Poster

Poster
1.
Dill S., Schöppner V., Reinders F., Kaya, A. Müller‐Roosen, M. Fleschutz, B. Taube M., Terwolbeck S.,
Wolfring M.
Development of an environmentally safe and health harmless flame retardant polyethylene blown film
2.
Hirsch, U. Teuscher N., Rühl M., Heilmann A.
Antifouling modification of reverse osmosis membranes by plasma processes and radical polymerization
3.
Jablonska M., Hirsch U., Teuscher N., Rühl M., Heilmann A.
Biofouling prevention in membrane modules for water desalination by functional coatings on feed spacer
4.
Nhung, V.
Modified manufacturing porous scaffold based on polyhydroxylbutyrate (PHB) in medicine application
5.
Khanal S., Khadka I., Adhikari R.
Polyaniline/wheat stalk dust composites for effective removal of arsenic (V) from aqueous solution
6.
Khatiwada S. P., Adhikari R., Heinrich G.
Transparent epoxy thermoset toughened by modified star block copolymer
7.
Baral R. N., Khanal S., Wutzler A., Lach R., Grellmann W., Adhikari R.
Urban carpentry waste based natural fibers for preparation of reinforced composites with thermoplastics
8.
Müller‐Roosen M., Weinlein R., Hollosi R., Palagushkina A., Peiffer F.
Development of a wood–plastic composite (WPC) with green wood waste
9.
John R., Trommler K., Schreiter K., Simon F., Siegel C., Wagenführ A., Spange S.
New approach for adhesion promotion in natural fiber composites
10.
Wuestenhagen S., Lange O., Voigt M.
Natural fibre composites – Use case light electric vehicle
11.
Schreiber R., Klepek M., Moneke M., Fleischhauer M.
Comparing fracture of carbon fiber–epoxy resin and carbon fiber–polyamide resin composites
12.
Ganß, M. Hartmann C., Barnickel J., Beinersdorf H., Kuhne M., Hildebrand J., Könke C.
Strain monitoring in the adhesive layer of steel–CFK joints using fiber‐optical sensors
13.
Bräuer M., Gedan‐Smolka M., Häußler, L. Kühnert I., Lappan U., Lehmann D., Scheibner H., Schneider K.,
Tuschla M.
Grenzflächenreaktives Spritzgießen von Mehrkomponentenverbunden
14.
Birkner M., Schreiter K., Trommler K., Schuberth A., Lampke T., Spange S.
Twin polymerization of epoxy compounds for new hybrid materials
15.
Tamang S., Shrestha S., Wutzler A., Lach R., Grellmann W., Adhikari R.
Functionalization of nanocarbons for using as fillers with epoxy resin
16.
Nagel K., Kaßner L., Grützner R.‐E., Spange S.
Synthesis of polyamide 6/silica/polysiloxane composites by in‐situ hydrolytic polymerization process
17.
Grala M., Bartczak Z.
Morphology, thermal and mechanical properties of polypropylene/SiO2 nanocomposites obtained by reactive
blending
18.
Dhakal K. N., Khanal S., Lach R., Grellmann W., Heinrich G., Adhikari R.
Conducting polymer nanocomposites using multi‐walled carbon nanotubes in a biogradable polymer matrix
19.
Erdmann R., Zepnik S., Kabasci S., Heim H.‐P.
Influence of different temperatures and strain rates on the mechanical properties of cellulose
acetate/thermoplastic urethane blends
20.
Theumer T., Krombholz A.
Material‐based design and layout of a biopolymer using the example of sports equipment
Seite 1 von 2
21.
Monami A., Lach R., Escudeiro R., Langer B.
Artificial aging of biodegradable mulch films
22.
Schwan S., Theumer T., Petzold W., Menzel M., Krombholz A.
Morphological validation of specimens formed by Fused Filament Fabrication of nylon (PA 6.6)
23.
Kaut F.
Formfaktorermittlung anhand signifikanter Prozessparameter
24.
Schoßig M., Bierögel C., Grellmann W.
Assessment of fracture behavior under impact loading with simultaneous recording of acoustic emission
25.
Märten A.
Umweltsimulation mittels Schwing- und Stoßbelastung
26.
Chang B., Schneider K., Heinrich G.
Structural evolution of isotactic polypropylene during creep: An in‐situ study by synchrotron small angle X‐ray
scattering
27.
Szilágyi C., Seeger P., Moneke M., Stengler R.
In‐situ optical scratch analysis and correlation between tangential force and scratch behavior of thermoplastic
injection molded plates
28.
Archodoulaki V.‐M., Petrica M., Schenkyr J., Örs Ünsal A., Koch T.
The influence of morphological changes induced by different cooling rates on the wear behavior of
thermoplastics
29.
Stratmann P., Klüppel M.
Investigation of carbon black filled acrylonitrile elastomers via dielectric, mechanical and thermodynamic
methods
30.
Xiang F., Schneider K.
Application of J‐integral in the fracture of filled rubber
31.
Lach R., Reincke K., Grellmann W., Heinrich G.
Prediction of crack toughness of rubber under impact loading conditions
32.
Lehmann S.
Studie zum Spreizverhalten von Faserrovings für die Herstellung von unidirektional verstärkten Tapes
33.
Sirch C., Bierögel C., Grellmann W., Frank G., Höhndorf T., Heuert U.
Akustische Defektoskopie an Kunststoffschweißnähten mittels Luft-Ultraschall
34.
Bornemann S, Weiß J..
Oberflächencharakterisierung von Polyesterfolien zur gezielten Optimierung der optischen und funktionellen
Folieneigenschaften
Seite 2 von 2

Download Report