Pro-LIFT G5W/G5L Assembly Booklet

Thank you for purchasing a Pro‐LIFT G5. The Pro‐LIFT product line is designed to enhance your interactive whiteboards and projectors or LCD. Please follow all assembly instructions correctly to provide optimal use. Only a qualified contractor should install the Pro‐LIFT G5. If you do not understand any of the assembly instructions, please contact your local re‐seller or visit www.proliftstand.com. IMPROPER INSTALLATION CAN CAUSE DAMAGE TO YOUR Pro‐LIFT AND LEAD TO SERIOUS PHYSICAL INJURY. JORO Manufacturing cannot take any responsibility for damage or injury resulting from improper installation. Do not operate Pro‐LIFT G5 if there are any obstructions below or above the board. Doing so may cause unit malfunction or lead to serious physical injury. The supplied mounting hardware is for use on the Pro‐LIFT stands only. If you encounter any problems or insufficient hardware during installation, please contact your local re‐seller.
6x
ProLift G5 - G5W ASSY Instructions : 0.002
16x
18x
4x
www.joromfg.com
4x
3/16" T-Handle Allen Key
5/16" Washer
8x
LCD Mount Fastener Kit
4x
4x
www.proliftstand.com
Wire Mgmt Molding
5/16x1-1/2" Button Head
M6 x 20mm Socket Cap Screw
Low Profile
Board Backer Support
2x
6x
1x
5/32" Allen (Hex) Key
1x
5/32" Allen (Hex) Key
5/16x3/4" SILVER Button Head
M6 x 20mm Socket Cap Screw
Low Profile
M6x8mm SILVER Button Head
8x
Nylon Washer
1/4" Washer
4x
5/16 Hex Nut
4x
M6 Hex Nut
8x
M6 x 20mm Socket Cap Screw
Low Profile
1x
3/16" Allen (Hex) Key
8x
JORO Button Head
M6x8mm SILVER Button Head
1x
5/32" Allen (Hex) Key
G5 Main Frame Kit
(ONLY available with G5L & G5L-PRO Models)
(ONLY available with G5W & G5W-PRO Models)
WB Fastener Kit
Machine Screw Insulator
6x
Note: Parts may not be exactly as shown and not to scale
COPYRIGHT 2014
Pro-LIFT G5 Foot
Pro-LIFT G5 Foot
1 5/16x1-1/2" Button Head
Mount the Pro-LIFT G5 Feet
For ease of installation, do this step while Pro-LIFT G5 is lying down
Be sure to use the 5/16x1-1/2" Button Head screws provided
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
M6 x 20mm Socket Cap Screw
2 Turret Head
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
Mount the Turret Head
Be sure to use the M6 x 20mm Socket Cap Screws (Low Profile) provided
Be sure to NOT over tighten
If necessary, loosen 5/16x1" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
3 Pro-LIFT G5 Accessory Shelf
Part#: WF122412PROL
M6 x 20mm Socket Cap Screw
5/16x1-1/2" Button Head
5/16x1-1/2" Button Head
Mount the Pro-LIFT G5 Accessory Shelf
Be sure to use the M6 x 20mm Socket Cap Screws supplied
Be sure to NOT over tighten
If necessary, loosen 5/16x1-1/2" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
4 Machine Screw Insulator
Machine Screw Insulator
1/4" Washer
1/4" Washer
M6 x 20mm Socket Cap Screw
M6 x 20mm Socket Cap Screw
Mount the Pencil Tray Adapters (may not be exactly as shown)
Be sure to use the following supplied parts:
1. M6 x 20mm Socket Cap Screw
2. 1/4" Washer
3. Machine Screw Insulator
Do not completely tighten fasteners until pencil tray has been fastened
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
M6 Hex Nut
1/4" Washer
5 WB Hanger
Part#: G5-ACC-WBH
M6 Hex Nut
1/4" Washer
M6 x 20mm Socket Cap Screw
M6 x 20mm Socket Cap Screw
5/16x3/4" SILVER Button Head screw
Be sure to tighten on both angles
once WB Hanger has be installed.
Mount the WB Hanger
BE AWARE the mounting position of the WB Hanger is dependant on projector/white
board combination
Be sure to use the following supplied parts:
1. M6 x 20mm Socket Cap Screw
2. 1/4" Washer
3. M6 Hex Nut
Once the WB Hanger is installed, thighten the 5/16x3/4" SILVER Button Head screws
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
6 3/8" x 4" Lg. - 5/16" Hex Socket Head Shoulder
3/8" Washer
Laptop Tray Arm
Nylon Washer
5/16" Washer
5/16" Nylon Locking Nut
Mount the Laptop Tray Arm (if the Laptop Tray was ordered with your product)
Be sure to use the fasteners supplied
Be sure to remove the 5/16" Nylon Locking Nut prior to mounting the
Laptop Tray Arm
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
7 M6x8mm SILVER Button Head
Laptop Tray
M6x8mm SILVER Button Head
M6 x 20mm Socket Cap Screw
Mount the Laptop Tray (if ordered with your product)
Laptop can slide in/out by loosening the M6 x 20mm Socket Cap Screws
REMEMBER to tighten screws, but DO NOT over tighten
Be sure to use the fasteners from the LTT Kit
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
8 Mounting patterns for tested projectors
Match holes in the diagram to projection system being used
Fasten projector to the corresponding holes using the
JORO Button Head Screws supplied
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
Mount the white board
Use the holes which correspond to manufacturers
recommended projector to image distance
Fasten using the JORO Button Head screws supplied
Be sure to NOT over tighten
Note, there are drilled/tapped holes on the frame
upright, if lowering the board is required
9 JORO Button Head
Mount the Wire Mgmt Molding
JORO recommends attaching the
Wire Mgmt Moldings supplied
Mount the Board Backer Support
Remove the backing from the double
sided tape and attach to side of frame
upright
Remove the backing from the
double sided tape and attach to
outer edge of upright
JORO recommends attaching the
Board Backer Supports supplied
Board Backer Support
Wire Mgmt Molding
Laptop Tray (if ordered with your product)
www.joromfg.com
ProLift G5 - G5W ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
10 Page Left Blank On Purpose
Pro-LIFT G5 Foot
Pro-LIFT G5 Foot
1 5/16x1-1/2" Button Head
Mount the Pro-LIFT G5 Feet
For ease of installation, do this step while Pro-LIFT G5 is lying down
Be sure to use the 5/16x1-1/2" Button Head screws provided
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
2 Pro-LIFT G5 Accessory Shelf
Part#: WF122412PROL
M6 x 20mm Socket Cap Screw
5/16x1-1/2" Button Head
Mount the Pro-LIFT G5 Accessory Shelf
5/16x1-1/2" Button Head
Be sure to use the M6 x 20mm Socket Cap Screws supplied
Be sure to NOT over tighten
If necessary, loosen 5/16x1-1/2" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
Pro-LIFT LCD ARM
3 5/16x3/4" SILVER Button Head
Pro-LIFT LCD ARM
5/16x3/4" SILVER Button Head
Pro-LIFT LCD ARM
Remove Pro-LIFT LCD Arms
Remove 5/16x3/4" SILVER Button Head screws and store in safe
place to re-use once LCD is installed.
Remove Pro-LIFT LCD Arms
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
5/16x3/4" SILVER Button Head
5/16" Washer Narrow
4 G5-ACC-PT5
5/16x3/4" SILVER Button Head
5/16" Washer Narrow
Fasten the 5/16x3/4" SILVER Button Head to the G5-ACC-PT5
800 VESA
600 VESA
400 VESA
200 VESA
200 VESA
400 VESA
600 VESA
800 VESA
Be sure to NOT over tighten
Fasten the G5-ACC-PT5 tubes to your LCD using the
fasteners from the LCD TV Kit.
Be sure to use the fasteners supplied in the LCD TV Kit
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
5 5/16" Washer Narrow
5/16 Hex Nut
Pro-LIFT LCD ARM
Pro-LIFT LCD ARM
5/16 Hex Nut
5/16" Washer Narrow
G5-ACC-PT5
(attached to LCD)
5/16 Hex Nut
5/16" Washer Narrow
Mount the Pro-LIFT LCD Arms to G5-ACC-PT5 tubes on the LCD
Mount the Pro-LIFT LCD Arms prior to hanging on the Pro-LIFT G5L
Be sure to use the fasteners supplied
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
Pin
6 Pin
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
Hang the LCD Assembly
Be sure to hang on all four (4) pins on uprights
If necessary, loosen the 5/16x1" Button Head screws to align holes
REMEMBER to tighten screws, but do NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
7 5/16x3/4" SILVER Button Head
5/16x3/4" SILVER Button Head
Secure Pro-LIFT LCD Arms to Pro-LIFT G5L Frame
Be sure to use the 5/16x3/4" SILVER Button Head screws that were removed earlier
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
8 3/8" x 4" Lg. - 5/16" Hex Socket Head Shoulder
3/8" Washer
Laptop Tray Arm
3/8" Nylon Washer
5/16" Washer
5/16" Nylon Locking Nut
Mount the Laptop Tray Arm (if the Laptop Tray was ordered with your product)
Be sure to use the fasteners supplied
Be sure to remove the 5/16" Nylon Locking Nut prior to mounting the
Laptop Tray Arm
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
9 Laptop Tray
M6x8mm SILVER Button Head
M6x8mm SILVER Button Head
M6 x 20mm Socket Cap Screw
Mount the Laptop Tray (if ordered with your product)
Laptop can slide in/out by loosening the M6 x 20mm Socket Cap Screws
REMEMBER to tighten screws, but DO NOT over tighten
Be sure to use the fasteners from the LTT Kit
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
10 Cable Tray
#12 x 5/8" Pan Head Wood Screw
Mount the Cable Tray (if ordered with your product)
Be sure to use the #12 x 5/8" Pan Head Wood Screws supplied
Be sure to NOT over tighten
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
11 Wire Mgmt Molding
Laptop Tray
(if ordered with your product)
Mount the Wire Mgmt Molding
JORO recommends attaching the
Wire Mgmt Moldings supplied
Remove the backing from the double
sided tape and attach to side of frame
upright
www.joromfg.com
ProLift G5 - G5L ASSY Instructions : 0.001
www.proliftstand.com
COPYRIGHT 2014
12

Download Report