Additional System Applications Expansion & Contraction Roof Systems 125' w/ Panel Rib and Purlins 210' w/ SSR and Purlins Expansion & Contraction Roof Systems Expansion Joint Types to be used when the ridge to eave dimension is exceeded VP Roof Expansion Limits Expansion & Contraction Ridge & Gutter Ridge 160' SSR Gutter 160' PR & SSR (No maximum for PR) Longitudinal (Length) Expansion Expansion & Contraction SSR Fixed Center Line Expansion & Contraction SEE RC61A3 FOR UPPER ROOF ATTACHMENT NOTE: ROOF PANEL SHOULD BE SEAMED BEFORE INSTALLATION OF RHP TRIM e" x f" TAPE MASTIC CONT. (80349) STEPPED ROOF FLASHING (RHP-) 5" e" x f" x 28" TAPE MASTIC (80345) FLEXIBLE FLASHING (80520) r-14 x 1 w" S.S. ROOF STITCH FSNR (57650) 4" O.C. r-14 x 1 w" S.S. ROOF STITCH FSNR (57650) SEE RC34A4 FOR FASTENER AND MASTIC PATTERNS AT (RHP) FLASHING SSR STEPPED EXPAN. JOINT TRIM LESS THAN 25#L.L. Expansion & Contraction PURLIN SUPPORT MEMBER (PSM) OR (PSN-), LOCATE AT MID POINTS IN BAYS 20' AND LESS AND AT 1/3 POINTS IN BAYS GREATER THAN 20' ROOF PURLIN (PSN-) 6 i" PURLINS (PSM-) 8 i" PURLINS 1'-9" HOLD C L 6" 1'-3" i"X 1 i" A307 BOLT TYP. U.N. 6" STEP FRAME 2" MAX. RAFTER BEAM TOP FLANGE ATTACH EA. END OF (PSM-) OR (PSN-) W/ (2) r-14x 1 r" FSNR (55307) A325 CONN. BOLTS PER DESIGN REQ. EXPANSION JOINT FRAME STEP WITH PURLINS S. WELDED STIFFENER WHEN REQ. BY DESIGN Expansion & Contraction Structural Longitudinal Expansion Joint w/ SSR (PR Similar) Mezzanines VP can provide: • Mezzanine Beam s • Bar Joist • • Design for loads into building system Support columns Support beams Joist Mezzanines Concrete Bar Joist Metal Decking Support Beam Mezzanines Mezzanines For areas in high seismic zones locations for diagonal bracing should be considered on as many sides as possible. Mezzanines Input into VP Command Mezzanine Roof Height Changes Roof Height Change Post & Beam Full Frame Piggy Back P&B on Full Frame Roof Height Change Metal Partitions Length Widthwise Partition Width Metal Partitions Length Transverse Partition Width Longitudinal Partition Metal Partitions Partition Metal Partitions Purlin Closure Purlin Depth Trim Angle Partition Panel Partition to Roof Transition Metal Partitions Girt Closure BL Girt Depth Trim Angle Partition Panel Partition to Wall Transition Partition Post Connection Liner Liner Types: • Full Height Liner • Floor to roof • Partial Height Liner • Girt height plus 12” maximum • Wainscot • Terminates under first girt (7’ - 6”) • 4” from Building Line Liner Partial Height Liner Liner Liner Panel Exterior Wall Panel Liner Trim at Columns Liner Exterior Wall Panel Liner Trim at Columns Liner Panel Liner Liner - Wainscot Endwall Roof Extension Soffit is optional Roof/Rake Extension Canopies Canopy Types: • Piggy Back Sidewall Canopy • • Built-Up Eave Canopy BuiltBuilt--Up Below Eave Canopy Built Piggy--Back Canopy Piggy Piggy--Back Canopy Piggy Piggy--back Canopy Piggy Built--Up Canopies Built Facades Closed Vertical Facade at Sidewall Facades Closed Vertical Facade at Endwall Facade Facade Parapet Endwalls Parapet Post Endpost Sidewall Parapet Parapet Post Facade Crane Systems VP can provide: • Design of building and support system • Support system • Brackets • Crane Beams • Channel Cap Crane Systems Rafter Underhung Cranes • Bracket Usually “S” Shape • Cranes up to 10 tons Usually small span, light crane systems Crane Systems Cap Channel Top Running Cranes • Bracket Cranes up to 15 tons Crane Systems Crane Crane Systems Top Running Cranes w/ Stepped Column • • Cranes up to 30 tons Fixed Base columns sometimes required Crane Systems Top Running Cranes w/ Auxiliary Column • 10' - 15' o.c. Cranes over 30 tons Crane Systems Rafter Mono-rail Cranes • Bracket Usually “S” Shape Single rail hoists Skewed Endwalls Skewed Sidewalls Beam required to supports ends of purlins Skewed Sidewall Hangar Buildings Hangar Door Types: • Sliding Door Leaves • With or without door pockets • Bi Bi--Fold Doors • Stack Doors Sliding Hangar Doors Track Support w/ diagonal support, 10' to 15' o.c. C14 Jambs Sliding Hangar Doors Sliding Doors with Pockets Ridge Sliding Door Leaves Door Pocket Section at Sliding Door Header Framing Purlin RF Door Tracks as required Section @Top of Doors Sliding Doors with Pockets Ridge Door Pocket Bi--Fold Hangar Doors Bi Header Support w/ diagonal support to roof purlins 8' to 10' o.c. Header Jambs Actual door opening height per door mfg. Section at Bi Bi--Fold Header Purlin RF Section @ Header Weighing in at 16,000 pounds and measuring 80' x 27', Schweiss bifolds were the choice of several hangars that were part of a Varco Pruden real estate development project at the Morristown Municipal Airport, Morristown, New Jersey. From: http://www.bifold.com/assets/morristown-1.jpg Bi--Fold Door Bi Stacking Hangar Doors Track Support w/ diagonal support to roof purlins 10' to 15' o.c. Header Jambs Section of Stacking Hangar Door Purlin RF HR Channel Position of door in stacked position Section @ Header Support of Masonry Wall / Roof Material NBVP The builder is must supply the actual weight of these materials. The weights on this page are only for reference. WALLS Brick 4" 8" 12" 40 psf 80 psf 120 psf Hollow Concrete Block (Heavy Aggregate) 4" 30 psf 6" 43 psf 8" 55 psf 12 1/2" 80 psf Hollow Concrete Block (Light Aggregate) 4" 21 psf 6" 30 psf 8" 38 psf 12" 55 psf Miscellaneous Window, glass, frame, & sash 8 psf ROOFS Copper or tin 1 psf Corrugated steel See Manufacture 3-ply ready roofing 1 psf 3-ply felt and gravel 5 1/2 psf 5-ply felt and gravel 6 psf Shingles Wood Asphalt Clay tile Slate 1/4" Sheathing Wood 3/4" Gypsum 1" 2 psf 3 psf 9 - 14 psf 10 psf 3 psf 4 psf Insulation (per 1" thick) Loose 1/2 psf Poured-in-place 2 psf Rigid 1 1/2 psf Girt Strapping for Panel NBVP Wall Support Beams Wall Support Beam Masonry or Concrete Flange Brace Support of Masonry • Wind Beam / Wind Girt Carrier / Jack Beams Carrier / Jack Beams Carrier Beams eliminates the need for every other interior column Jack Beam at Sidewall Self--Storage Buildings Self • • Provided by Trachte Building Systems. www.trachte.com Product Features • Galvanized structural • 18 gauge flush jamb and header system with no exposed fasteners • 24 gauge flush hallway systems • Bolted connections on structural Self--Storage Buildings Self Product Features (con’t) • Full height partitions • Door openings are typically 8” wider • Trac Trac--Rite® Door • Sealed bearings, tensioners and stainless steel latch. Self--storage Buildings Self Product Features (con’t) • Wedge anchors and drill bits are included for columns • Sealed foundation plan/Permits Self--storage Buildings Self Structural is prepunched and connections bolted. Jambs are prepunched to receive roll up door. Self--storage Buildings Self VP flush 18 gauge jamb and header system with no exposed fasteners. Self--storage Buildings Self VP unit with full height partitions and galvanized structural. Self--storage Buildings Self VP 20 and 24 gauge flush hallway system with no exposed fasteners. Self--storage Buildings Self Jamb at foundation notch. Notch should overhang by ½” Self--storage Buildings Self Low profile ¼:12 pitch. Self--storage Buildings Self Typical partially climate controlled building. Unlike many competitors, we provide the complete package. Self--storage Buildings Self Self--storage Buildings Self VP Twostory Self--storage Buildings Self Self--storage Buildings Self Self--storage Buildings Self Mike Stanley VP – WI office phone: 608 608--882882-5000 email: [email protected] Hip Roofs Typical Hip Framing Hip Roofs Typical Hip Framing Hip Roofs Difficult Hip Framing Hip Roofs Move frames to line-up Difficult Hip Framing Hip Framing Purlins Frame Hip Clip VPCommand Detailed Connection Hip/Valley Framing Hip Framing Hip Framing Hip Framing Hip Framing Hip and Valley Field cutting of roof panels required
© Copyright 2025 ExpyDoc
