Electronic Thermostats RTE RTE 102/104 Setting of temperature on the RTE 102/104 is done on the circuit board under the housing to prevent unauthorised persons from changing the selected temperature. Thermostats are designed to control heat directly or to be used as sensors in larger centrally controlled facilities. Type RTE 102 RTE 104 Connection voltage V 230 400 Max. current breakpoint Contact function Setting range Regulator precision Setting Height x Width x Depth Weight Protection class Code A 15 breaking 7 - +35 ± 0.3 internal 71x71x28 90 IP 30 RTE102 8 breaking 7 - +35 ± 0.3 internal 71x71x28 90 IP 30 RTE104 °C °C mm g RTEV 102/104/102V RTEV 102/104 is equipped with a dial for setting the temperature. The setting range can be limited on the back of the dial and the thermostat can be calibrated there as well, if necessary. RTEV 102V is also equipped with an alternating relay and can therefore be used for the regulation of heating or cooling. External sensors mounted in ventilation ducts or the floor can also be connected. Type Connection voltage Max. current breakpoint Contact function Setting range Regulator precision Setting Height x Width x Depth Weight Protection class Code V A °C °C mm g RTEV 102 RTEV 104 RTEV 102V 230 15 breaking 7 - +35 ± 0.3 external 71x71x28 90 IP 30 RTEV102 400 8 breaking 7 - +35 ± 0.3 external 71x71x28 90 IP 30 RTEV104 230 15 alternating 7 - +35 ± 0.3 external 71x71x28 90 IP 30 RTEV102V RTEV 202/204 RTEV 202/204 has a function switch for on/off connection as well as the optional connection of external sensors. A fixed temperature reduction of 4ºC can be activated by an externally connected contact, such as a weekly timer. The setting range can be limited and calibrated on the setting dial. RTEV 302 RTEV 302 also has a built-in clock function in addition to the dial and the option of connecting external duct or floor sensors. The period for temperature reduction by 4ºC is 5, 7, 12, or 16 hours. The preferred period is set on the circuit board upon in-stallation. The reduction period is activated by pushing the start button at the desired time of day. The clock is then set and the reduction period starts at that time every day automatically. An ongoing temperature reduction period can be interrupted with a push of the start button. The following day, the reduction period once again begins at the usual set time. Type Connection voltage Max. current breakpoint Contact function Setting range Regulator precision Setting Height x Width x Depth Weight Protection class Code V A °C °C mm g RTEV 202 RTEV 204 RTEV 302 230 15 breaking 7 - +35 ± 0.3 external 400 8 breaking 7 - +35 ± 0.3 external 230 15 breaking 7 - +35 ± 0.3 external 71x71x28 90 IP 30 RTEV202 71x71x28 90 IP 30 RTEV204 71x71x28 90 IP 30 RTEV302 The thermostats are approved by SEMKO and meet the standards of the EMC Directive. Accessories Code External floor/ duct sensor RTS 01 More Information More information is found in our Heating and Energy Handbook and on the Internet at www.frico.se. 991118/IT All thermostats have a fixture hole that fits the unit housing and an indicator that shows when the thermostat is on. The thermostats can be complemented with covering frames available on the market. Frico AB, Box 102, SE-433 22 Partille, Sweden Tel: +46 31 336 86 00 Fax: +46 31 26 28 60 [email protected] www.frico.se Design and specifications are subject to change without notice.
© Copyright 2025 ExpyDoc
