RONDA startech 4000 Multifunctions with Big Date, Alarm, 2nd Time Zone Caliber 4002.B – 12½''' Product Specifications Features Analog quartz movement – Repairable metal watch movement Line startech – Very long battery life Caliber 4002.B Size 12½''' – Power saving mechanism with pullled out stem: Reduction of consumption approximately 70% Version Swiss Made 5 Jewels / gold plated Standard battery life 60 months Hand fitting height 0 Date: 02.08.2016 www.ronda.ch Page: 1 RONDA startech Caliber 4002.B – 12½''' Functions Technical Specifications – Big date Diameter Total 28.60 mm – 2 hands Case fitting 28.00 mm Movement height 4.40 mm Height over standard battery 4.40 mm Movement rest 0.60 mm Height over stem 1.90 mm Length of stem travel 0.90 mm Force to push the stem for screwed crown 10 / 15 N Stem thread 0.90 mm Standard battery 395 Standard battery life 60 months Battery voltage 1.5 V Current consumption – typical 1.19 μA (Date Mechanism not in Gear) Current consumption – maximum 1.65 μA (Date Mechanism not in Gear) Useful torque minute – typical 300 μNm Operating temperature 0 - 50 °C Instantaneous rate -10/ +20 sec/month Resistance to magnetic fields 18.8 Oe Resistance against shock NIHS 91-10 Date: 02.08.2016 www.ronda.ch Page: 2 T2-Instructions 4002.B Fitting dial and hands Movement holder Removing setting stem H5XXX.1T •Crown in position II •Wind crown until date 02 appears •Crown in position III •Wind hour hand forwards until date changes to 03 •Remove working hand •Fit dial •Point all hands towards 12 o’clock •Set time •Crown in position II •Set date •Crown in position I General Instructions Date switching duration: First and tenth digit discs ~2hrs Removing the setting stem can only be effected in Pos. I. The use of supporting screws is essential when mounting the hands. Permitted hand setting strengths: Hr / min. hands: <40N Other hands: <30N During quick date correction (setting stem in position II), a date switching speed of 5 d/s must not be exceeded. Movement holder Setting hands H5XXX.1A DOMVT080e Version:1.6 Creator:5166 Validator:5160 Mai 2015 Werkhalter T2 Porte-pièce T2 Movement holder T2 Verwendung & Übersicht Utilisation & Vue d’ensemble Utilisation & Overview DOMVT004 Version: 2.1 Prozess: 3.1.3 Änd.-Dat.: 20.04.15 5110, 5112, 5150, 5151, 5152, 5160, 5161, 5163, 5164, 5166, 5310, 5311, 5312, RTC, RHK Ermano, Pine Precision AF Switzerland SA, Horotec SA, Tschudin & Schneider Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group ZXX Poser les aiguilles Stellwelle entfernen T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H ZXX.2A H ZXX.1T H ZXX.1A H ZXX.1T H 80XX.1A H 80XX.1T Z50 ZXX Z60 8000-8499 8040.B 8040.N Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 1/9 7000-7999 H 7XXX.1A H 7XXX.1T 700X.B 700X.L 700X.N 700X.P Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 2/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 6000-6999 Poser les aiguilles Stellwelle entfernen T Enlever la tige Alarm-Check P Contrôle d’alarme Hand setting Stem removal Alarm check Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 6XXX.1A H 6XXX.1T 6XXX.B 6XXX.D Swiss Made 4000-5999.B/.C/.D/.E Swiss Parts H 5XXX.1A H 5XXX.1T H 5XXX.1P H 5XXX.FA H 5XXX.1T H 5XXX.1P 4XXX.B 5XXX.B 5XXX.C 5XXX.D 5XXX.E 4000-5999.F 5XXX.F (4XXX.B) (5XXX.B) (5XXX.C) (5XXX.D) (5XXX.E) Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 3/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 3500-3999 Stellwelle entfernen T Poser les aiguilles Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 35XX.1A H 35XX.1T H 106X.1A H 106X.1T 3520.D 3540.D 1062-1069 1062 1063 1064 1069 Swiss Made Swiss Parts 6h 1062 - 1063 - - 1064 - 1069 - 1042 - 6h - - - - - - H 1042.1A H 1042.1T 1042 Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 4/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 1032 Poser les aiguilles Stellwelle entfernen T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 1032.1A H 1032.1T H 101X.1A H 101X.1T H 100X.1A H 100X.1T 1032 1012-1019 1012 1013 1014 1015 1016 1019 1002-1009 1002 1003 1004 1005 1006 1009 Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 5/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 782-788 Poser les aiguilles Stellwelle entfernen T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 78X.1A H 78X.1T 782 783 784 785 788 Swiss Made 772-775 Swiss Parts H 77X.1A H 77X.1T 772 773 774 775 Swiss Made Swiss Parts Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 6/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group Stellwelle entfernen Poser les aiguilles T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 76X.1A H 76X.1T 762-763 762 762E 763 763E Swiss Made Swiss Parts 762 - - 762E - - 763 - 763E 751-753 H 75X.1A H 75X.1T 751 753 751 Swiss Made Swiss Parts - - 753 Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 7/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 712-715 Stellwelle entfernen Poser les aiguilles T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 71X.1A H 71X.1T 712 713 714 715 Swiss Made 702-708 Swiss Parts H 70X.1A H 70X.1T 702 703 704 705 708 (706) Swiss Made 706 Swiss Parts H 706.1A H 70X.1T 706.1 706.2 706.3 706.B Swiss Made 6h Swiss Parts 6h Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 8/9 Zeiger setzen A Kalibergruppe Groupe de calibre Calibre group 582-585 Poser les aiguilles Stellwelle entfernen T Diverses Enlever la tige Divers Hand setting Stem removal Various Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number Artikelnummer Numéro d’article Part number H 58X.1A H 58X.1T H 51X.1A H 51X.1T H 50X.1A H 50X.1T 582 583 585 512-519 512 513 515 517 519 502-509 502 503 505 507 509 Wichtig! Die Höhe der Abstützschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster l’hauteur des vis de support au préalable de chaque série. Important! Adjust height of support screws prior to each series. DOMVT004 / Version: 2.1 / Prozess: 3.1.3 / Änd.-Dat.:20.04.15 Seite 9/9 Technical Instructions 4002.B 2000.577.G Main plate 1. 3305.315.CO Cannon pinion with driver (Aig.0, closed) 2. A 2030.037.CO Centre bridge 3. Centre bridge held by 1 screw 4000.250. 4000.250 Screw 4. 3001.055.FI Sliding pinion 5. 3000.177.CO Setting stem 6. 3017.049 Setting lever 7. 3905.049 Setting lever jumper (3 positions) 8. Setting lever jumper held by 1 screw 4000.250. 4000.250 Screw 9. 3015.081 B Yoke (3 positions) 10. 3905.067 Yoke spring 11. Tensioning the spring arm. 3622.039 Stator (counter 6h, 9h, chrono) 12. 3603.079 Plastic bracket 13. Plastic bracket held by 4 screws 4000.250. 4000.250 Screw 14. 3715.094.RK Rotor 15. C 3147.047.CO Intermediate wheel (chrono) 16. 3136.170.CO Center second wheel (short) 17. 10/2013 N RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1 Technical Instructions 4002.B 3136.148.CO Second wheel (short) 18. 3122.056.CO Third wheel 19. 2020.164.G Train wheel bridge 20. Train wheel bridge held by 3 screws 4000.250. 4000.250 Screw D 21. 3621.079.RK Coil (center) 22. Attention: Please hold the coil only on the grey coil core. Coil held by 1 screw 4000.250. 4000.250 Screw 23. 3603.034 Battery insulator 24. 3503.071 Tube 25. E 3601.118 Contact strip 26. Contact strip held by 1 screw 4000.250. 4000.250 Screw 27. 3503.059 Tube 28. 3503.068 Tube 29. F 10/2013 N RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2 Technical Instructions 4002.B 3612.147.4003 Electronic module 30. Electronic module held by 1 screw 4000.248. Electronic measurements may be realised now. 4000.248 Screw 31. 3603.069 Circuit insulator 32. G 3601.107.G Pusher contact spring 33. 2130.176.G.M01.4002B Electronic module cover 34. Electronic module cover held by 3 screws 4000.250. 3600.010.HGF Battery 395 35. 3601.109.G Bridle + 36. Bridle held by 1 screw 4000.250. 4000.250 Screw 37. H I 10/2013 N RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3 Technical Instructions 4002.B 2000.577.G Main plate 38. 3004.164 Setting wheel 39. 3004.164 Setting wheel 40. 3007.054.CO Minute wheel 41. J 2130.143 Minute train bridge 42. Minute train bridge held by 2 screws 4000.250. 4000.305 Screw 43. 3004.227 Tens indicator driving wheel 44. The short tooth of the tens indicator driving wheel must point to the center of the movement. 3500.075 Tens jumper 45. K 2130.142 Tens jumper maintaining plate 46. Tens jumper maintaining plate held by 2 screws 4000.332. Tensioning the spring arm. 4010.306 Screw 47. 3301.285 Hour wheel (Aig.0) 48. 3315.016 Friction spring 49. 3004.224.CO Date indicator driving wheel 50. 3500.049 Date jumper 51. 10/2013 N RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4 Technical Instructions 4002.B 3504.214.AD.1.A Units indicator (standard) 52. Nick of the indicator at 3 o`clock. 3147.054 Tens intermediate wheel 53. 2130.141 Date indicator maintaining plate 54. Date indicator maintaining plate held by 1 screw 4000.250. 3905.070 Date jumper spring 55. Insert the date jumper spring in the provided opening. 3504.215.AD.1.A Tens indicator (standard) 56. Nick of the indicator at 3 o`clock. 2130.140.G Date mechanism maintaining plate 57. Date mechanism maintaining plate held by 2 screws 4000.250. 4000.250 Screw L 58. 3506.072.G Dial support 59. 8200 Moebius 8200 60. M 9014 Moebius 9014 61. 124 Jismaa 124 62. 9020 Moebius 9020 63. 10/2013 N RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5 4002.B Electronic measurements Battery 395 Voltage 1.55 V Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption: Typical consumption Maximal consumption Rate Lower working voltage limit 1.19 µA 1.65 µA -10s/M. .. +20s/M. 1.20 V Setting stem in position III, 60 s measuring interval: Typical consumption Maximal consumption 10/2013 0.10 µA 0.30 µA RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1 4002.B Electronic measurements Coil resistance M1 2.20 kΩ .. 2.40 kΩ Coil isolation M1 10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] ∞ kΩ EM 2 Technical Instructions 4002.B 2000.577.G Main plate 1. 3305.315.CO Cannon pinion with driver (Aig.0, closed) 2. A 2030.017.CO Centre bridge 3. Centre bridge held by 1 screw 4000.250. Parts 2030.017.CO, 3004.223 and 3500.059 must be exchanged together. 4000.250 Screw 4. 3001.055.FI Sliding pinion 5. 3000.177.CO Setting stem 6. 3017.049 Setting lever 7. 3905.049 Setting lever jumper (3 positions) 8. Setting lever jumper held by 1 screw 4000.250. 4000.250 Screw 9. B 3015.081 Yoke (3 positions) 10. Parts 3015.081 and 3905.067 must be exchanged together. 3905.067 Yoke spring 11. Tensioning the spring arm. Parts 3015.081 and 3905.067 must be exchanged together. 3622.039 Stator (counter 6h, 9h, chrono) 12. 3603.079 Plastic bracket 13. Plastic bracket held by 4 screws 4000.250. 4000.250 Screw 14. 3715.094.RK Rotor 15. C 3147.047.CO Intermediate wheel (chrono) 16. 3136.170.CO Center second wheel (short) 17. 10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1 Technical Instructions 4002.B 3136.148.CO Second wheel (short) 18. 3122.056.CO Third wheel 19. 2020.164.G Train wheel bridge 20. Train wheel bridge held by 3 screws 4000.250. 4000.250 Screw D 21. 3621.079.RK Coil (center) 22. Attention: Please hold the coil only on the grey coil core. Coil held by 1 screw 4000.250. 4000.250 Screw 23. 3603.034 Battery insulator 24. 3503.071 Tube 25. E 3601.118 Contact strip 26. Contact strip held by 1 screw 4000.250. 4000.250 Screw 27. 3503.059 Tube 28. 3503.068 Tube 29. F 10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2 Technical Instructions 4002.B 3612.147.4003 Electronic module 30. Electronic module held by 1 screw 4000.248. Electronic measurements may be realised now. 4000.248 Screw 31. 3603.069 Circuit insulator 32. G 3601.107.G Pusher contact spring 33. 2130.176.G.M01.4002B Electronic module cover 34. Electronic module cover held by 3 screws 4000.250. 3600.010.HGF Battery 395 35. 3601.109.G Bridle + 36. Bridle held by 1 screw 4000.250. 4000.250 Screw 37. H I 10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3 Technical Instructions 4002.B 2000.577.G Main plate 38. 3004.164 Setting wheel 39. 3004.164 Setting wheel 40. 3007.054.CO Minute wheel 41. J 2130.143 Minute train bridge 42. Minute train bridge held by 2 screws 4000.250. 4000.305 Screw 43. K 3004.223 Tens indicator driving wheel 44. Parts 2030.017.CO, 3004.223 and 3500.059 must be exchanged together. The short tooth of the tens indicator driving wheel must point to the center of the movement. 3500.059 Tens jumper 45. Parts 2030.017.CO, 3004.223 and 3500.059 must be exchanged together. 2130.142 Tens jumper maintaining plate 46. Tens jumper maintaining plate held by 2 screws 4000.332. Tensioning the spring arm. 4010.306 Screw 47. 3301.285 Hour wheel (Aig.0) 48. 3315.016 Friction spring 49. 3004.224.CO Date indicator driving wheel 50. 3500.049 Date jumper 51. 10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4 Technical Instructions 4002.B 3504.214.AD.1.A Units indicator (standard) 52. Nick of the indicator at 3 o`clock. 3147.054 Tens intermediate wheel 53. 2130.141 Date indicator maintaining plate 54. Date indicator maintaining plate held by 1 screw 4000.250. 3905.070 Date jumper spring 55. Insert the date jumper spring in the provided opening. 3504.215.AD.1.A Tens indicator (standard) 56. Nick of the indicator at 3 o`clock. 2130.140.G Date mechanism maintaining plate 57. Date mechanism maintaining plate held by 2 screws 4000.250. 4000.250 Screw L 58. 3506.072.G Dial support 59. 8200 Moebius 8200 60. M 9014 Moebius 9014 61. 124 Jismaa 124 62. 9020 Moebius 9020 63. 10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5 4002.B Electronic measurements Battery 395 Voltage 1.55 V Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption: Typical consumption Maximal consumption Rate Lower working voltage limit 1.19 µA 1.65 µA -10s/M. .. +20s/M. 1.20 V Setting stem in position III, 60 s measuring interval: Typical consumption Maximal consumption 10/2013 0.10 µA 0.30 µA RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1 4002.B Electronic measurements Coil resistance M1 2.20 kΩ .. 2.40 kΩ Coil isolation M1 10/2013 Powered by TCPDF (www.tcpdf.org) RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] ∞ kΩ EM 2
© Copyright 2024 ExpyDoc
