PolycomVVX IP Serie

PolycomVVX IP Serie Manuelle Neukonfiguration Dokumentenversion 1 Polycom VVX IP Serie - Manuelle Neukonfiguration
Copyright Hinweis
Copyright © 2015 finocom AG
Alle Rechte vorbehalten.
Jegliche technische Dokumentation, die von der finocom AG (Placetel) zur Verfügung gestellt wird
ist urheberrechtlich geschützt und proprietär.
Die Veröffentlichung dieses Dokumentes unterliegt der Geheimhaltungsvereinbarung der finocom
AG (Placetel).
Kein Teil dieser Veröffentlichung darf ohne ausdrückliche schriftliche Genehmigung der finocom AG
(Placetel) dupliziert, kopiert, weitergegeben oder in irgendeiner anderen Form zugängig gemacht
werden.
Die finocom AG (Placetel) behält sich das Recht vor, Änderungen ohne vorherige Ankündigung
vorzunehmen.
Schutzmarken
Alle in diesem Dokument erwähnten Produktnamen können Warenzeichen oder eingetragene
Warenzeichen der jeweiligen Firmen sein und werden hiermit anerkannt.
PLACETEL UC-ONE – POLYCOM VVX IP SERIE– MANUELLE NEUKONFIGURATION
©
2015 FINOCOM AG / PLACETEL
SEITE 2
1
Polycom VVX IP Serie – Manual Reconfiguration Procedure
WARNING: THIS PROCEDURE DESCRIBES HOW TO MANUALLY RECONFIGURE
A POLYCOM SOUNDPOINT IP DEVICE TO WORK ON THE PLACETEL UC-ONE
NETWORK. ONCE THIS PROCEDURE HAS BEEN COMPLETED, ANY PRIOR
CONFIGURATION SETTINGS ON THE DEVICE WILL BE OVERRIDDEN,
INCLUDING THE ADMINISTRATOR PASSWORD, AND THE DEVICE WILL ONLY
BE USABLE ON THE PLACETEL UC-ONE NETWORK. THE DEVICE MUST BE
RETURNED TO THE POLYCOM FACTORY DEFAULT CONFIGURATION BEFORE
IT CAN BE USED ON ANY NETWORK OTHER THAN PLACETEL UC-ONE.
Reset the phone to Factory Defaults before continuing.
For VVX Series Models: 300/310, 400/410, 500, or 600
1.
Press the Menu button
2.
Select Settings...
3.
Select 2. Advanced...
4.
At the password prompt, enter key in 456 then press the Enter soft key
Notes:
!
If the password is a known value other than 456, then enter that value instead
!
If the password is not 456 and the actual password is not known, then the
remainder of this procedure cannot be performed, and the device cannot be
modified for use in the Placetel UC-One network.
5.
Select 1. Admin Settings...
6.
Select 1. Network Configuration...
7.
Using the up/down arrows, highlight Provisioning Server... then press Select
8.
Using the up/down arrows, highlight DHCP Menu: ... then press Select
9.
Using the up/down arrows, highlight Boot Server: ... then press Select
10. Using the up/down arrows, select Static then press Select
11. Press Back to exit DHCP menu
12. Using the up/down arrows, highlight Server Type:... then press Select
13. Using the right/left arrows, select HTTPS then press the Ok soft key
PLACETEL UC-ONE – POLYCOM VVX IP SERIE– MANUELLE NEUKONFIGURATION
©
2015 FINOCOM AG / PLACETEL
SEITE 3
14. Using the up/down arrows, highlight ServerAddress:... then press Select
15. Using the numeric keypad, enter the following case sensitive URL:
https://polycom.broadcloud.eu
Notes:
● Use the * key to enter periods (requires a single key press in any key mode)
16. Press the Ok soft key
17. Press Back/Left twice to reach the Save Config screen
18. Press the Yes soft key to begin the reboot sequence
Once the boot process has completed, the device will be provisioned for use in the
Placetel UC-One network. If the station assignment process was properly completed
prior to the reboot, the device will boot into a station specific assigned/usable state. If
not, the device will boot into a default unassigned/unusable state, and will remain in
this state until the site administrator has completed the station assignment process. If
this occurs, contact your site administrator and request that station assignment be
completed for the device in question.
PLACETEL UC-ONE – POLYCOM VVX IP SERIE– MANUELLE NEUKONFIGURATION
©
2015 FINOCOM AG / PLACETEL
SEITE 4
Placetel UC-One ist ein Dienst der
finocom AG
Gustav-Heinemann-Ufer 58
50968 Köln

Download Report