technical data sheet TM THERMALBRANE 6.5 REFLECTIVE FOAM INSULATION HOME & SHED © VAPOUR BARRIER MEDIUM Product Code: TSTB6-30 DECLARED TOTAL SYSTEM R-VALUES Three-in-one reflective insulation, thermal break and vapour barrier for use in roofs and walls. Increase coverage, reduce wastage via the 150 mm flap provided. Made with high-density XPE foam; compression in situ is minimised. The contribution of this product to the total R-value depends on installation and environmental conditions. The R-value will be reduced in the event of the accumulation of dust on upward facing surfaces and in those cavities that are ventilated. METAL ROOF TILE ROOF 22° pitched flat ceiling ventilated 22° pitched flat ceiling unventilated Highly effective in dampening noise. Fibre-free and non-allergenic. Rigorously tested by independent recognised accredited laboratories in compliance with AS/NZS 4859.1:2002/Amdt 1:2006 ensuring all product claims are met. Trade Select CALCULATION REF: 12202 does NOT achieve R0.2 material R-value, as required by the NCC/BCA when a metal framing member directly connects the exterior cladding to the internal lining, or when no ceiling is installed, in a residence or in a conditioned non-residential TM TM THERMALbrane 6.5 building. Where a Thermal Break of R0.2 is required specify and install Trade SelectTM AMETALIN WINTER SUMMER 1.2 R 2.7 CALCULATION REF: 12093 1.4 2.4 RT WINTER RT T SUMMER RT COMMERCIAL OFFICE 5° pitched, 1000mm ceiling . TM THERMALbrEAK 8 Construction CALCULATION REF: 299r381b WINTER SUMMER Walls: Stud Framed Declared Total System R-values for Typical Systems* Trade Select CALCULATION REF: 299w44b has a material R-value of R0.16. When it is incorporated into typical construction systems the following thermal performance can be achieved: TM TM THERMALbrane 6.5 1.4 R 4.5 CALCULATION REF: 299r382b 0.9 2.0 RT WINTER RT T SUMMER RT Brick Veneer CALCULATION REF: 299w371b Double Brick CALCULATION REF: 299w3811e WINTER RT1.2 WINTER RT2.1 WINTER RT2.2 SUMMER RT1.1 SUMMER RT1.9 SUMMER RT2.0 APPLICATION ROOFS WINTER SUMMER Metal Roof 22° Pitched metal roof with flat ceiling ventilated RT1.2 RT2.7 Metal Roof CALC. REF: 12203 22° Pitched metal roof with flat ceiling unventilated RT1.4 RT2.4 Tile Roof 22° Pitched tile roof with flat ceiling unventilated RT1.4 RT2.4 Commercial Office Roof Suspended ceiling at 1000 mm RT1.4 RT4.5 Commercial or Shed Roof 5° metal roof 100 mm ceiling CALCULATION REFERENCE: 299r380b RT1.4 RT3.2 Commercial or Shed Roof 5° metal roof with no ceiling RT0.9 RT2.0 WALLS Steel Stud Framed Wall 90 mm studs RT1.2 RT1.1 Brick Veneer Wall 110 mm brick with 10 mm plasterboard RT2.1 RT1.9 RT2.2 RT2.0 Double Brick Masonry Wall * The contribution of this product to the total system R-value depends on installation and environmental conditions. The R-values will be reduced in the event of the accumulation of dust on upward facing surfaces and in those cavities that are ventilated. DTE-41680-4 TSTB6-30 refle ™ I N S U L A T I O N www.reflexinsulation.com.au tradeselect.co technical data sheet TM THERMALBRANE 6.5 REFLECTIVE FOAM INSULATION HOME & SHED Classification Trade Select TM THERMALbrane 6.5 classifications in accordance with AS/NZS 4200.1:1994 TM PRODUCT Trade Select TM FLAMMABILITY INDEX AS 1530.2-1993 THERMAL BREAK (THERMAL RESISTANCE) ASTMC518 Low Low ≤ 5 R0.16 Value THERMAL PERFORMANCE AS/NZS 4859.1 Compliant DUTY AS/NZS 4200.1:1994 Extra Heavy EMITTANCE AS/NZS 4201.5:1994 REFLECTIVITY AS/NZS 4200.1:1994 TM THERMALbrane 6.5 Classification Bright side: 0.03 Anti-glare side: 0.05 Value Bright side: 97% Anti-glare side: 95% Value RESISTANCE TO WATER PENETRATION AS/NZS 4201.4:1994 High Pass VAPOUR BARRIER ASTM E96 Medium, PROCEDURE B, WET CUP TEST Classification MACHINE DIRECTION TENSILE STRENGTH AS 1301.448s-91 22.7 kN/m Min 9.5 kN/m LATERAL DIRECTION TENSILE STRENGTH AS 1301.448s-91 21.4 kN/m Min 6.0 kN/m MACHINE DIRECTION EDGE TEAR TAPPI T 470 om-89 1432 N Min 65 N LATERAL DIRECTION EDGE TEAR TAPPI T 470 om-89 1045 N Min 65 N RESISTANCE TO DRY DELAMINATION AS/NZS 4201.1:1994 Pass Pass RESISTANCE TO WET DELAMINATION AS/NZS 4201.2:1994 Pass Pass SHRINKAGE AS/NZS 4201.3:1994 < 0.1% < 0.5% SURFACE WATER ABSORBENCY AS/NZS 4201.4:1994 Unclassified Classification PRODUCT CODE: THICKNESS: ROLL SIZE: WEIGHT: TSTB6-30 6.5 mm 1350 x 22.25 m (30m²) 18.2 kg NCC/BCA Compliant Trade Select THERMALbrane 6.5 complies with AS/NZS 4859.1:2002/Amdt 1:2006 and AS/NZS 4200.1:1994, and therefore meets all the requirements of the National Construction Code and Building Code of Australia for insulation and pliable building membranes. TM TM BUSHFIRE ATTACK LEVELS Trade Select THERMALbrane 6.5 complies with AS39592009 Construction of buildings in bushfire-prone areas for use in wall systems BAL – LOW to BAL – FZ. TM TM Total System R-values R-values apply to typical conditions for mainland Australian capital cities and have been calculated by an independent consulting engineer in accordance with AS/NZS 4859.1:2002/Amdt 1:2006. For detailed design of building systems readers are advised to seek advice from a qualified engineer, based on actual site conditions. Reflectivity Trade Select THERMALbrane 6.5 is made with aluminium foil laminates with reflectivity of 97% and emissivity of 0.03 to TM TM WATER VAPOUR TRANSMISSION RATE: 1.4 g/m²• 24hr (23°C, 50% RH) AMETALIN CLASSIFICATION: MEDIUM VAPOUR BARRIER one side and 95% reflectivity and emissivity of 0.05 to the other in compliance to ASTM Standard E 408-71 (Re-approved 2002). Storage This product should be stored undercover in a clean, dry place in the pack provided. Dimensions Trade Select THERMALbrane 1350 mm x 22.25 m (30 m²) TM 6.5 is sold in sizes: TM Specification Notes When specifying state the following: Product Name: Trade Select ThermalBrane 6.5™ TM The insulation to be installed shall be Trade Select ThermalBrane 6.5™ water permeable, fibre free, thermsingle sided reflective XPE foam laminate with anti-glare, emittance bright side 0.03, antiglare side 0.05. Water Vapour Transmission (WVT) 1.4 g/m²•24hr, Vapour Resistance 85.61 MN•s/g, Vapour Barrier Classification: Medium, Water Barrier Classification: High. TM © 2014 Ametalin All Rights Reserved. Ametalin is a division of Amalgamated Metal Industries Pty. Ltd. Product information in this publication and otherwise supplied to users is based on our general experience and is given in good faith, but due to factors outside our knowledge and control which may affect the use of products, no warranty is given or implied with respect to this information or the product itself (other than that on the label) regarding the suitability of the product for any particular purpose. The usage of this and other building membranes will affect moisture migration in the building element. The purchaser should independently determine the suitability of the product for the intended purpose. For large projects with complex air-conditioning and condensation issues, designers may wish to contact our technical department. Amalgamated Metal Industries Pty. Ltd. reserves the right to amend product specifications without prior notice. Information provided is considered to be true and correct at the time of publication. DTE-41680-4 AUSTRALIAN DESIGNED, DESIGNED, AUSTRALIAN OWNED. OWNED. AUSTRALIAN AUSTRALIAN REFLEX INSULATION PTY LTD MANUFACTURED BY: T: 1300 720 185 AMETALIN E: [email protected] W: www.reflexinsulation.com.au 41-43 BirraleeWESTERN Road Regency AUSTRALIA:Park SA 5010 SOUTH AUSTRALIA/NT: BOX 1677, F: +61 8 8347 PO 0915 Box 77, T: +61 8 8347PO0941 Canning Vale DC WA 6970 Salisbury South BC SA 5106 E: [email protected] W: tradeselect.co F: (08) 9467 0570 F: (08) 8284 1293 refle ™ I N S U L A T I O N www.reflexinsulation.com.au tradeselect.co
© Copyright 2024 ExpyDoc