TS 100 TS 200 TS 300

Something about economics …
Gebo Seal Thread Sealants:
Some information about the reach of 50 ml Gebo Seal bottles:
simple
TS 100 = up to 400 ± 20 applications for threads 1/2" (DN 15)
safe
smart
TS 200 = up to 350 ± 20 applications for threads 1/2" (DN 15)
TS 100
TS 300 = up to 300 ± 15 applications for threads 1/2" (DN 15)
Seal thread of prime quality made of
brass, bronze, stainless steel.
Up to 400 ± 20 threads 1/2"
Some technical Technical Data:
Basis material: Polyglycol Dimaethacrylate
Max. thread diameter 1 1/2"
Instant sealing
PURPOSE: Anaerobic thread sealant designed for seals and
sealing of threaded compounds of metal pipes and fittings.
Liquid Thread
Sealants
TS 200
PRECAUTIONS: May cause eye, skin and respiratory tract
irritation. In case of eye or skin contact, flush with water.
Get medical attention if symptoms occur. Please contact
supplier for MSDS. Keep out of reach of children.
Seal thread of good quality made of
brass, bronze, stainless and carbon steel,
aluminum and its alloys.
STORAGE: Store in a cool, dry place at a temperature of
+8 to +28 °C. Protect from direct sunlight.
Keep away from sources of sparks and fire, avoid contact
with moisture.
Shelf life is 24 months from date of manufacture.
Max. thread diameter 1 1/2"
TS 100
TS 200
TS 300
Up to 350 ± 20 threads 1/2"
Sealing within 5–10 min.
TS 300
le
p
s im
Seal thread of rough quality
made of cast iron, carbon
steel or any other metal.
Up to 300 ± 20 threads 1/2"
Max. thread diameter 3"
Instant sealing
Gebo Armaturen GmbH · Am Damm 4 · 58332 Schwelm
Fon 00 49(0)23 36 / 92 85-0 · [email protected] · www.gebo.de
Stand: 01 / 2014
FEATURES: Waterproof, fast hardening, operating temperature range –50 to +150 °C, resistant to atmospheric and
chemical influences and UV rays, suitable for drinkable
water.
fe
a
s
rt
a
sm
Gebo Seal
For which material Gebo Seal is suitable ?
The liquid Thread Sealant for sealing threaded
compounds of metal pipe and
fittings.
Gebo Seal can be used for the following types of metal
threads:
Stainless steel
Table of Application
Gebo
Seal
Type of
material
Quality
of thread
DN
max
Sealing
time
TS 100
Brass
Bronze
Stainless Steel
Prime
40
instant
TS 200
Brass
Bronze
Stainless and Carbon Steel
Aluminum and its alloys
Fine
40
5 ÷ 10
min.
TS 300
Cast Iron
Carbon Steel
Any other metal
Rough
80
instant
Brass
Bronze
Carbon steel
Cast Iron
Aluminum and its alloys
Caution: Time of full curing is 24 hours
Characteristics:
Forget about the „old fashion“ ways of
sealing threads !
All Gebo Seal Products are high resistant against most
chemicals and acids so it can be used also in industrial
sector.
Gebo Seal is suitable for drinking water application.
How to Use Gebo Seal ?
Shake the sealant thoroughly before use.
Thread surfaces should be clean, dry and free of grease.
Apply sealant at least 1/2 of
the length of single-stranded
thread.
Put sufficient quantity of
sealant to fill all engaged
threads. Assemble in a
normal way by using a
wrench.
Within about 1 minute after
application on thread it is possible to manipulate and
change slightly a position of fitting/valve without losing a
sealing effect.
Why ?
Using hemp or sealing tapes for thread sealing could cause
the following effects:
If you are using too much material, the thread could be
damaged during tightening process
Why three different versions of Gebo Seal ?
If you are using not enough sealing material, there could
be leakages. In this case you have to do the installation
process again.
The three different sealants TS 100, 200 and 300 based on
the same principle: All products are anaerobic pipe thread
sealant.
With the new Gebo Seal, the above mentioned problems are
solved:
But the viscosity and the strength are different and
specifically tailored for varying applications.
simple
Reason for this is that we are finding different quality of
threads of different products, a fact that depends on the
material and also on production process.
safe
smart
Gebo Seal is not to be understand as glue or a seal locker,
it’s a thread sealer! After usage of Gebo Seal, a demounting
of the installed products is possible without any problems.
If you might need to disassemble a thread connection
sealed with Gebo Seal, use a normal wrench and simply
turn the fitting opposite direction than assembled.
You do not need to heat the pipe and fitting before.
Opening torque is just a few Nm higher than torque used
to close the thread connection.
Disconnected fitting/valve can be connected to the pipe
again if you clean residuals of cured sealant from its
thread by using a sharp metal object (thick needle, steel
wire).
For the next assembling of disassembled fitting/valve it is
recommended to use TS 300 thread sealant as the quality
of surface of thread become worse.

Download Report