702 58300000176423 Ersatzteilinformation ABZ EN C 3/19/2014 Sparepart information Page 1/3 00628833,00628834,00628836,00751392,00752628,00752647 Installing door spring kits Replacement door spring kits include and installation instructions. (2) door springs • Order one (1) kit per dishwasher, • • Replace Replace selecting with brackets / cord holders, (2) hinge cords door springs with the desired tension. a//parts - do not reuse existing parts. both sides using the same (tension) springs. Spring kits are used for the following Changing spring tensions repairs: for lighter / heavier Doors drifting open / not holding wooden (fully integrated) door panels position Doors closing on their own / failing to stay open Broken cords / holders / springs Kit door springs have a color coded "dot" corresponding to the spring tensions below. spring replacement kits (e.g. 00754873, 00754866) instead of other kits or springs. Wooden Panel Old Spring Color Force Use these Dishwasher Kit # Strom ler t I I I 0'0'659341 ...... Pink 00626664 00752547 Black 00626662 ...... Blue 00626665 0075252:8 Red 0,0'627230 00754392 Use if pink springs Fully integrated aren't stron 9 enough 3- 10kg Fully integrated (6.6- 22 tb.) 2-3kg Fully integrated (4.4 - 6.6 lb.) Use if black springs Evolution / mntegra are too strong ÷ Evolution / mntegra Weaker Replacement spring kits include (2) springs with brackets, (2) cords & instructions -- order one kit (1) per dishwasher. NOTE: Both sides (left / right) must be replaced at the same time using the same springs and cords. Spring tensions must be matched for doors to open / close properly. HINT: Many service calls have occurred from customers with dishwasher doors without wooden panels installed. Door springs are chosen to handle the weight of most wooden panels - doors without panels are too light and close on their own. For authorized servicers, additional assistance is available by contacting our Quickfinder website at http://portal.mch.bsh,q.com/portal. Copyright our Technical Support team at (800) 444-9091 or by visiting by BSH Bosch-und Siemens Hausger&te GmbH This material is intended for the sole use of BSH authorized persons and may contain unauthorized review, use, copying, disclosure, or distribution in any format is prohibited. confidential and proprietary information. Any 702 58300000176423 Ersatzteilinformation ABZ EN C 3/19/2014 Sparepart information Page 2/3 00628833,00628834,00628836,00751392,00752628,00752647 Tools needed: Supplied parts: Installation T20 Torx & #2 Phillips (2) springs w/ brackets screwdrivers, pliers and mallet. / cord holders, (2) cords w/ holders instructions 1. Cord holder 2. 3. Sliding Cord 4. Door spring Replacement cords attach to door springs differently being inserted int._go springs instead of being slid over them. pulley Existing door spring system . . 3. Turn off / disconnect electrical / water supplies slide out dishwasher and remove outer door. To release spring tension, disconnect cords from both hinge leys, cords and door springs from both sides. Reinstall Remove levers. mounting Remove brackets, sliding pul- left and right pulleys. For authorized servicers, additional assistance is available by contacting our Quickfinder website at http://portal.mch.bsh,q.com/portal. Copyright as needed. our Technical Support team at (800) 444-9091 or by visiting by BSH Bosch-und Siemens Hausger&te GmbH This material is intended for the sole use of BSH authorized persons and may contain unauthorized review, use, copying, disclosure, or distribution in any format is prohibited. confidential and proprietary information. Any 702 58300000176423 Ersatzteilinformation ABZ EN C 3/19/2014 Sparepart information Page 3/3 00628833,00628834,00628836,00751392,00752628,00752647 4. . 6. If spring brackets aren't already To install both springs installed into springs, into bases, tap brackets Insert cord ends into ends of both springs, insert them into springs. into base slots. making sure they're . Thread holders . Install outer door, slide dishwasher into place, reconnect supplies and install mounting brackets. properly. cords through pulleys. Using pliers (since cords will be under tension), onto hinge levers. Make sure cords are not damaged during installation. For authorized servicers, additional assistance is available by contacting our Quickfinder website at http://portal.mch.bsh,q.com/portal. Copyright seated any disconnected our Technical slide cord electrical Support team at (800) 444-9091 / water or by visiting by BSH Bosch-und Siemens Hausger&te GmbH This material is intended for the sole use of BSH authorized persons and may contain unauthorized review, use, copying, disclosure, or distribution in any format is prohibited. confidential and proprietary information. Any
© Copyright 2024 ExpyDoc
