R TP-1201 OPERATION MANUAL THE TP-1201 IS A 12-CHANNEL TOUCH PANEL. EACH CHANNEL HAS TWO CONTROL KEY. ONE FOR LATCH AND THE OTHERIS FOR FLASH. A SWITCH CHASE IS FOR CONTROL LING THE SPEED OF LIGHT. FURTHERMORE, THERE ARE 4 CHANNELS CHASE OF 3 ZONES TO CONTROL 3 SETS OF SIGNAL OUTPUTS AND AUDIO/CHASE SELECTOR. CHASE TO SELECT THE SIGNAL CONTROL BY AUDIO OR AUTOMATICALLY. SPECIFICATIONS: WEIGHT: 0.95 Kg(2.1 lbs) DIMENSION: 48.5x90x33 CM(19"x35"x13") INSTRUCTION: POWER SUPPLY: 1 CONNECT WITH APPROPRIATE DC ADAPTOR 16-25V 500mA OR INSERT TO NO.4 OF 8 PIN DIN SOCKETS FROM REAR WITH +20V. 2 FRONT: 3 4 CHASE AUDIO& POWERSW. 1 MIC R TP-1201 12CHANNEL TOUCH LATCH 1 LATCH LATCH 2 3 LATCH LATCH 4 LATCH 5 6 LATCH LATCH 7 LATCH 8 9 LATCH LATCH 10 ON OFF LATCH 11 1-4 12 AUDIO NOTICE: 5-8 PANEL The3chase keysshould holdfor1sec toreact FLASH FLASH FLASH FLASH FLASH FLASH FLASH FLASH FLASH FLASH FLASH CHASE 9-12 FLASH 5 2 6 1. LATCH KEY: 12 INDICATORS AND TOUCH SWITCHES, FIRST TOUCH THE INDICATOR IS ON, AND THE SECOND IS OFF. 2. FLASH KEY: THE LED OF LATCH IS TURNED ON WHEN TOUCHED, OTHERWISE, IT WILL BE OFF UNTIL RELEASED. 3. CHASE KEY: CONTROL THE SPEED OF LIGHT, UNDER CHASE FUNCTION. 4. CHANNEL SELECTOR : EACH ZONE CONTAINS 4 CHANNELS, EACH ZONE SELECTED BY TOUCH; OTHERWISE RETOUCH WITH 3 SECONDS, IT WILL BE MALFUNCTION 5. AUDIO/CHASE SELECT KEY: IF LED OF AUDIO IS ILLUMINATED, IT WILL BE CONTROLLED BY SIGNAL INPUT. OTHERWISE, IT WILL CONTROL AUTOMATICALLY. 6. AUDIO & POWER SWITCH: TURN ON MAIN POWER AND CONTROL THE SENSITIVITY OF AUDIO SIGNAL. 3 REAR 1 2 4 5 8PINDINPLUGOUTPUTCONNECTIONDIAGRAM CH.9-12 AUDIO EXT INT L EXT.AUDIO INPUT LINEOUT 1VRMS 3 H 2 1 DC20V INPUT + CH11 +20V CH12 CH.5-8 GND CH7 CH10 +20V CH9 CH8 CH12 GND 3 3 CH.1-4 GND CH3 CH6 +20V CH5 CH4 CH11 CH10 GND CH2 CH1 CH9 GND 2 GND CH.1-12 1 24-004-0064 1. AUDIO EXT./INT. SLIDE SWITCH IT WILL BE CONTROLLED BY EXTERNAL SIGNAL WHEN SWITCH TO EXT, OTHERWISE IT WILL BE INTERNAL SIGNAL CONTROL. 2. EXT. AUDIO INPUT FOR EXT AUDIO SIGNAL IN WITH 1V RMS. 3. 8-PIN DIN SOCKET FOR SIGNAL OUTPUT; IT CONNECTS SHOWN AS FIGURE. CH11 GND CH7 GND CH3 GND +20V CH10 +20V CH6 +20V CH2 CH12 CH9 CH8 CH5 CH4 CH1 CH12 CH11 CH10 CH9 GND 3 GND GND 2 1 4. SENSITIVITY OF FINE TRIMMING-POT SELECT THE RANGE OF SENSITIVITY FROM LOW TO HIGH WITH COUNTER CLOCKWISE. 5. EXT. DC INPUT FOR DC 20V. POLARITY OF THE DC JACK SHOWN AS BELOW: - + WARNING 1. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. 2. PUT ON THE DRY AREA. 3. NON-TECHNICAL MAN IS NOT ALLOWED TO OPEN THE CASE.
© Copyright 2024 ExpyDoc