Kendo Closet Rod - Installation Instructions Models KCR- Please read all instructions prior to installation and keep for future reference! 1. Product to be installed by a qualified electrician. 2. Must be installed per NFPA 70, article 410.16. 3. Prior to installation ensure power is off at fuse box to prevent electrical shock. 4. Dry locations only. Pour emplacements secs seulement. 5. Use only with Class 2 power unit. Utiliser seulement avec la classe 2 unite d’alimentation electrique. 6. Suitable for installation within the closet storage space. Convenable pour installation dans l’espace de stockage de placard. 7. Max 25 pounds per 6 inch with mounting supports. Max 25 livres par 6 pouces avec monter des soutiens. 1 4002302 - Conforms to ANSI/UL STD 2108 - Certified to CAN/CSA STD C22.2 No. 250.0-08 Page 1 of 2 mounting end cap every 20" 1.1 6264 Oakton St Morton Grove IL 60053 T 224.333.6033 F 224.757.7557 [email protected] www.luminii.com 1.3 extrusion extrusion 1.1 Slide the support bracket (MC-R3) into the Kendo Closet Rod extrusion. One support bracket must be installed every 20" for proper weight support distribution. extrusion support bracket 1.2 Carefully remove the protective film from the diffuser. 1.1 diffuser 1.2 1.3 Push the mounting end cap (MC-R2) onto each Kendo Closet Rod extrusion end. film 2 2.1 2.1 Push LED lead wires (or DC quick connect cable) through opening in mounting surface for running wires to remote power supply. 2.2 lead wires LED support bracket screw 2.2 Mounting surfaces for Kendo Closet Rod to be flat and structurally sound. All supports to be secured to mounting surfaces with screws attached to structurally sound framing and/or blocking. Mount intermediate support with two screws penetrating into framing and/or blocking every 20” of Kendo Closet Rod extrusion. Locate diffuser lens in the down position. screw 2.3 mounting end cap mounting end cap drywall wood block 2.3 Mounting brackets installed on each of the ends of the Kendo Closet Rod extrusion orientate two of the three mounting holes in the up position and install. 3a Lead wire power feed Class II power supply power to 24 VDC Kendo Closet Rod light fixture 3a Ensure power is off to power supply! Then proceed to connect Kendo Closet Rod LED lead wires to power supply. For wiring instructions please refer to power supply wiring instructions. See page 2 - step 4 - for quick connect power feeding. 3a See page 2 - step 3b - for quick connect power feeding 120 VAC 24 VDC *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV1.0 Kendo Closet Rod - Installation Instructions Models KCR- Please read all instructions prior to installation and keep for future reference! 1. Product to be installed by a qualified electrician. 2. Must be installed per NFPA 70, article 410.16. 3. Prior to installation ensure power is off at fuse box to prevent electrical shock. 4. Dry locations only. Pour emplacements secs seulement. 5. Use only with Class 2 power unit. Utiliser seulement avec la classe 2 unite d’alimentation electrique. 6. Suitable for installation within the closet storage space. Convenable pour installation dans l’espace de stockage de placard. 7. Max 25 pounds per 6 inch with mounting supports. Max 25 livres par 6 pouces avec monter des soutiens. 4002302 - Conforms to ANSI/UL STD 2108 - Certified to CAN/CSA STD C22.2 No. 250.0-08 Page 2 of 2 6264 Oakton St Morton Grove IL 60053 T 224.333.6033 F 224.757.7557 [email protected] www.luminii.com 3b Quick connect power feed cable Class II power supply 3b Ensure power is off to power supply! Then proceed to connect Kendo Closet Rod LED male quick connector to female connector of power supply. For wiring instructions please refer to power supply 3b + 120 VAC TO KENDO CLOSET ROD 24 VDC - 4 4.1 To connect two sections of the Kendo closet rod simply use the male and female quick connectors. If compatibility is an issue, the female/male adapter can be used as needed. Also, if the two sections of Kendo closet rod are located at a distance from each other, extension cables can be ordered up to 10’ long (view specsheet for available lengths). 4.1 TO POWER SUPPLY FEMALE QUICK CONNECT TO POWER SUPPLY FEMALE QUICK CONNECT MALE QUICK CONNECT MALE QUICK CONNECT FEMALE/MALE ADAPTER TO POWER SUPPLY *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE FEMALE/FEMALE EXTENSION CABLE REV1.0
© Copyright 2025 ExpyDoc
