the duration above 0. The unit of “Dur” is
10ms. For example, put “Dur:12” in IBUS button message of the BMW volume+/-.
To assign the IBUS button message as a button, select a button in the drop down list. IBUS button
can be assigned to all channel buttons.
Up Button appears as a gray bar, Down Button appears as a green bar.
A2 Up Button
A2 Down Button
Button bar turns to green when the steering
wheel button is pressed.
Click Apply to download the IBUS button setting.
You can save the IBUS button setting as a file(.ibn) with Export button or import IBUS button setting from a file(.ibn) with Import button.
CarPC JoyCon Exc
ChangJack.Com
12
You can see only the message with the ID you want by checking Enable
IBUS ID Filter at ID filter Dialog.
You can send the IBUS message with Send command or by doubleclicking the IBUS message in the listbox.
If the Show sent IBUS message is checked, the IBUS message sent on
the IBUS bus is listed in the left listbox.
Periodic message is sent on IBUS bus periodically by the period.
The data of IBUS message can be masked at IBUS Button Property dialog box. Unexpected data bit
can be ignored by setting the mask bit as 0.
CarPC JoyCon Exc
ChangJack.Com
13
3. Setup of resistive steering wheel control buttons
Check Setting and click Auto Detect. After auto-detection starts, press steering wheel control buttons one by one. After all the buttons are detected, click Auto Detect again to finish auto-detection.
Clear button clears all the buttons detected. You can also tune the Resistor Range and Position
manually by putting the values in the edit boxes. Click Save/Apply after you change the values.
If the button bars are too close each other, tune the Adjustment A/B on the Board.
(Resistor range and position of the buttons are stored in the onboard memory of CPJexc.)
Button bar turns to green when the steering wheel button is pressed.
CarPC JoyCon Exc
ChangJack.Com
14
4. Setup of digital steering wheel control buttons
Check Setting and click Auto Detect. After auto-detection started, press steering wheel control buttons one by one. After all the buttons are detected, click “Auto Detect” again to finish auto-detection
and click “Save/Apply” to download the steeing to CPJexc. “Clear” button clears all the buttons detected. (Detected buttons are stored in the onboard memory of CPJexc.)
5. Connecting a button to the hotkey
Drag-drop Button Bar to the keyboard keys(or HID remote controller buttons). Up to 5 can be connected to one button.
Drag-drop sequence is same with the keyboard key stroke sequence.
For example, if you want a button to generate hotkey CTRL+ALT+DEL, drag-drop the Button Bar on
the CTRL first, ALT next and DEL last.
Drag-Drop
CarPC JoyCon Exc
ChangJack.Com
15
6. Disconnecting a buttons from the function
Right-click the Button Bar or keyboard key(or HID remote controller button) and click an item in the
drop down menu. Or drag-drop the Button Bar to the connected keyboard key(or HID remote controller button) again.
7. Save / Restore Preset
Save the hotkeys and configuration as a preset file(.prs) by Save(Save As) button.
Restore the hotkeys and configuration by Open Preset button or by double-clicking a preset file(.prs)
or by drag-drop of a preset file(.prs) to the preset edit view.
(Resistor range and position of the buttons are stored in the onboard memory of CPJexc.)
Save As
Save
Open Preset
New Preset
Clear
Drag-Drop
CarPC JoyCon Exc
ChangJack.Com
16
Extended Button Setting
1. Short Button and Long Button
CPJexc supports two separated functions for one steering wheel remote control button.
The two functions are Short Button and Long Button.
Short Button is generated when the remote control button is pressed or released before Critical
Time. Long Button is generated when the remote control button is released after Critical Time.
To use Long Button, set the Critical Time over than 0, then Long Button Bar will appear above the
Short Button bar.
Long Button
Short Button
2. Separate Short and Long button
When you want to generate only the long button, the short button is required not to be generated
immediately by pressing the remote control button.
Put 1~254 in S-Hold Time.
The short button is generated when the button is released before Critical Time while S-Hold Time.
The long button is generated when the button is released after Critical Time while L-Hold Time.
Hold Time value 1 is about 10ms, so Hold Time value 254 is about 2540ms(2.54s).
Hold Time 0 means that the button keeps being pressed while you keep pressing the remote control
button. This is useful when you need to keep a key pressed in volume control.
(C, D channel support only Short Button and S-Hold Time.)
3. Toggle Button
If the Hold Time of a button is 255, the button is toggled.
This is useful when a keyboard key need to be stroked while SHIFT, CTRL, or ALT keys are kept
pressed. (For example, ALT+TAB or Window+TAB)
CarPC JoyCon Exc
ChangJack.Com
17
4. Cyclic Button
You can rotate buttons by checking Cyclic Button. The cyclic buttons rotate by pressing any checked
button.
For example in the next picture, when you press A1(or A2 or A3 or A4),
button works A1->A2->A3->A4->A1->A2....
5. Programmable LED control
CPJexc can control one onboard LED and two external LEDs.
If you want to control LED with the current preset, check Control in the LED tab. If Control is not
checked, this preset doesn’t control LED and LED keeps previous configuration.
If Reverse is checked, On Off is reversed.
If Turn Off on Sleep is checked, LED is turned off when the PC goes into sleep mode.
LED control has 8 modes.
0. Always On : LED is turned on always
1. Always Off : LED is turned off always
2. On by a button : LED is turned on while a button is pressed.
3. Blink by a button : LED blinks periodically while a button is
pressed.
4. Toggle by a button : LED is turned on by pressing a button,
and is turned off by another pressing the button.
5. Toggle blink by a button : LED blinks periodically by pressing
a button, and is turned off by another pressing a button.
6. On by a button, off after a period : LED is turned on by
pressing a button, and is turned off after a period automatically.
7. On by any button, off after a period : LED is turned on by pressing any button, and is turned off
after a period automatically.
Unit of Period is millisecond. In the blink mode(3, 5), turning on is one period and turning off is another period. For example, if the Period is 500(ms), LED is turned on every 1 second(1000ms).
To assign a button to LED, drag-drop a button to a LED.
CarPC JoyCon Exc
ChangJack.Com
18
Preset Switching
A preset can be downloaded to CPJexc by Preset Button automatically, it is useful when you need to
change steering wheel remote control’s configuration while driving.
1. Preset List
Drag Drop preset files on the list of Preset tab. Preset is switched with the sequence of this list.
Drag-Drop
2. Preset Button
The presets are switched in sequence by Preset Up/Down Button. An application which is associated with the current preset in Application Launcher is closed by Close Button, Launched by Launch
Button. Configure the Preset Button of every preset file in the preset list in the same way(S-Hold Time,
L-Hold Time and Critical Time).
CarPC JoyCon Exc
ChangJack.Com
19
There is another way to switch the presets. You can download a preset and launch an application
directly not in sequence with Preset Button in the preset list. The application which is associated with
the preset is closed by Close Button in the Preset List. Configure the Preset Button of every preset
file in the preset list in the same way(S-Hold Time, L-Hold Time and Critical Time).
3. Application Launcher
An application can be launched and popped up when Preset is switched. Drag-drop (.exe) file(or
shortcut file) or double-click current running application in the list box. Name is spoken when the application is launching. If the application is not running, the application is launched. If the application is
already running, the application pops up. If the Track top window is checked, Preset is automatically
switched by the top window.
4. Start option
Check Start with Windows to run JoyCon Explorer when Windows starts.
Check 1st Preset when Starting to run the first preset in the preset list when the JoyCon Explorer
starts. “Run Preset” means to launch or pop up an application with opening an preset).
Check Open this Preset when Starting and drag-drop a preset on the edit box, to open the preset
when JoyCon Explorer starts.
CarPC JoyCon Exc
ChangJack.Com
20
CarPC JoyCon Exc User Guide -BSG (Button Signal Generator)
CPJexc - CAN and IBUS Steering wheel controls USB interface
BSG(Button Signal Generator) emulates the button signal that controls the car stereo. CarPC JoyCon
Exc(CPJexc) itself supports BMW IBUS, AUDI ‘99-’04(LIN) and VW(Volkswagen) ‘99-’04(LIN) by BSGd
pin. BSGc(Button Signal Generator CAN) and BSGr(Button Signal Generetor Resistive) are an external devices connected through J2P BUS. BSGc(Button Signal Generator CAN) generates CAN signal.
BSGr generates resistive button signal. (J2P BUS is a signal wire that connects CPJexc and its peripherals.)
1. BMW IBUS
1-1. Installation of BSGd for BMW IBUS
You can control both car PC and BMW stereo with steering wheel controls using BSGd.
Connect the steering wheel controller’s IBUS wire to Channel A. Connect BSGd wire to the car stereo
instead of steering wheel controller’s IBUS wire.
White
IBUS CH A
BSGd
IBUS
Blue
9
8
7
6
5
4
3
2
1
CPJexc
IBUS
Modified connection
Original connection
1-2. JoyCon Explorer Setting
Choose the number of BSG device in Num. of BSG.
Choose the BSG index.
Choose the Type of BSG as BMW I-BUS.
BSG Index
Check “Bypass Steering Wheel Controls to Head
Unit”, if you want to bypass all the messages which
are originated from the steering wheel controls and
which are not used as a button.
Check “Bypass Head Unit to Steering Wheel Controls”, if you want to bypass all the messages which
are originated from the head unit and which are not
used as a button.
CarPC JoyCon Exc
ChangJack.Com
21
Drag and Drop IBUS message from the CPJexc IBUS Scanner to BSG Button.
IBUS message of Up Button is generated when the steering wheel button is pressed.
IBUS message of Down Button is generated when the steering wheel button is released.
Name of BSG button is spoken when the Button is pressed.
Drag-Drop
The IBUS Message dialog box appears by clicking the BSG button. You can type IBUS message in the
edit box. “Dur:” is duration of the IBUS message that is repeated while the button is being pressed.
(For example, BMW stereo Volume+/- button requires Dur:10.)
You can test the BSG button by clicking the
number. And you can also test the Down
or Up message by Send command in the
context menu that appears by right clicking
of the button message.
Drag-drop buttons to the BSG buttons to connect a
steering wheel button to a BSG button.
Click to Test
Drag-Drop
BSG settings can be saved as or restored from
a file(.bsg) with Import and Export button.
CarPC JoyCon Exc
ChangJack.Com
22
2. CAN
2-1. Installation of BSGc(Button Signal Generator CAN)
You can control both car PC and car stereo with steering wheel controls using BSGc.
BSGc(Button Signal Generator CAN) is an external device connected through J2P BUS.
Connect CPJexc’s HOST and J2P to BSGr’s HOST and J2P respectively.
Connect BSGc’s CAN (CANH, CANL)wire to the car stereo’s CAN wire.
Steering wheel
controls
Purple
CANH
Gray
CANL
HOST
J2P
Yellow
Oragne
BSGc
CANL
Gray
CANH
Purple
CPJexc
Car Stereo
2-2. JoyCon Explorer Setting
1. Choose the number of BSG device in Num. of BSG.
2. Choose the BSG index.
3. Choose the Type of BSG as BSG-C.
BSG Index
Check “Bypass Steering Wheel Controls to Head
Unit”, if you want to bypass all the messages which
are originated from the steering wheel controls and
which are not used as a button.
Check “Bypass Head Unit to Steering Wheel Controls”, if you want to bypass all the messages which
are originated from the head unit and which are not
used as a button.
CarPC JoyCon Exc
ChangJack.Com
23
Drag and Drop CAN message from the CPJexc CAN Scanner to BSG Button.
CAN message of Up Button is generated when the steering wheel button is pressed.
CAN message of Down Button is generated when the steering wheel button is released.
Name of BSG button is spoken when the Button is pressed.
Drag-Drop
The CAN Message dialog box appears by clicking the BSG button. You can type CAN message in the
edit box. “Dur:” is duration of the IBUS message that is repeated while the button is being pressed.
You can test the BSG button by clicking the
number. And you can also test the Down
or Up message by Send command in the
context menu that appears by right clicking
of the button message.
Drag-drop buttons to the BSG buttons to connect a
steering wheel button to a BSG button.
Click to Test
Drag-Drop
BSG settings can be saved as or restored from
a file(.bsg) with Import and Export button.
CarPC JoyCon Exc
ChangJack.Com
24
2. AUDI ‘99-’04(LIN) and VW(Volkswagen) ‘99-’04(LIN)
Connect the steering wheel controller ‘s LIN wire to Channel A. Connect BSGd wire to the Radio inWhite LIN CH A
stead of steering wheel controller ‘s LIN wire.
BSGd
LIN Control
Module
9
8
7
6
5
4
3
2
1
Blue
CPJexc
LIN Control
Module
Modified connection
Original connection
1. Choose the number of BSG device in Num. of BSG.
2. Choose the BSG index.
3. Choose the Type of BSG.
4. Put the Name of BSG button that is spoken when the Button is pressed.
5. Drag-drop buttons to the BSG buttons.
BSGr needs resistance values for each BSG button. The resistance unit is ohm(Ω).
Sony radio needs shift signal for Next/Previous button, check the checkbox for Next/Previous Album
button.
BSG settings can be saved as or restored from a file(.bsg).
BSG Index
Drag-Drop
Download the latest user guide at this URL.
http://www.changjack.com/user_guide/cpjexc/CPJexc_UserGuide_eng.pdf
CarPC JoyCon Exc
ChangJack.Com
25

Download Report