ROUND 2 - TRUCK QUESTION PAPER The alternatives highlighted in Green are correct The alternatives highlighted in RED are not correct T-001 What does the image stand for A. B. C. D. TURBO BOOST ACTIVATED TOW HOOK HINGE CONNECTED FORWARDGEARENGAGED RIDE HEIGHT Reference:- IMPACT Identity 130522206 T-002 Which among the following work using PWM type of Signal? A. B. C. D. VCB Valve AVU Valve Engine Cooling Fan Air Drier Reference:- IMPACT Identity 131653169 T-003 Which of the below statements are true regarding FM 8x4 TIPPER with chassis ID 8 871105? A. B. C. D. Y06 is connected to A17 PB18 Y31 is activated by A17 S49 is connected to LC2:2 A17:PA11 is connected to K03:85 Reference:- WIRING Diagram TP20177407 T-004 What is the expansion for TESP? A. B. C. D. Trucks Extended Service Platform Telematics Extended Service Platform Trucks Extended Service Program Telematics Extended Service Program Reference:- IMPACT Identity 132420038 T-005 Which of the following statements are true A. Engage the differential lock directly before coming onto the slippery surface and disengage the differential lock when the slippery surface has been passed. B. A forewarning of upcoming maintenance is displayed when 90% of the pre-defined values are reached C. A service reminder can be activated by Engine hours, kilo meters or Number of days D. The first stage diff-lock can be engaged without pressing the clutch. Reference:- DRIVER Handbook FMx T-006 Which of the below statements are true regarding Engine oil pressure sensor failures on FM truck? A. Oil contamination was happening in the cable harness due to the sensor part number 21634021. B. Oil contamination was happening in the cable harness due to the sensor part number 21302639. C. If the newly fitted pressure sensor 21634021 fails due to contamination we need to replace sensor along with adaptor 22205127 D. The new sensor part number is 21634021. Reference:- IMPACT TSB V-28-156 T-007 The part no: 22020792 is a A. Special Fuse B. Monostable Flexible Switch C. Bi-metallic strip D. A Sensor Reference:- YVD - BODY Builder Instructions - Chapter 4 Electricity - Vehicle Electronics FM(4) FH (4), Pg No 39 T-008 Which of the following statements are True regarding 85110489 A. B. C. D. Cannot be operated unless parking brake is on. It is applicable for FH / FM Operation is controlled by MID 128. A main switch is also installed inside the cab as a back-up safety stand-by. Reference:- YVD - Accessories Installation Instructions / Accessories Products / Accessories - Trucks/ Cab Exterior / Electrical Cab tilt FM/FH T-009 If A+ B = 9999191,then A and B are A. B. C. D. Different templates of Breakout boxes Different Gauges of a tool Inner Diameter & Outer Diameter of the Shaft Sum of distances measure using the tool Reference:- IMPACT Identity 130522206 T-010 Which among the following are Correct regarding a 4-Way Circuit Valve fitted in a Truck with Chassis id 8913808. A. The opening pressure of Front Brake Circuit is 89.9 ~ 94.27 psi B.The opening pressure for Extra Equipment Connection is 620-650kPa C. The Part No of the 4-Way Circuit Valve is 20452152 D. The opening pressure for Port No 23 is 550 ~ 580 kPa Reference Impact id:129357507 T-011 In FM 400 to avoid stone hitting at the bottom of the fuel tank,an adapter bracket with part number 21451557,was introduced.After installation of this adapter,the ground clearance was increased to an additional ..mm ,which reduced the frequency of stone hitting. A. 100 B. 110 C. 120 D. 130 Reference:-Gyan Weekly Parts Bulletin - Issue No 38-11 T-012 Which of the following statements are correct with regards to the assembly with Part No 21754754 A. B. C. D. Measured pinion bearing pre-load should be between 1250-5500gms Backlash should be between 0.0008 - 0.02cm Thrust screw to be loosened 180°away from crown wheel A protocol is required to be used mainly when performing an overhauling operation Reference:-IMPACT Identity 131274590 & 132379986 T-013 What is true about Ad Blue A. B. C. D. Need to fulfill ISO 22241-1 standard Quality of Ad Blue solution can be checked by special tools 88890105 & 88890110 Refractive index at 20°C should be between 1.3814 - 1.3843 Ad Blue must be stored in direct sunlight to avoid crystallization Reference:-IMPACT Identity 132607548 + 132492215 T-014 You are diagnosing high fuel consumption problem in a vehicle with VIN YV3R6K72398130959 .Which of the following statements are correct? A. B. C. D. Should not diagnose the problem for those buses which are covered less than 50000 Km Fuel Consumption calibration value must be between -10% to +10% Rectifying a low power condition will often remedy the high fuel consumption Check first whether the vehicle has been in the workshop previously and which checks and repairs have been carried out Reference:-IMPACT Identity 103416434, & VTT/Parameter ID AIZ data range T-015 For a vehicle with VIN YV3T2T327D8161427 which of the following statements are valid? A. B. C. D. The accumulator stabilizes the bogie axle by absorbing pressure shocks The Tag Axle starts moving when the Front Axle deviation angle is Greater than 5 degrees Launch Control is an available feature I Roll is enabled only when CC is inactive Reference:- YVD/ View Vehicle Specification for identifying Gearbox variant, IMPACT Identity 131334595, Parameter ID NUO, &IMPACT Identity 121545625 T-016 For a tire with size 295/80R22.5 which of the following statements are correct A. The normal section height is 85% of 236. B. The loaded section height is 80% of 295 C. In axles with single mounted tire, tire pressure in the range 4.5 Bar to 9.0 bar can carry axle load in the range 4 tons to 7.5 tons D. In axles with twin mounted tire, tire pressure in the range 5.8 Bar to 9 bar can carry axle load in the range 8000kg- 12000kg THIS QUESTION IS DELETED T-017 What does ADR stand for? A. B. C. D. Accident Data recorder European Agreement concerning the international carriage of dangerous goods by road Alcolock Drive Extra Safety equipment Reference:-Impact/ Abbreviations T-018 DWS has the following functions A. B. C. D. Lane Departure Warning Forward Collision Warning Headway monitoring and warning Pedestrian callout warning Reference:-YVD/ Accessories Products/ Accessories Buses/ Safety/ Driver Warning System T-019 Which of the following coolant is used in Indian Market? A. B. C. D. 1089238 85109800 85109814 1089328 Reference:- IMPACT/VIPS T-020 What is the package quantity of compressor oil 1161629? A. B. C. D. 125 ml 250 ml 100 ml 1.25 Ltrs Reference:- LDS T-021 Which of the following pay codes are used in LDS for cost price based spare parts booking? A. B. C. D. 0,9,1,2,7 1,7,9,31 1,7,9 9,10,11,21,31 Reference:- LDS T-022 As per DOS, the organization chart A. B. C. D. Shall be defined by Main and Sub Locations Should be Updated and show authorized position titles Should be Approved by General Management Be Maintained and communicated Reference:- DOS Manual/Binder T-023 Which of the following policies are not part of the DOS requirement A. B. C. D. E. F. Quality, Safety & environment Personnel Policy Computer use policy Business operational Customer Complain policy None of the above Reference:- DOS Manual/Binder T-024 FM vehicle reported for a differential failure on 15-02-14 Condition : Vehicle Date Of Delivery is 15-01-2013 ,100000 Km and 11500 Engine hours covered A. B. C. D. Replacement to be done on chargeable basis Replacement can be done against parts warranty if the failure is genuine Vehicle covered only 1 lakhs km and If the failure is genuine you can replace the parts under driveline warranty Replacement can be done against normal warranty Reference:- Warranty clause in warranty binder/Black binder page no 8 T-025 What does K factor denotefor a tipping cylinder A. B. C. D. Distance base tube to inlet port Dimension trunion pin to eye Dimension width of the base tube Dimension base tube bottom to trunion pin Reference:-HYVA PRODUCT INFORMATION 71556299 page no 1/2 T-026 Which statement from the following correctly describes the objectives of Volvo Trucks and Volvo Buses for recall campaigns? A. Vehicles affected must be rectified in accordance with the following: 60% within 3 months 80% within 6 months 90% within 9 months 100% within 12 months B. There are no specific objectives other than it must be carried out as soon as possible. C. Vehicles affected must be rectified in accordance with the following: 60% within 4 months 80% within 8 months 90% within 12 months 100% within 16 months D. 60% within 6 months 80% within 12 months 90% within 16 months 100% within 20 months Reference:- Warranty Binder - 3.1.2