Quick Start Guide LINEARdrive 100/M (LIN100M1) Installing and configuring LINEARdrive 100/M 361 mm / 14.21” A Mounting the LINEARdrive Pay attention when connecting the LED groups: polarity reversal results in no light output and often damages the LEDs 4 LED groups, 4 control channels LedSync out + 120-277 VAC DALI { { DMX in shield DMX in DMX in + LedSync out LedSync out shield N L R G B W R R R R Common anode + + - 12V / 24V DIP switch 24V Ext in Ext in + 1 AWG 20-16 0.5-1.5 mm 2 1 2 12V Non functional AWG 24-16 0.2-1.5 mm 2 2 9 mm 0.35 inch B 9 mm 0.35 inch Making the wire connections and setting the voltage C Configuring the LINEARdrive WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing. CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs. © 2011 eldoLED. All rights reserved. V1.1 More product documentation and eldoLED’s terms and conditions are available at www.eldoled.com. Quick Start Guide LINEARdrive 100/M (LIN100M1) Manual configuration Other features 1. Select mode of operation Locking the configuration M + + M (5 sec) (5 sec) Lock driver Set mode - SET MODE / COLR SHOW M - LOCK + / + NO SOFT HARD M DMX display off DALI display off 2. Set LED groups M + + Visual test run LED groups / LED - M 1-1L 2-2L 3-3L 4-4L 2-4L 1-4L + INP - / Test R 1 sec G 1 sec B 1 sec W 1 sec RGBW 1 sec R 1 sec G 1 sec B 1 sec W 1 sec RGBW 1 sec + OFF POTM 10V SWIT M Dimming curve DIM CURV - / + LOG LIN M + + TEST External input EXT - M + RGB RGBW RGBA RRGB RGGB CCWW CWWW display off display off 3. Standalone operation - Colour*- or Standalone operation - Show - or Networked operation - DMX or DALI - Reset to factory defaults M + - + + (5 sec) M M M M Hue Show DMX address Reset - HUE / + SHOW - / + - DMX ADDR 00...20 0...1535 M M M White Speed Network resolution - WHIT / + 0...510 M SPD - - INT / + 0...255 M + NETW RES -99...99 M INT - / + 0...255 M display off display off + - DMX termination TERM + - / + NO ADDR ADDR SET M M Press menu M display off Nr. of ballasts X BAL YES NO M M Network setup NETW / No address Address set 8 BT 16 BT M Intensity Intensity / / 1...512 RE - SET PRES MENU SET M - Interpolation INTERPOL M display off / + display off AUTO MANU - / + OFF VID COLR WHIT GLOW * The colour menu depends on the LED group settings you have selected in step 2. eldoLED Europe bv eldoLED America, Inc. Luchthavenweg 18a 1762 Technology Drive # 226 5657 EB Eindhoven San Jose, CA95110 The Netherlands T +31 40 2054050 USA T +1 408 451 9333 F +31 40 2054058 F +1 408 451 9335 [email protected] [email protected]
© Copyright 2024 ExpyDoc