INSTRUCTION SHEET 0508 INSTRUCTION SHEET 0508 The RUAKURA MK IV RAM PROBE The RUAKURA MK IV RAM PROBE Manufactured For Shoof International Ltd, New Zealand Manufactured For Shoof International Ltd, New Zealand NOTE TESTING The end cap of the probe case incorporates two brass test terminals and a red indicator light. With batteries installed place the probe electrodes in contact with the cap brass terminals. The end electrode must be adjacent to the red dot. When the cap switch is pressed the red dot will light up if the operation is normal. An oscilloscope test (100 ohm load) should show the waveform illustrated on the circuit diagram. This probe is a precision instrument and should be treated with care. The end cap of the probe case incorporates two brass test terminals and a red indicator light. With batteries installed place the probe electrodes in contact with the cap brass terminals. The end electrode must be adjacent to the red dot. When the cap switch is pressed the red dot will light up if the operation is normal. An oscilloscope test (100 ohm load) should show the waveform illustrated on the circuit diagram. 1 SEC 60 1 SEC 500 0.1 mdf 2 mdf BC558 Clean with warm water and soap or milk detergent; never with alcohol or other organic solvents. Never leave the batteries in the instrument for a long period. CIRCUIT DIAGRAM & WAVEFORM 10v or 15v BC558 BC558 22K 22K Insert into anus of ram and raise the switch end of the probe so that the electrode rings are depressed into contact with the prostate gland seminal vesicle complex. Press the switch for a count of four seconds on and four seconds off, and continue until the ram ejaculates. This normally occurs after one to five stimulations. 1K OPERATION Private Bag 522, Cambridge 3450, NEW ZEALAND Ph: +64-7827 3902 • Fax +64-7827 7596 email: [email protected] • website: www.shoof.co.nz Private Bag 522, Cambridge 3450, NEW ZEALAND Ph: +64-7827 3902 • Fax +64-7827 7596 email: [email protected] • website: www.shoof.co.nz INSTRUCTION SHEET 0508 RAM STOP RING 1.8K 1 SEC 500 0.1 mdf 2 mdf Use LITHIUM CR123A 3-volt batteries as used in cameras. Insert batteries with the positive (+) end forward. Negative (-) end towards the end cap. Four batteries are required. MAINTENANCE BC558 22K Clean with warm water and soap or milk detergent; never with alcohol or other organic solvents. Never leave the batteries in the instrument for a long period. 1.8K MAINTENANCE 1 SEC 60 BC558 22K 1K OPERATION Insert into anus of ram and raise the switch end of the probe so that the electrode rings are depressed into contact with the prostate gland seminal vesicle complex. Press the switch for a count of four seconds on and four seconds off, and continue until the ram ejaculates. This normally occurs after one to five stimulations. BATTERIES To adjust this assembly, align the red dots. The rings can then be moved to the desired position. To lock the assembly, rotate the rings so that the dots are apart. A line has been etched on the plexiglass tube, and the stop ring assembly is normally set in this position. CIRCUIT DIAGRAM & WAVEFORM To adjust this assembly, align the red dots. The rings can then be moved to the desired position. To lock the assembly, rotate the rings so that the dots are apart. A line has been etched on the plexiglass tube, and the stop ring assembly is normally set in this position. 10v or 15v STOP RING BC558 Use LITHIUM CR123A 3-volt batteries as used in cameras. Insert batteries with the positive (+) end forward. Negative (-) end towards the end cap. Four batteries are required. RAM BATTERIES 10v or 15v CELLS TESTING This probe is a precision instrument and should be treated with care. 10v or 15v CELLS NOTE INSTRUCTION SHEET 0508 The RUAKURA MK IV RAM PROBE The RUAKURA MK IV RAM PROBE Manufactured For Shoof International Ltd, New Zealand Manufactured For Shoof International Ltd, New Zealand NOTE TESTING The end cap of the probe case incorporates two brass test terminals and a red indicator light. With batteries installed place the probe electrodes in contact with the cap brass terminals. The end electrode must be adjacent to the red dot. When the cap switch is pressed the red dot will light up if the operation is normal. An oscilloscope test (100 ohm load) should show the waveform illustrated on the circuit diagram. This probe is a precision instrument and should be treated with care. The end cap of the probe case incorporates two brass test terminals and a red indicator light. With batteries installed place the probe electrodes in contact with the cap brass terminals. The end electrode must be adjacent to the red dot. When the cap switch is pressed the red dot will light up if the operation is normal. An oscilloscope test (100 ohm load) should show the waveform illustrated on the circuit diagram. Private Bag 522, Cambridge 3450, NEW ZEALAND Ph: +64-7827 3902 • Fax +64-7827 7596 email: [email protected] • website: www.shoof.co.nz Clean with warm water and soap or milk detergent; never with alcohol or other organic solvents. Never leave the batteries in the instrument for a long period. 1 SEC 500 0.1 mdf 2 mdf BC558 MAINTENANCE 1 SEC 60 BC558 22K 22K Insert into anus of ram and raise the switch end of the probe so that the electrode rings are depressed into contact with the prostate gland seminal vesicle complex. Press the switch for a count of four seconds on and four seconds off, and continue until the ram ejaculates. This normally occurs after one to five stimulations. 1K OPERATION Private Bag 522, Cambridge 3450, NEW ZEALAND Ph: +64-7827 3902 • Fax +64-7827 7596 email: [email protected] • website: www.shoof.co.nz CIRCUIT DIAGRAM & WAVEFORM 10v or 15v BC558 STOP RING RAM Use LITHIUM CR123A 3-volt batteries as used in cameras. Insert batteries with the positive (+) end forward. Negative (-) end towards the end cap. Four batteries are required. 1.8K 1 SEC 500 0.1 mdf 2 mdf BC558 22K Clean with warm water and soap or milk detergent; never with alcohol or other organic solvents. Never leave the batteries in the instrument for a long period. 1.8K MAINTENANCE 1 SEC 60 BC558 22K 1K OPERATION Insert into anus of ram and raise the switch end of the probe so that the electrode rings are depressed into contact with the prostate gland seminal vesicle complex. Press the switch for a count of four seconds on and four seconds off, and continue until the ram ejaculates. This normally occurs after one to five stimulations. BATTERIES To adjust this assembly, align the red dots. The rings can then be moved to the desired position. To lock the assembly, rotate the rings so that the dots are apart. A line has been etched on the plexiglass tube, and the stop ring assembly is normally set in this position. CIRCUIT DIAGRAM & WAVEFORM To adjust this assembly, align the red dots. The rings can then be moved to the desired position. To lock the assembly, rotate the rings so that the dots are apart. A line has been etched on the plexiglass tube, and the stop ring assembly is normally set in this position. 10v or 15v STOP RING BC558 Use LITHIUM CR123A 3-volt batteries as used in cameras. Insert batteries with the positive (+) end forward. Negative (-) end towards the end cap. Four batteries are required. RAM BATTERIES 10v or 15v CELLS TESTING This probe is a precision instrument and should be treated with care. 10v or 15v CELLS NOTE
© Copyright 2024 ExpyDoc
