FVCCH-75X - CRUX Interfacing Solutions

INTERFACING SOLUTIONS
FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
DODGE
2014 - 2015 Durango
2014 - 2015 Ram
FVCCH-75X
WORKS WITH:
VEHICLES WITH FACTORY
REAR-VIEW CAMERA
JEEP
2014 - 2015 Grand Cherokee
APPLICATION NOTES:
FOR UCONNECT 5” AND 8.4”
DISPLAYS
This interface does not offer the
Force RVC feature.
Contact Tech Support for more
information.
PARTS INCLUDED
(1) CH-75X CAN Module
(1) CH-75X FVC Module
(1) CH-75X 52-Pin T-Harness
(1) Instruction Sheet
SAFETY PRECAUTIONS
1. Please read through the entire instruction manual before starting any of the installation procedures.
2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.
3. Do not install any of the main modules near any major components or near the HVAC system,
as placing items near the HVAC may cause damage or overheating to the vehicle or interface.
4. We recommend not disconnecting any of the air bag connections behind the dash panels.
5. This product is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where
the device shows proof of being opened or improper extreme force.
TECH SERVICES
All our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems or if
you have technical questions, contact us directly:
Crux Interfacing Solutions Tech Support
1 (855) 822-1348 (Mon - Fri - 9:00 AM - 5:00 PM) Pacific Time
Rev. 101614
1
www.cruxinterfacing.com
FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
INTERFACING SOLUTIONS
FVCCH-75X
INSTALLATION OVERVIEW
52-PIN
TO FACTORY
RADIO
52-PIN
(male plug)
(female plug)
8-PIN
(male plug)
VIDEO
(male plug)
FRONT CAM INPUT
(female plug)
ON
1
2
3
4
5
6
STATUS LED’S
FRONT ACTIVE/12V/GRAY
RED/
POWER
12V
8-PIN
(male plug)
ON
1
2
3
4
5
BLACK/
GROUND
6
DIP SWITCHES OVERVIEW
FRONT CAMERA
(not included)
STATUS LED’S
Make sure to set dip switch number 2
on both modules to ON.
REAR-VIEW
INTERFACE
Dip 2 = RVC Enable
ON
ON
1
ACTIVATE
REAR-VIEW
Rev. 101614
FRONT-VIEW
INTERFACE
2
3
4
5
DIP 1 = OFF
2 = ON
3
4
OFF
5
DIP 6
6
1
ACTIVATE
FRONT-VIEW
2
2
3
4
5
Dip 2 = FVC Enable
6
DIP 1 = OFF
2 = ON
3
4
OFF
5
DIP 6
www.cruxinterfacing.com
INTERFACING SOLUTIONS
FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
FVCCH-75X
CONNECTING THE INTERFACE
Follow these steps to properly install the CAN module
Step 1 - Remove the factory display to gain access to the factory 52-Pin (RED) connector.
Located behind the display, not the radio. Remove the factory 52-Pin connector.
Step 2 - Using the provided 52-Pin T-Harness, mate both sides of the harness, to the factory harness and the factory display.
Rev. 101614
3
www.cruxinterfacing.com
INTERFACING SOLUTIONS
FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
FVCCH-75X
CONNECTING THE INTERFACE
Follow these steps to properly install the CAN module
Step 3 - Connect EACH module to its 8-Pin connector on the provided T-Harness. (See labels on T-Harness)
Make sure all your connections are firmly inserted.
Step 4 - After connecting the module, set dip switch number “2” to the “ON” position.
Make sure to activate the FVC, otherwise no signal is received and you will only see a black screen.
FVC Module DIP 2: Front-View Camera Enable
All other dip switches are not to be used.
LED STATUS AND DESCRIPTION (Visible next tot the Dip Switches)
BLUE LED:
Blinking = No BUS Detected. Solid = BUS Recognized. Rev. 101614
RED LED:
ON = Power On
OFF = Power OFF
4
www.cruxinterfacing.com
FVCCH-75X
FRONT-VIEW CAMERA
52-PIN
(female plug)
INTEGRATION INTERFACE
FOR
DODGE & JEEP VEHICLES 2014-UP
INTERFACING SOLUTIONS
CONNECTING THE FRONT-VIEW CAMERA
In order to activate the Front-View Camera feature, make sure Dip switch number 2 is set to “ON”.
Step 5 - Connect the RED power 12V cable from the camera to the GREEN Reverse (12V) trigger on the T-Harness.
Tap the BLACK wire on the T-Harness 8-Pin connector for the GROUND to the camera.
VIDEO
(male plug)
FRONT CAM INPUT
(female plug)
D’S
FRONT ACTIVE/12V/GRAY
RED/
POWER
12V
8-PIN
(male plug)
ON
1
2
3
4
5
BLACK/
GROUND
6
FRONT CAMERA
(not included)
STATUS LED’S
Be sure to test the camera by pressing the BACK button on the radio side and confirming the camera display.
SWITCHING TO THE FRONT-VIEW CAMERA
FRONT-VIEW
To switch to the new FVC, simply
press the
INTERFACE
“BACK” once. To Exit the FVC press
BACK once.
ON
(Front Camera is on a permanent 12 second timer)
Or is the camera on a switch mode.
1
ACTIVATE
FRONT-VIEW
Rev. 101614
2
3
4
5
DIP 1 = OFF
2 = ON
3
4
OFF
5
6
5
www.cruxinterfacing.com
INTERFACING SOLUTIONS
FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
FVCCH-75X
COMPATIBLE RADIOS - ALL RADIO MUST BE 1-PIECE RADIOS (NO SEPARATE CD SLOT)
8.4” UConnect
5” UConnect
Rev. 101614
6
www.cruxinterfacing.com

Download Report