Download PDF

®
U N D E R WAT E R E L E C T R I C A L A N D F I B E R O P T I C C O N N E C T O R S
U N D E RWAT E R E L E C T R I C A L D RY- M AT E C O N N E C TO R S
RUBBER MOLDED SERIES
Table of Contents
Rubber Molded Bulkhead Connector Mates . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Right Angle and Straight Connector Indexing . . .
Typical Mated Assembly and Options . . . . . . . . . . . . . . . . .
RMA-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . .
50-A
50-1
50-2
50-3
50-4
50-5
50-6
RMA-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-MP-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-FS-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-MPD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSA-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSB-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSC-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSC-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-6
50-6
50-6
50-6
50-6
50-6
50-6
50-6
50-7
50-7
50-7
50-7
50-8
50-8
RMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSG-BCL-P-R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSG-PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSG-PBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSG-PBCLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMGS-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMGS-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-23
VMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSG-PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSG-PBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSG-PBCLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMA-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-MP-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-FS-SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-FSD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-FSD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-9
VMA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10
VSA-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10
VSA-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10
VSB-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-10
RMF-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-11
RMF-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMF-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMF-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMF-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMF-MPD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMF-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSF-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSFDE-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-11
50-11
50-11
50-11
50-11
50-11
50-12
50-12
50-12
VMF-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-13
VMF-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-FSD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-FSD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSF-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-13
50-13
50-13
50-13
50-13
50-13
50-14
50-14
RMK-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XSK-DEBCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19
RMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-19
50-26
50-26
50-26
50-26
50-26
50-26
50-26
50-27
50-27
50-27
VMK-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-28
VMK-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-FS WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-MP WOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-MPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VMK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSK-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-28
50-28
50-28
50-28
50-28
50-28
50-28
50-29
50-29
Special Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-30
Locking Sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-31
A-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSF-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VSF-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-FLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-MLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-FLS-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-FLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-FLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-MLS-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-FLS-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
K-MLS-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-15
50-15
50-15
50-15
50-15
50-15
50-16
50-16
50-17
50-18
RMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-19
50-23
50-23
50-23
50-23
50-23
50-23
50-23
50-24
50-24
50-24
50-25
50-25
RMK-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-26
LMG-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . 50-15
LMG-MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LMG-FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LMG-FSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LMG-MPD-LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LMG-MPD-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSG-BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSG-BCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSG-BC-SC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSG-BC-HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-19
50-19
50-19
50-19
50-19
50-20
50-20
50-20
50-21
50-21
50-21
50-22
50-22
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
50-32
Rubber Molded Quick Reference Mating Table . . . . . . . 50-33
(REV 0704)
RUBBER MOLDED BULKHEAD CONNECTOR MATES
VISUAL INDEX
RMA-FS R/A
RMA FS
VMA FS
Page No.
50-7
50-10
50-7
50-10
XSA-BC
VSA-BC
RMA-BCL
XSA-BCL
VMA-BCL
VSA-BCL
1/4-28
THD
5/16-24
THD
5/16-24
THD
5/16-24
THD
50-10
50-8
50-8
XSB-BCL
50-7
VSB-BCL
XSC-BC
XSC-BCL
1/4-28
THD
1/4-28
THD
3/8-24
THD
3/8-24
THD
NOTE: Torque values referenced in this literature assume installation into
dry metal threads. Please contact the a
f ctory o
f r recommendations.
VMF FS R/A
RMF FS R/A
LMG FS R/A
VMF FS
RMF FS
LMG FS
Page No.
Page No.
50-12
XSFDE-BCL
(formerly XSDE-BCL)
Page No.
50-16
50-16
LSG-BC
LSG-BCL
50-14
50-12
50-12
XSF-BC
XSF-BCL
VMF-BCL
VSF-BCL
3/8-24
THD
3/8-24
THD
1/2-20
THD
50-20
LSG-BC HP
50-17
LSG-BC SC
(formerly LSK-BC SC)
3/4-16
THD
11/16-16
THD
NOTE:
LSG-3-BC: 1/2-20
LSG-4-BC: 9/16-18
LSG-6-BC: 9/16-18
50-A (REV 0704)
NOTE:
LSG-3-BCL: 1/2-20
LSG-4-BCL: 9/16-18
LSG-6-BCL: 9/16-18
NOTE:
LSG-3-BC HP: 1/2-20
LSG-4-BC HP: 9/16-18
LSG-6-BC HP: 9/16-18
RUBBER MOLDED BULKHEAD CONNECTOR MATES
VISUAL INDEX
RMG FS R/A
RMG FS
VMG FS
50-21
Page No.
50-21
50-24
XSG-PBC
VSG-PBC
1/2-20
THD
1/2-20
THD
50-21
XSG-PBCLM
1/2-20
THD
50-25
50-25
XSG-PBCL
VSG-PBCL
1/2-20
THD
1/2-20
THD
RMG-BCL
RMGS-BC
RMGS-BCL
XSG-BCL
XSG-BCL-P-R/A
50-20
50-22
50-22
50-20
50-20
50-24
VMG-BCL
VSG-BCL
VSG-PBCLM
1/2-20
THD
3/4-16
THD
3/4-16
THD
NOTE:
RMGS-BC (1/2"NPT)
RMGS-BCL (3/4"NPT)
NOTE: Torque values referenced in this literature
assume installation into dry metal threads.
Please contact the factory o
fr
recommendations.
RMK FS R/A
RMK FS
VMK FS
Page No.
50-27
50-27
50-29
XSKDE-BCL
RMK-BCL
XSK-BCL
VMK-BCL
VSK-BCL
1-14
THD
1-14
THD
1 1/2-14
THD
50-B (REV 0704)
INTRODUCTION
Our standard rubber molded series typically consists of an in-line female neoprene connector mated to a glass
reinforced epoxy (XS) bulkhead connector. Various sizes are available ranging from single contact connectors up
through 12 contact connectors. Most are available with pins and sockets reversed to help prevent mismating of
connectors, which otherwise look identical. This also allows for socket type contacts in a connector where there is
a possibility of a "power-on" situation. Many of the bulkhead type connectors are available in 316 Stainless Steel,
and can also be manufactured of any of the exotic metals. Male in-line connectors round out the series allowing
for in-line mated sets not requiring bulkhead penetration. In addition, the WOC (without cable) type connectors
allow for field installation in the event that a connector is damaged while at sea and needs replacing, or for long
cable lengths that make cable transportation cost prohibitive.
The time proven rubber molded series is one of our most inexpensive lines and has been used on all types of
underwater instrumentation including: underwater lighting, communications, ROV's, thermistor arrays, hydrophone
arrays, and all types of sonar systems. The contacts are gold plated per ASTM-B-488 and the series is rated up to
20,000 psi in a mated condition.
PART NUMBERING SYSTEM
CONNECTORS
RM G
-
6
-
FS
-
R/A
Right Angle (optional)
Female Socket
Number of Contacts
Size
Rubber Molded
In-Line Connectors
Bulkhead Connectors
LM
Rubber Molded-Special Version
LS
Glass Reinforced Epoxy- Special Version
R/A
Right Angle
RM
Rubber Molded
RM
Metal Shell
SC
Solder Cup
VM
Reversed Rubber Molded
VM
Reversed Metal Shell
TH
Thermistor Housing
FS
Female Socket
VS
Reversed Glass Reinforced Epoxy
FSD
Female Socket Dummy
XS
Glass Reinforced Epoxy
MP
Male Plug
BC
Bulkhead Connector
MPD
Male Plug Dummy
BCL
BC w/Locking Thread
FI
Field Installable
C
COAX
HP
High Pressure
DE
Double Ended
LP
Low Pressure
HP
High Pressure
SL
Slip-on Series
IDC
Inboard Disconnect
WOC
Without Cable
P
Pigtails
50-1 (REV 0704)
GENERAL INFORMATION
RUBBER MOLDED AND ASSOCIATED SERIES
APPLICATIONS:
Standard, Reversed Rubber Molded Series
Applications requiring light to medium ruggedness
Hazardous environments
Field installable applications
Glass Reinforced Epoxy Series
Applications requiring medium ruggedness
Hazardous environments
Power transmission
Signal telemetry
Metal Shell Series
Applications requiring heavy ruggedness
Hazardous, rugged environments
Power transmission
Signal telemetry
CABLE:
Rubber Molded Series
Connector's power capability may be limited by amperage and voltage rating of cable to which it is
molded to. With the exception of field installable connectors, the in-line series are provided on a standard 18" length of 18 AWG SO cable unless otherwise specified.
Glass Reinforced Epoxy Series & Metal Shell Series
Connector's power capability may be limited by amperage and voltage rating of pigtails.
Customer must specify if pigtails are to be applied.
NOTE: Torque values referenced in this literature assume installation into
dry metal threads. Please contact the factory for recommendations.
50-2 (REV 0704)
MAINTENANCE PROCEDURES
CONNECTORS
MAINTENANCE
The following procedures detail the maintenance requirements for the Rubber Molded Series and their
associated parts. Even though this procedure appears simple, only qualified technicians should perform the maintenance. If connectors are periodically unmated SEA CON® recommends the following:
1.
Before unmating ensure connectors are free of foreign contaminates. Visually check for and
note any damage or abnormalities.
2.
After unmating visually check for and note any damage, cuts or abnormalities.
3.
Clean any grease, moisture or foreign particles from connectors and sealing surface area.
4.
In the event the internal contact surfaces are dirty or have been exposed to water, the connector should be flushed with distilled or deionized water and thoroughly dried.
5.
The surface should be dried using a low pressure (15 - 25 psi) gas stream of dry nitrogen or
filtered compressed air (dry nitrogen is preferred). This drying procedure ensures the removal of
any small foreign particles.
6.
Electrically test the connector in accordance with the parameters of the system.
7.
Apply a thin film of an appropriate silicone grease or spray to the sealing surface. Cover/protect
connector from foreign contaminates until ready to mate.
INSTALLATION & TORQUE OPERATIONS
1.
Only qualified technicians should perform installation and torquing operations.
2.
*Torque values specified apply only when connector is installed in a metal housing.
3.
Torque values listed are maximum values not to be exceeded.
4.
Locking sleeves are finger/hand tightened only.
*Torque values are noted with actual part and can be found in pages to follow.
NOTE: Torque values referenced in this literature assume installation into
dry metal threads. Please contact the factory for recommendations.
50-3 (REV 0704)
RUBBER MOLDED SERIES
TYPICAL RIGHT ANGLE AND STRAIGHT CONNECTOR INDEXING
Visual
Index
Optional
Locking
Sleeve
Visual
Index (3)
Cable
(Straight Entry)
Right Angle
Molded Body
(Elastomeric Material)
Cable
(Right Angle Entry To Connector)
Cable-Right
Angle Entry-In
Line With Index
In the case of right angle connectors, the cable is always perpendicular to the index, as shown
50-4 (REV 0704)
RUBBER MOLDED SERIES
CABLE
Neoprene outer jacket
supplied on our standard
cables
TYPICAL MATED ASSEMBLY AND OPTIONS
CABLE
Or solid rubber for dummy
RUBBER MOLDED
CONNECTOR
RUBBER MOLDED
CONNECTOR
OPTIONAL LOCKING SLEEVE (long)
For use with straight connectors
only. This long type of locking
sleeve helps to eliminate conductor
breakage at termination joint by
eliminating flexing at joint area.
RIGHT ANGLE CONNECTOR
ELECTRICAL CONTACTS
copper alloy, hard gold
plated per ASTM-B-488.
OPTIONAL LOCKING SLEEVE
For use with straight or right
BULKHEAD CONNECTORS
Material -Glass Reinforced Epoxy
eliminates all dissimilar metal
problems
BULKHEAD CONNECTORS
O-RING
Buna N, 70 Durometer is
standard. O-Rings supplied
with all connectors.
All O-Rings must be
lubricated with a thin film of
silicon or DC grease.
If IDC’s are intended for use
specify pins on low pressure
side when ordering bulkhead
connectors. Solder pots are
standard.
INBOARD DISCONNECT (IDC)
Not Water Tight (Optional)
OPTIONAL WATER. TIGHT MOLD
Polyurethane usually used;
neoprene optional (molded)
To specify pigtails add.P after
connector callout.
INBOARD NUT & WASHER
SET (SST)
(Optional)
OPTIONAL INDIVIDUAL PIGTAILS
Teflon, 18" Long.
Longer lengths available
NOTE: Torque values referenced in this literature assume installation into dry metal threads. Please contact the factory for
recommendations.
MATING
To ensure that the connectors are not damaged during mating/unmating, it is important to practice proper connect and disconnect procedures.
INCORRECT
CORRECT
50-5 (REV 0704)
RMA-FS AND ASSOCIATED PARTS
STANDARD RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM B488
Cable: 1 N 2
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
2.50
2.00
1.50
RMA-FS
.87
1.06
1.81
RMA-MP
RMA-1-FS
RMA-1-MP
1#16
RMA-FS R/A
SLIP-ON SERIES
Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 inch
Material: Special Neoprene, molded
Contacts: Brass, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 PSI
SOLDER
CUP
PIN
1.06
SOLDER
CUP
SOCKET
VISUAL
INDEX
1.53
1.85
2.32
RMA-MP-SL
RMA-FS-SL
(Uses Locking Sleeve: A-MLS-D)
(Uses Locking Sleeve: A-FLS-D)
LOCKING SLEEVES
DUMMY CONNECTORS
A-MLS-D (AVAILABLE FOR RMA-MP)
A-FLS-D (AVAILABLE FOR RMA-FS, RMA-FS-R/A)
RMA-FSD MATES TO RMA-MP
RMA-MPD-LP/HP TO RMA-FS & RMA-FS-R/A
Material: Special Neoprene, molded
Pressure Rating, Mated:
RMA-FSD (20,000PSI)
RMA-MPD-LP (<4,000 PSI)
RMA-MPD-HP (4,000 – 20,000 PSI) Male Contact Required
50-6 (REV 0704)
RMA-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL)
Dummy Connector: RMF FSD
Part Name: RMA-BCL
Material: 316 Stainless St., Internal Insulation-Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
RMA-BCL; Special insulating neoprene is compression
molded to the metal body forming a reliable seal. The
metal body can be made of stainless steel, aluminum or
other metals.
This Connector utilizes a facial o-ring seal to the
bulkhead.
O-RING (2-012)
5/16-24 UNF-2A
Mounting Torque
15 INCH LBS.
.63
1.25
.63
RMA-BCL
1#16
600VDC
Part Name: XSA-BC
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
XSA-BC
XSA-BC; The smallest standard
connector in our non-metallic series, features an
o-ring in the thread relief area. Available in single contact.
O-RING (2-009)
1/4-28 UNF
Mounting Torque
6 INCH LBS.
.370
.360
32
.052
.050
.40
.45
.18
.015R
.005
.015 R
.005
.370
.360
32
32
.052
.050
32
.37
1.8
XSA-BC
1#16
600VDC
1/4-28 UNF-2B THREAD
MOUNTING REQUIREMENT
FOR XSA BC
5/16-24 UNF
Mounting Torque
8 INCH LBS.
O-RING (2-012)
XSA-BCL
XSA-BCL; These are miniature, single contact connectors which feature a locking sleeve provision. The o-ring is
located on a step under the hex and seals by flush
mounting to the bulkhead. Same Material and Pressure
as XSA-BC.
.12
.31
.62
.18
.62
2.00
XSA-BCL
1#16
1/4-28 UNF
Mounting Torque
6 INCH LBS.
O-RING (2-012)
600VDC
.62
.12
.31
.62
.18
XSB-BCL
1#16
2.00
600VDC
XSB-BCL
XSB-BCL; A miniature connector body very similar to the
XSA BCL, but utilizes a smaller installation thread. The
small thread size requires care in installation to avoid
damaging or cracking. The o-ring is located on a stop
under the hex and seals by flush mounting to the bulkhead. Same Material and Pressure as XSA-BC.
NOTE: Torque values referenced in this literature assume
installation into dry metal threads. Please contact the
factory for recommendations.
50-7 (REV 0704)
RMA-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL)
Dummy connector RMA FSD
Part Names: XSC-BC, XSC-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 10,000 psi
XSC-BC, XSC-BCL; These connectors feature a radial type
o-ring seal, good for up to 10,000 PSI, mated. Available only in
single contact.
O-RING (2-011)
3/8-24 UNF
Mounting Torque
12 INCH LBS.
.288
.50
.50
.18
.56
XSC-BC
1#16
2.0
600VDC
XSC-BC
.439
.437
32
.005 R
.020 R
.289
.287
3/8-24 UNF-2B THREAD
MOUNTING REQUIREMENT
3/8-24 UNF
Mounting Torque
12 INCH LBS.
.37
O-RING (2-011)
.288
.18
.18
.56
.68
XSC-BCL
1#16
2.09
600VDC
XSC-BCL
NOTE: Torque values referenced in this literature assume installation into dry
metal threads. Please contact the factory for recommendations.
50-8 (REV 0704)
VMA-FS AND ASSOCIATED PARTS
REVERSED RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Cable: 1 N 2
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
2.50
2.00
1.50
.87
VMA-FS
1.06
1.81
VMA-1-FS
VMA-1-MP
1#16
VMA-MP
VMA-FS R/A
SLIP-ON SERIES
Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 INCH
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage
requirements Pressure Rating, Mated: up to 20,000 psi
SOLDER
CUP
PIN
SOCKET
SOLDER
CUP
BOOT
BOOT
1.53
1.06
1.81
VMA-FS-SL
VMA-MP SL
(Uses Locking Sleeve: A-FLS-D)
(Uses Locking Sleeve: A-MLS-D)
LOCKING SLEEVES
A-MLS-D (AVAILABLE FOR VMA-MP)
A-FLS-D (AVAILABLE FOR VMA-FS, VMA-FS-R/A)
DUMMY CONNECTORS
VMA-FSD-LP MATES TO VMA-MP
VMA-FSD-HP MATES TO VMA-MP
VMA-MPD MATES TO VMA-FS & VMA-FS-R/A
Material: Special Neoprene, Molded
Pressure Rating, Mated:
VMA-FSD-LP < 4,000 PSI (CONNECTOR BODY W/O MALE PIN)
VMA-FSD-HP 4,000 - 20,000PSI
VMA-MPD 20,000 PSI
50-9 (REV 0704)
VMA-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO VMA-FS & VMA-FS-R/A & VMA-FS SL)
Dummy Connector: VMA-FS D HP or VMA FS D LP
Part Name: VMA-BCL
Material: 316 Stainless St., Internal Insulation-Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
O-RING (2-012)
5/16-24 UNF-2A
Mounting Torque
8 INCH LBS.
VMA-BCL; Special insulating neoprene is
compression molded to the metal body forming a
reliable seal. The metal body can be made of stainless
steel, aluminum or other metals.
This connector utilizes a facial o-ring to seal to the
bulkhead.
.63
1.25
.63
VMA-BCL
1#16
600VDC
Part Names: VSA-BC, VSA-BCL, VSB-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
VSA-BC
VSA-BC; The smallest standard connector in our nonmetallic series, features an
o-ring in the thread relief area. Available in single
contact.
O-RING (2-010)
5/16-24 UNF
Mounting Torque:
5 INCH LBS.
RECESSED SOCKET
.420
.410
32
.052
.050
.62
.50
.18
.015R
.005
.015 R
.005
.420
.410
32
32
.052
.050
32
.44
1.7
VSA-BC
1#16
O-RING (2-012)
5/16-24 UNF
Mounting Torque:
8 INCH LBS.
RECESSED SOCKET
5/16-24 UNF-2B THREAD
MOUNTING REQUIREMENT
FOR VSA BC
.12
.38
.62
.18
.62
1.7
VSA-BCL
1#16
1/4-28 UNF
Mounting Torque:
4 INCH LBS.
O-RING (2-012)
VSB-BCL
VSB-BCL; This is a miniature connector body very
similar to the VSA-BCL, but utilizes a smaller installation
thread. The small thread size requires care in installation to avoid damaging or cracking. The o-ring is
located on a stop under the hex and seals by flush
mounting to the bulkhead.
RECESSED SOCKET
.12
.38
VSA-BCL
VSA-BCL; Miniature single contact connectors which
feature a locking sleeve provision. The o-ring is located
on a step under the hex and seals by flush mounting to
the bulkhead.
.62
.18
1.7
Note:
.62
VSB-BCL
1#16
50-10 (REV 0704)
Torque values referenced in this literature assume
installation into dry metal threads. Plese contact
the factory for recommendations.
RMF-FS AND ASSOCIATED PARTS
STANDARD RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
See Specific Configuration for Voltage Rating
Pressure Rating, Mated: up to 10,000 psi
2.45
1.18
VISUAL
INDEX
∅.47
∅.47
1.60
RMF 1 FS
RMF 2 FS
.81
1.4
RMF 1 MP
RMF 2 MP
RMF 1 FS R/A
RMF 2 FS R/A
1
RMF-C-FS/MP
COAX
22 AWG/20 Ω
(Cable: CN4 or CN5)
RMF-1-FS/MP
1#14
(Cable: 18/1SO)
or Equivalent
600 VDC
600 VDC
RMF-2-FS/MP
2#16
(Cable: 18/2SJO)
300 VDC
LOCKING SLEEVES
DUMMY CONNECTORS
F-MLS-D (AVAILABLE FOR RMF-MP)
XSF-FLS-D (AVAILABLE FOR RMF-FS, RMF-FS-R/A)
Note: Specify number of conductors when ordering
RMF-FSD MATES TO RMF-MP
RMF-MPD-HP MATES TO RMF-FS & RMF-FS –R/A
RMF-MPD-LP MATES TO RMF-FS & RMF-FS-R/A
Material: Special Neoprene, Molded
Pressure Rating, Mated:
RMF-FSD (10,000 PSI)
RMF-MPD-HP (HIGH PRESSURE, 4,000 PSI-10,000 PSI, CONTACT REQUIRED)
RMF-MPD-LP (LOW PRESSURE, < 4,000 PSI, NO CONTACT REQUIRED)
50-11 (REV 0704)
RMF-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO RMF-FS & RMF-FS-R/A & RMF FS WOC)
Dummy Connector RMF-FSD
Part Names: XSF-BC, XSF-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per MIL-G-45204
Pressure Rating, Mated: up to 10,000 psi
XSF-BC; Features radial o-ring seal.
XSF-BCL; These connectors feature a locking sleeve provision and utilize a radial o-ring seal.
O-RING (2-011)
3/8-24 UNF
Mounting Torque
12 INCH LBS.
.50
.288
.50
.56
.439
.437
XSF-BC
.18
.020 R
2.0
.289
.287
.005 R
O-RING (2-011)
3/8-24 UNF
Mounting Torque
12 INCH LBS.
.68
.288
.31
.56
3/8-24 UNF-2B THREAD
MOUNTING REQUIREMENT
.18
.18
XSF-BCL
2.00
XSF-BC/BCL
COAX
#22 AWG/20 Ω
XSF-1-BC/BCL
1#14
XSF-2-BC/BCL
2#16
Description: A double-ended connector which accepts a
mating connector on either end. The same locking sleeve also
fits both ends. This connector utilizes a facial o-ring seal to the
bulkhead.
Part Name: XSFDE-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated
Pressure Rating, Mated: up to 10,000 psi
LOW PRESSURE
HIGH PRESSURE
O-RING (2-021)
11/16-16 UNF
Mounting Torque
20 INCH LBS.
XSF-1-BCLDE
1#14
.37
XSF-2-BCLDE
2#16
.31
1.25
.31
.87
2.81
NOTE: Torque values referenced in this literature assume
installation into dry metal threads. Please contact the
factory for recommendations.
50-12 (REV 0704)
XSFDE-BCL
(FORMERLY KNOWN AS XSDE-BCL)
VMF-FS AND ASSOCIATED PARTS
REVERSED RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: See specific configuration
Pressure Rating, Mated: up to 20,000 psi
VMF-FS
VMF-MP
VMF-FS R/A
VMF-C-FS
600 VDC
CABLE:
CN4 or CN5
VMF-1-FS
600 VDC
CABLE:
18/1SO or
EQUIVALENT
LOCKING SLEEVES
VMF-2-FS
300 VDC
CABLE:
18/2 SJO
DUMMY CONNECTORS
Note: Specify number of conductors when ordering
VSF-MLS-D (AVAILABLE FOR VMF-MP)
VSF-FLS-D (AVAILABLE FOR VMF-FS, VMF-FS-R/A)
VMF-FSD-HP MATES TO VMF-MP
VMF-FSD-LP MATES TO VMF-MP
VMF-MPD MATES TO VMF-FS & VMF-FS -R/A
MATERIAL: SPECIAL NEOPRENE, MOLDED
PRESSURE RATING, MATED:
VMF-MPD 10,000 PSI
VMF-FSD-HP (HIGH PRESSURE, 4,000-10,000 PSI CONTACT REQUIRED)
VMF-FSD-LP (LOW PRESSURE, < 4,000 PSI NO CONTACT REQUIRED)
50-13 (REV 0704)
VMF-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO VMF-FS & VMF-FS-R/A & VMF FS WOC)
Dummy Connector: VMF-FSD
Part Name: VMF-BCL
Material: 316, Stainless Steel
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
VMF-BCL; Special insulating neoprene is permanently molded to the metal shell. These types of
connectors are used where physical abuse would
be too great for the non-metallic (glass reinforced
epoxy) series.
O-RING (2-114)
A
1/2-20 UNF-2A
Mounting Torque
50 INCH LBS.
A
1.33
.93
FLATS
VMF-BCL
1
1
2
VMF-C-BCL
COAX
#22 AWG/20Ω
VMF-1-BCL
1#14
Part Name: VSF-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
1/2-20 UNF-2A
Mounting Torque
15 INCH LBS.
VMF-2-BCL
1#16
VSF-BCL; Available in coax, 1 and 2 contacts,
features a facial o-ring seal to the bulkhead.
O-RING (2-114)
1
2
.58
1.33
1
2
VSF-C-BCL
COAX
#22 AWG/20Ω
VSF-1-BCL
1#14
NOTE: Torque values referenced in this literature assume
installation into dry metal threads. Please contact the
factory for recommendations.
50-14 (REV 0704)
VSF-2-BCL
2#16
.93
FLATS
LMG-FS AND ASSOCIATED PARTS
STANDARD RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
2.69
2.15
1.12
∅.75
∅.75
LMG-FS
2.15
.50
2.00
LMG-FS R/A
LMG-MP
LMG-3-FS
1#14
2#16
(Cable: 18/3SO)
LMG-4-FS
1#14
3#16
(Cable: 18/4SO)
LOCKING SLEEVES
LMG-6-FS
1#14
5#16
(Cable: 18/6SO)
DUMMY CONNECTORS
G-MLS-D (AVAILABLE FOR LMG-MP)
G-FLS-D (AVAILABLE FOR LMG-FS, LMG-FS-R/A)
Note: Specify number of conductors when ordering
LMG-FSD MATES TO LMG-MP
LMG-MPD LP/HP MATES TO LMG-FS & LMG-FS-R/A
MATERIAL: SPECIAL NEOPRENE, MOLDED
PRESSURE RATING, MATED:
LMG-FSD (20,000 PSI)
LMG-MPD-HP (HIGH PRESSURE, 4,000 PSI-20,000 PSI, CONTACT REQUIRED)
LMG-MPD-LP (LOW PRESSURE, < 4,000 PSI NO CONTACT REQUIRED)
50-15 (REV 0704)
LMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
Part Name: LSG-BC, LSG-BCL
Mates to LMG-FS, LMG-FS R/A
Dummy Connector - LMG-FS D
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 3,000 psi
1/2-20 UNF
Mounting Torque
15 INCH LBS.
LSG-BC, LSG-BCL; These non-metallic connectors utilize a facial o-ring seal to the bulkhead. The
LSG-BCL has a locking sleeve provision.
1/2-20 UNF
Mounting Torque
15 INCH LBS.
O-RING (2-017)
∅.93
O-RING (2-017)
∅.93
.18
.18
.18
.68
HEX
.50
1.40
.93
HEX
.33
.50
1 #14
2 #16
1 #14
2 #16
1.50
LSG-3-BC
LSG-3-BCL
Note: Does not mate to RMG- FS or RMG-FS R/A
9/16-18 UNF
Mounting Torque
18 INCH LBS.
9/16-18 UNF
Mounting Torque
18 INCH LBS.
O-RING (2-017)
O-RING (2-017)
∅.93
∅.93
.18
.18
.18
.68
HEX
.50
1.40
.93
HEX
.50
.33
1 #14
3 #16
1 #14
3 #16
1.50
LSG-4-BC
LSG-4-BCL
Note: Does not mate to RMG- FS or RMG-FS R/A
9/16-18 UNF
Mounting Torque
18 INCH LBS.
9/16-18 UNF
Mounting Torque
18 INCH LBS.
O-RING (2-017)
∅.93
O-RING (2-017)
∅.93
.25
.18
.18
.68
HEX
.50
1.56
.50
1 #14
5 #16
.93
HEX
.33
1 #14
5 #16
1.58
LSG-6-BC
LSG-6-BCL
Note: Also mates to RMG-FS and RMG-FS R/A
NOTE: Torque values referenced in this literature assume installation into dry metal threads.
Please contact the factory for recommendations.
50-16 (REV 0704)
LMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
Part Name: LSG-BC-SC (Formerly known as LSK-BC-SC)
Mates to LMG-FS, LMG-FS R/A
Dummy Connector: LMG-FSD
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 5,000 psi
3/4-16 UNF
Mounting Torque
70 INCH LBS.
LSG-BC-SC; These non-metallic connectors utilize a
radial o-ring seal to the bulkhead.
O-RING (2-016)
∅1.06
.35
.87
HEX
.18
.97
.43
1.93
LSG-3-BC-SC
Note: Does not mate to RMG-FS or RMG-FS R/A.
32
3/4-16 UNF
Mounting Torque
70 INCH LBS.
.752
.750
.020 R
.351
.349
.005 R
O-RING (2-016)
∅1.06
3/4-16 UNF-2B THREAD
MOUNTING REQUIREMENT
LSG BC SC
.35
.87
HEX
.18
.43
.97
1.93
LSG-4-BC-SC
Note: Does not mate to RMG-FS or RMG-FS R/A.
3/4-16 UNF
Mounting Torque
70 INCH LBS.
LSG-3-BC-SC
1#14
2#16
O-RING (2-016)
∅1.06
.35
.87
HEX
.18
.97
.43
2.03
LSG-6-BC-SC
Note: Also mates to RMG-FS and RMG-FS R/A.
NOTE: Torque values referenced in this literature assume installation into dry metal threads.
Please contact the factory for recommendations.
50-17 (REV 0704)
LSG-4-BC-SC
1#14
3#16
LSG-6-BC-SC
1#14
5#16
LMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO LMG FS & LMG-FS-R/A)
Dummy Connector: LMG-FSD
Part Name: LSG-BC-HP
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 10,000 psi
1/2-20 UNF
Mounting Torque
15 INCH LBS.
LSG-BC-HP; These non-metallic connectors feature a
facial o-ring seal to the bulkhead.
O-RING (2-017)
∅.93
.18
.68
HEX
.50
.43
1 #14
2 #16
1.64
LSG-3-BC-HP
Note: Does not mate to RMG-FS or RMG-FS R/A
9/16-18 UNF
Mounting Torque
18 INCH LBS.
O-RING (2-017)
∅.93
.18
.68
HEX
.50
.43
1 #14
3 #16
1.64
LSG-4-BC-HP
Note: Does not mate to RMG-FS or RMG-FS R/A
9/16-18 UNF
Mounting Torque
18 INCH LBS.
O-RING (2-017)
∅.93
.18
.68
HEX
.50
.43
1 #14
5 #16
1.74
LSG-6-BC-HP
Note: Also mates to RMG-FS and RMG-FS R/A
NOTE: Torque values referenced in this literature assume installation into dry
metal threads. Please contact the factory for recommendations.
50-18 (REV 0704)
RMG-FS AND ASSOCIATED PARTS
STANDARD RUBBER MOLDED
IN-LINE SERIES
Note: Available with grippers, must specify.
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
2.9
2.13
1.13
∅.75
∅.75
2.06
RMG FS
2.6
RMG FS R/A
RMG-MP
1
1
1
3
RMG-1-FS
1#10
(Cable: 18/1SO)
or Equivalent
RMG-2-FS
1#10
1#14
(Cable: 18/2SO)
1
4
2
2
RMG-3-FS
1#10
2#14
(Cable: 18/3SO)
1
5
4
2
3
3
5
2
RMG-5-FS
1#14
4#16
(Cable: 18/5SO)
RMG-4-FS
1#14
3#16
(Cable: 18/4SO)
4
1
2
6 3
RMG-6-FS
1#14
5#16
(Cable: 18/6SO)
WOC CONNECTORS
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene
jacketed cables, Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
Part Name: RMG-FS WOC, RMG-MP WOC
Material: Special Neoprene, Molded
Contacts: Brass, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements Pressure
Rating, Mated: up to 20,000 psi
RMG-1-FS
MP-WOC
1 #10 AWG
1
3 2
RMG-3-FS
MP-WOC
1 #10 AWG
2 #14 AWG
LOCKING SLEEVES
RMG-2-FS
MP-WOC
1 #10 AWG
1 #14 AWG
1
4
2
3
RMG-4-FS
MP-WOC
1 #14 AWG
3 #16 AWG
DUMMY CONNECTORS
Note: Must specify cable OD when using G-FLS-X
Note: specify number of conductors when ordering
G-MLS-D (AVAILABLE FOR RMG-MP, RMG-MP WOC)
G-FLS-D (AVAILABLE FOR RMG-FS, RMG-FS-R/A,
RMG-FS WOC)
G-MLS-S (AVAILABLE FOR RMG-MP, RMG-MP WOC )
G-FLS-S (AVAILABLE FOR RMG-FS, RMG-FS-R/A,
RMG-FS WOC)
G-FLS-X (AVAILABLE FOR RMG-FS) Must specify cable O.D.
when ordering G-FLS-X
RMG-FSD MATES TO RMG-MP, BCL & XSG-BCL,
XSG-PBC, XSG-PBCL & XSG-PBCLM
RMG-MPD MATES TO RMG-FS & RMG FS-R/A
MATERIAL: SPECIAL NEOPRENE, MOLDED
PRESSURE RATING, MATED:
RMG-FSD (20,000 PSI)
RMG-MPD-LP (LOW PRESSURE < 4,000 PSI)
RMG-MPD-HP (4,000 PSI-20,000 PSI) Contact Required
50-19 (REV 0704)
RMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO RMG FS & RMG-FS-R/A & RMG FS WOC)
Dummy Connector RMG FS D
Part Name: RMG-BCL
Material: 316 Stainless St., Internal Insulation-Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-448
Pressure Rating, Mated: up to 20,000 psi
RMG-BCL; Special Insulating neoprene is permanently molded
to the metal shell. These types of connectors are used where
physical abuse would be too great for the non-metallic (glass
reinforced epoxy) series. The RMG BCL has a locking sleeve
provision and utilizes a facial O-ring seal to the bulkhead.
3/4-16 UNF
Mounting Torque
85 INCH LBS.
Part Name: XSG-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-448
Pressure Rating, Mated: up to 20,000 psi
XSG-BCL; One of our oldest connectors in the non-metallic
series, with male pin as shown. Connector is one homogeneously molded unit. Available with different thread lengths
as indicated. TheXSG BCL has a locking sleeve provision
and utilizes a facial O-ring seal to the bulkhead.
3/4-16 UNF
Mounting Torque
85 INCH LBS.
O-RING (2-213)
O-RING (2-213)
1 3/8
HEX
1.18
.87
1.18
.50
RMG-BCL
XSG-BCL
3/4-16 UNF
Mounting Torque
85 INCH LBS.
O-RING (2-213)
INDEX
1
1
2
RMG-2-BCL
XSG-2-BCL
1 #10
1 #14
RMG-1-BCL
XSG-1-BCL
1 #10
1
2
3
1
2
4
3
RMG-3-BCL
XSG-3-BCL
1 #10
2 #14
1
2
RMG-4-BCL
XSG-4-BCL
1 #14
3 #14
3
2
4
RMG-5-BCL
XSG-5-BCL
1 #14
4 #16
3
1
5
6
4
RMG-6-BCL
XSG-6-BCL
1 #14
5 #16
Part Name: XSG-BCL-P-R/A
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-448
Pigtails; teflon insulated #18 AWG
Pressure Rating, Mated: up to 20,000 psi
.87
1.18
XSG-BCL LT
XSG-BCL-P-R/A; A non-metallic low profile right
angle bulkhead connector featuring a locking sleeve
provision and utilizing a facial o-ring seal to the
bulkhead.
1.00
NOTE: Torque values referenced in this literature assume
installation into dry metal threads. Please contact
the factory for recommendations.
1.25
1
2
.87
1
2
3
3
O-RING (2-017)
XSG-2-BCL-P-R/A
1 #10
1 #14
1/2-20 UNF
Mounting Torque
15 INCH LBS
18.0
XSG-BCL-P-R/A
50-20 (REV 0704)
1
2
XSG-3-BCL-P-R/A
1 #10
2 #14
4
XSG-4-BCL-P-R/A
1 #14
3 #16
RMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO RMG FS & RMG-FS-R/A & RMG-FS WOC)
Dummy Connector: RMG-FSD
XSG-PBC; Small footprint non-metallic connector
utilizing an o-ring in the thread relief area to seal to
the bulkhead.
Part Name:: XSG-PBC, XSG-PBCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pigtails: teflon insulated #18 AWG
Pressure Rating, Mated: up to 5,000 psi
O-RING (2-012)
1/2-20 UNF
Mounting Torque
15 INCH LBS.
.62
.38
XSG-PBC
.55
1.55
18.00
.504
.502
.020 R
1
1
1
2
2
XSG-1-PBC
1 #10
3
1
2
4
3
XSG-2-PBC
1 #10
1 #14
XSG-3-PBC
1 #10
2 #14
1/2-20 UNF
Mounting Torque
15 INCH LBS.
O-RING (2-012)
.083
.081
XSG-4-PBC
1 #14
3 #16
1/2-20 UNF-2B THREAD
MOUNTING REQUIREMENT
.81
.62
XSG-PBCL; Small footprint non-metallic connector utilizing an o-ring in the thread relief area to seal
to the bulkhead. Features a locking sleeve
provision.
.62
18.00
2.06
∅.94
XSG-PBCL
1
1
1
2
2
XSG-1-PBCL
1 #10
3
1
2
3
XSG-2-PBCL
1 #10
1 #14
XSG-3-PBCL
1 #10
2 #14
4
XSG-4-PBCL
1 #14
3 #16
Part Name: XSG-PBCLM
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pigtails: teflon insulated #18 AWG
Pressure Rating, Mated: up to 5,000 psi
XSG-PBCLM; Non-metallic connector utilizing a
facial o-ring seal to the bulkhead. Features a
locking sleeve provision.
O-RING (2-017)
1/2-20 UNF
Mounting Torque
15 INCH LBS.
1
.94
2
XSG-1-PBCLM
1 #10
.46
XSG-PBCLM
.50
18.00
1
1.59
NOTE: Torque values referenced in this literature assume installation into dry metal
threads. Please contact the factory for recommendations.
50-21 (REV 0704)
XSG-2-PBCLM
1 #10
1 #14
1
2
3
1
2
3
XSG-3-PBCLM
1 #10
2 #14
4
XSG-4-PBCLM
1 #14
3 #16
RMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO RMG FS & RMG-FS-R/A & RMG-FS WOC)
Dummy Connector: RMG-FSD
Part Names: RMGS-BC, RMGS-BCL
Material: 316 Stainless Steel
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 5,000 psi
RMGS-BC; Features a stainless steel body,
insulating neoprene, and pipe thread for sealing to
bulkhead. No O-Ring required for sealing.
1/2 -14 NPT
.87
HEX FLATS
.62
.75
RMGS-BC
1.32
RMGS-BCL; Features a stainless steel body,
insulating neoprene, and pipe thread for sealing to
bulkhead. No O-Ring required for sealing. Features
a locking sleeve provision.
3/4 -14 NPT
1.06
HEX FLATS
.62
.75
RMGS-BCL
1.21
1
1
2
RMGS-1-BC/BCL
1 #10 AWG
2
RMGS-2-BC/BCL
1 #10 AWG
1 #14 AWG
3
RMGS-3-BC/BCL
1 #10 AWG
2 #14 AWG
NOTE: Torque values referenced in this literature assume installation into dry metal
threads. Please contact the factory for recommendations.
50-22 (REV 0704)
1
2
4
3
RMGS-4-BC/BCL
1 #14 AWG
3 #16 AWG
VMG-FS AND ASSOCIATED PARTS
REVERSED RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-448
Voltage Rating: 600 VDC-contact factory for higher voltage
requirements
Pressure Rating, Mated: up to 20,000 psi
2.9
2.13
VISUAL INDEX
(IN-LINE WITH CONTACT #1)
1.13
∅.75
∅.75
2.6
2.06
VMG-MP
VMG-FS
VMG-FS R/A
VMG-1-FS
1 #14
(Cable: 18/1SO)
or Equivalent
VMG-2-FS
1 #14
1 #16
(Cable: 18/2SO)
VMG-3-FS
1 #14
2 #16
(Cable: 18/3SO)
VMG-4-FS
1 #14
3 #16
(Cable: 18/4SO)
WOC CONNECTORS
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene
jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
Part Names: VMG-FS WOC, VMG-MP WOC
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-448
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
INDEX
INDEX
∅.75
∅.56
∅.75
.50
∅.56
1.12
2.37
3.00
VMG-1-FS-WOC
1 #14
LOCKING SLEEVES
VMG-2-FS-WOC
1 #14
1 #16
G-MLS-D (AVAILABLE FOR VMG-MP (VMG-MP-WOC))
G-FLS-D (AVAILABLE FOR VMG-FS, VMG-FS-R/A, VMG-FS WOC
G-FLS-X (AVAILABLE FOR VMG-FS) Must specify cable O.D.
Note: Must specify cable OD when using G-FLS-X
VMG-3-FS-WOC
1 #14
2 #16
VMG-4-FS-WOC
1 #14
3 #16
DUMMY CONNECTORS
Note: specify number of conductors when ordering
VMG-FSD MATES TO VMG-MP
VMG-MPD MATES TO VMG-FS & VMG-FS-R/A & VMG-FS WOC
MATERIAL: SPECIAL NEOPRENE, MOLDED
PRESSURE RATING, MATED:
VMG-FSD-LP (LOW PRESSURE < 4,000PSI, NO CONTACT REQUIRED)
VMG-FSD-HP (4,000-20,000 PSI, CONTACT IS REQUIRED)
VMG-MPD (20,000 PSI)
50-23 (REV 0704)
VMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO VMG-FS, VMG-FS-R/A & VMG-FS WOC)
Dummy Connector VMG-FS D
Part Name: VMG-BCL
Material: 316 Stainless St., Internal Insulation-Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
Part Name: VSG-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
VMG-BCL; Special insulating neoprene is permanently molded
to the metal shell. These types of connectors are used where
physical abuse would be too great for the non-metallic (glass
reinforced epoxy) series. The VMG BCL features a locking sleeve
provision and utilizes a facial o-ring seal to the bulkhead.
VSG-BCL; One of our oldest connectors in the non-metallic
series, with female sockets as shown. Connector is one homogeneously molded unit. Available with different thread lengths
as indicated. The VSG BCL features a locking sleeve provision
and utilizes a facial o-ring seal to the bulkhead.
O-RING (2-213)
3/4-16 UNF
O-RING (2-213)
3/4-16 UNF
1 3/8
HEX
1.18
.50
.87
1.18
VSG-BCL
VMG-BCL
O-RING (2-213)
3/4-16 UNF
1
1
1
2
2
1
2
3
VMG-2-BCL
VSG-2-BCL
1 #14
1 #16
VMG-1-BCL
VSG-1-BCL
1 #14
3
VMG-3-BCL
VSG-3-BCL
1 #14
2 #16
4
VMG-4-BCL
VSG-4-BCL
1 #14
3 #16
.87
Part Name: VSG-PBC
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pigtails: teflon insulated #18 AWG
Pressure Rating, Mated: up to 5,000 psi
1.18
VSG-BCL LT
VSG-PBC; Non-Metallic connector utilizing an o-ring in the
thread relief area to seal the bulkhead.
O-RING (2-012)
1/2-20 UNF
Mounting Torque
15 INCH LBS.
.38
.62
.55
18.00
VSG-PBC
1.55
.504
.502
32
1
1
2
VSG-1-PBC
1 #14
VSG-2-PBC
1 #14
1 #16
1
2
3
1
2
3
VSG-3-PBC
1 #14
2 #16
.020 R
4
VSG-4-PBC
1 #14
3 #16
NOTE: Torque values referenced in this literature assume installation into dry metal
threads. Please contact the factory for recommendations.
50-24 (REV 0704)
1/2-20 UNF-2B THREAD
MOUNTING REQUIREMENT
.083
.081
VMG-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS & MOUNTING REQUIREMENT
(MATES TO VMG FS & VMG-FS-R/A)
Part Name: VSG-PBCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pigtails: Teflon insulated #18 AWG
Pressure Rating, Mated: up to 5,000 psi
VSG-PBCL; Non-metallic connector that features
a locking sleeve provision and utilizes an o-ring in
the thread relief area to seal to the bulkhead.
O-RING (2-012)
1/2-20 UNF
Mounting Torque
15 INCH LBS.
RECESSED
SOCKETS
.62
.62
.81
∅.94
18.00
1.55
.504
.502
VSG-PBCL
.020 R
1
1
2
VSG-1-PBCL
1 #14
VSG-2-PBCL
1 #14
1 #16
1
2
1
2
3
4
3
VSG-3-PBCL
1 #14
2 #16
.083
.081
1/2-20 UNF-2B THREAD
MOUNTING REQUIREMENT
VSG-4-PBCL
1 #14
3 #16
Part Name: VSG-PBCLM
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pigtails: Teflon insulated #18 AWG
Pressure Rating, Mated: up to 5,000 psi
VSG-PBCLM; Non-Metallic connector featuring a
locking sleeve provision. VSG-PBCLM utilizes a
facial o-ring seal to the bulkhead.
O-RING (2-017)
1/2-20 UNF
Mounting Torque
15 INCH LBS.
RECESSED
SOCKETS
.50
.46
.94
18.00
1.59
VSG-PBCLM
1
1
2
VSG-1-PBCLM
1 #14
VSG-2-PBCLM
1 #14
1 #16
1
2
3
1
2
3
VSG-3-PBCLM
1 #14
2 #16
NOTE: Torque values referenced in this literature assume installation into dry
metal threads. Please contact the factory for recommendations.
50-25 (REV 0704)
4
VSG-4-PBCLM
1 #14
3 #16
RMK-FS AND ASSOCIATED PARTS
STANDARD RUBBER MOLDED
IN-LINE SERIES
Note: Available with grippers, must specify.
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
3.13
2.75
VISUAL
INDEX
VISUAL INDEX
(IN-LINE WITH CONTACT #1)
1.63
∅1.06
∅1.06
SEALING
SURFACE
2.6
RMK-FS
2.31
RMK-MP
RMK-FS R/A
1
1
1
1
1
1
1
3
RMK-1/0-FS
RMK-1-FS
1 #1/0
1 #8 AWG
(Cable: 1/0 Welding) (Cable: 8/1SO)
RMK-6/8-FS
1 #6 AWG
1 #8 AWG
(Cable: 8/2SO)
4
3
3
3
4
3
2
12
9
7
3
3
5
5
1
8
2
9
7
6
4
2
1
8
2
8
2
2
2
2
3
2
7
2
1
7
6
6
5
4
6
6
5
4
5
4
11
5
10
4
RMK-8-FS
RMK-2-FS
RMK-3-FS
RMK-4-FS
RMK-5-FS
RMK-6-FS
RMK-7-FS
RMK-9-FS
RMK-12-FS
1 #14 AWG
1 #10 AWG
1 #10 AWG
1 #10 AWG
1 #10 AWG
1 #14 AWG
1 #14 AWG
1 #14 AWG
1 #14 AWG
7 #16 AWG
1 #14 AWG
2 #14 AWG
3 #14 AWG
4 #14 AWG
5 #16 AWG
6 #16 AWG
8 #16 AWG
11 #16 AWG
(Cable: 18/2SO) (Cable: 18/3SO) (Cable: 18/4SO) (Cable: 18/5SO) (Cable: 18/6SO) (Cable: 18/7SO) (Cable: 18/8SO) (Cable: 18/10SO) (Cable: 18/12SO)
WOC CONNECTORS
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene
jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
Inexpensive plastic syringes can be used as molds.
Part Names: RMK-FS WOC, RMK-MP WOC
Material: Special Neoprene, Molded
Contacts: Brass, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
1
1
1
1
2
2
3
RMK-1-FS
1 #8 AWG
RMK-6/8-FS
1 #6 AWG
1 #8 AWG
RMK-2-FS
1 #10 AWG
1 #14 AWG
1
1
7
2
5
RMK-3-FS
1 #10 AWG
2 #14 AWG
RMK-4-FS
1 #10 AWG
3 #14 AWG
6
2
6
2
7
4
3
RMK-5-FS
1 #10 AWG
4 #14 AWG
3
5
4
RMK-6-FS
1 #14 AWG
5 #16 AWG
LOCKING SLEEVES
3
5
4
RMK-7-FS
1 #14 AWG
6 #16 AWG
2
7
RMK-8-FS
1 #14 AWG
7 #16 AWG
8
12
9
2
11 10
5
4
9
3
6
5
4
1
1
8
2
8
6
3
2
3
RMK-1/0-FS
1 #1/0
1
1
2
4
5
4
RMK-9-FS
1 #14 AWG
8 #16 AWG
3
7
6
RMK-12-FS
1 #14 AWG
11 #16 AWG
DUMMY CONNECTORS
K-MLS-D (AVAILABLE FOR RMK-MP & RMK-MP WOC)
K-FLS-D (AVAILABLE FOR RMK-FS, RMK-FS-R/A, RMK-FS WOC)
K-MLS-S (AVAILABLE FOR RMK-MP, RMK-MP WOC)
K-FLS-S (AVAILABLE FOR RMK-FS, RMK-FS R/A & RMK-FS WOC)
K-FLS-X (AVAILABLE FOR RMK-FS)
(Must specify cable O.D. when ordering K-FLS-X)
Note: specify number of conductors when ordering
RMK-FSD MATES TO RMK-MP
RMK-MPD MATES TO RMK-FS & RMK-FS-R/A
Material: Special Neoprene, Molded
Pressure Rating, Mated:
RMK-FSD (20,000 PSI)
RMK-MPD-LP (LOW PRESSURE < 4,000 PSI, NO CONTACT REQUIRED)
RMK-MPD-HP (4,000-20,000 PSI CONTACT IS REQUIRED)
50-26 (REV 0704)
RMK-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO RMK-FS & RMK-FS-R/A & RMK-FS WOC)
Dummy Connector: RMK-FSD
NOTE: Torque values referenced in this literature assume
installation into dry metal threads. Please contact the
factory for recommendations.
Part Name: RMK-BCL
Material: 316 Stainless St.; Internal Insulation: Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure rating, Mated: up to 20,000 psi
Part Name: XSK-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
RMK-BCL; Special Insulating neoprene is permanently molded
to the metal shell. These types of connectors are used where
physical abuse would be too great for the non-metallic (glass
reinforced epoxy) series. The RMK BCL has a locking sleeve
provision and utilizes a facial O-ring seal to the bulkhead.
XSK-BCL; One of our oldest connectors in the non-metallic
series, with male pin as shown. Connector is one homogeneously
molded unit. Available with different thread lengths as indicated.
TheXSK BCL has a locking sleeve provision and utilizes a facial
O-ring seal to the bulkhead.
VISUAL INDEX
(IN-LINE WITH CONTACT #1)
VISUAL INDEX
(IN-LINE WITH CONTACT #1)
Mounting Torque
130 inch lbs.
Mounting Torque
130 inch lbs.
.87
1-14 UNS
.87
RMK-BCL
XSK-BCL
1-14 UNS
VISUAL INDEX
(IN-LINE WITH CONTACT #1)
Mounting Torque
130 inch lbs.
1.25
VISUAL
INDEX
XSK-BCL LT
1-14 UNS
6
XSK-1/0-BCL
1 #1/0
RMK-1-BCL
XSK-1-BCL
1 #8 AWG
RMK-6/8-BCL
XSK-6/8-BCL
1 #6 AWG
1 #8 AWG
RMK-2-BCL
XSK-2-BCL
1 #10 AWG
1 #14 AWG
RMK-3-BCL
XSK-3-BCL
1 #10 AWG
2 #14 AWG
RMK-4-BCL
XSK-4-BCL
1 #10 AWG
3 #14 AWG
Part Name: XSK-DEBCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi from front side.
RMK-5-BCL
XSK-5-BCL
1 #10 AWG
4 #14 AWG
RMK-6-BCL
XSK-6-BCL
1 #14 AWG
5 #16 AWG
8
8
6
5
RMK-7-BCL
XSK-7-BCL
1 #14 AWG
6 #16 AWG
12
9
8
5
10
RMK-8-BCL
XSK-8-BCL
1 #14 AWG
7 #16 AWG
RMK-9-BCL
XSK-9-BCL
1 #14 AWG
8 #16 AWG
RMK-12-BCL
XSK-12-BCL
1 #14 AWG
11 #16 AWG
XSK-DEBCL; A non-metallic double ended connector which
accepts a mating connector on either end. The same locking
sleeve also mates to both ends. This connector utilizes a facial
o-ring seal to the bulkhead.
LOW PRESSURE
HIGH PRESSURE
O-Ring (2-131)
XSK-DEBCL
VISUAL
INDEX
6
5
XSK-1/0-DEBCL
1 #1/0
XSK-1-DEBCL XSK-6/8-DEBCL XSK-2-DEBCL
1 #8 AWG
1 #6 AWG
1 #10 AWG
1 #8 AWG
1 #14 AWG
XSK-3-DEBCL
1 #10 AWG
2 #14 AWG
XSK-4-DEBCL
1 #10 AWG
3 #14 AWG
50-27 (REV 0704)
XSK-5-DEBCL
1 #10 AWG
4 #14 AWG
XSK-6-DEBCL
1 #14 AWG
5 #16 AWG
6
5
XSK-7-DEBCL
1 #14 AWG
6 #16 AWG
VMK-FS AND ASSOCIATED PARTS
REVERSED RUBBER MOLDED
IN-LINE SERIES
Material: Special Neoprene, Molded
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
2.6
VMK-MP
VMK-FS
VISUAL
INDEX
VMK-1/0-FS
1 #1/0
(Cable: 1/0 Welding)
VMK-1-FS
1 #8
(Cable: 8/1SO)
VMK-6/8-FS
1 #6
1 #8
(Cable: 8/2SO)
VMK-2-FS
1 #14
1 #16
(Cable: 18/2SO)
VMK-3S-FS
1 #14
2 #8
(Cable: 10/3SO)
VMK-3-FS
1 #14
2 #16
(Cable: 18/3SO)
VMK-4-FS
1 #14
3 #16
(Cable: 18/4SO)
VMK-5-FS
1 #14
4 #16
(Cable: 18/5SO)
VMK-FS R/A
VMK-6-FS
1 #14
5 #16
(Cable: 18/6SO)
VMK-7-FS
1 #14
6 #16
(Cable: 18/7SO)
VMK-8-FS
1 #14
7 #16
(Cable: 18/8SO)
VMK-12-FS
1 #14
11 #16
(Cable: 18/12SO)
WOC CONNECTORS
Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprene
jacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.
Part Names: VMK-FS WOC, VMK-MP WOC
Material: Special Neoprene, Molded
Contacts: Brass, Hard Gold Plated per ASTM-B-488
Voltage Rating: 600 VDC-contact factory for higher voltage requirements
Pressure Rating, Mated: up to 20,000 psi
LOCKING SLEEVES
DUMMY CONNECTORS
K-MLS-D (AVAILABLE FOR VMK-MP, VMK-MP WOC)
K-FLS-D (AVAILABLE FOR VMK-FS, VMK-FS-R/A, VMK-FS WOC)
Notes: Specify number of conductors when ordering
VMK-FSD MATES TO VMK-MP
VMK-MPD MATES TO VMK-FS & VMK-FS R/A
Material: Special Neoprene, Molded
Pressure Rating, Mated:
VMK-FSD-LP (LOW PRESSURE < 4,000 PSI, NO CONTACT REQUIRED)
VMK-FSD-HP (4,000-20,000 PSI CONTACT IS REQUIRED)
VMK-MPD (20,000 PSI, NO CONTACT REQUIRED)
50-28 (REV 0704)
VMK-FS AND ASSOCIATED PARTS
MATEABLE BULKHEAD CONNECTORS
BULKHEAD CONNECTORS
(MATES TO VMK-FS & VMK-FS-R/A & VMK FS WOC)
Dummy Connector VMK-FSD
Part Name: VMK-BCL
Material: 316 Stainless St.; Internal Insulation: Special Neoprene
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
Part Name: VSK-BCL
Material: Glass Reinforced Epoxy
Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488
Pressure Rating, Mated: up to 20,000 psi
VMK-BCL; Special Insulating neoprene is permanently molded
to the metal shell. These types of connectors are used where
physical abuse would be too great for the non-metallic (glass
reinforced epoxy) series. The VMK BCL has a locking sleeve
provision and utilizes a facial O-ring seal to the bulkhead.
VSK-BCL; One of our oldest connectors in the non-metallic
series, with male pin as shown. Connector is one homogeneously molded unit. Available with different thread lengths as
indicated. The VSK BCL has a locking sleeve provision and
utilizes a facial O-ring seal to the bulkhead.
Mounting Torque
130 inch lbs.
Mounting Torque
130 inch lbs.
.87
.87
VMK-BCL
VSK-BCL
Mounting Torque
130 inch lbs.
VISUAL
INDEX
1.25
VSK-BCL LT
VMK/VSK-1/0-BCL
1 #1/0
VMK/VSK-1-BCL
1 #8
VMK/VSK-6/8-BCL
1 #6
1 #8
VMK/VSK-2-BCL
1 #14
1 #16
VMK/VSK-3S-BCL
1 #14
2 #8
VMK/VSK-3-BCL
1 #14
2 #16
VMK/VSK-4-BCL
1 #14
3 #16
VMK/VSK-5-BCL
1 #14
4 #16
VMK/VSK-6-BCL
1 #14
5 #16
NOTE: Torque values referenced in this literature assume installation into dry
metal threads. Please contact the factory for recommendations.
50-29 (REV 0704)
VMK/VSK-7-BCL
1 #14
6 #16
VMK/VSK-8-BCL
1 #14
7 #16
VMK/VSK-12-BCL
1 #14
11 #16
SPECIAL ASSEMBLIES
CABLE MOLDS AND CABLE SPLICES
SPECIAL ASSEMBLIES
Material: Neoprene Molding per B/A X-5727 or Polyurethane; black per
MIL-M-24041
Note: Length and geometric shape may vary depending on cable diameter.
WYE MOLDS
AVAILABLE
MOLDS
A
B
C
Y-30
2 3/4 Inches
1 5/8 Inches
5/8 Inches
Y-40
4 7/8 Inches
3 1/2 Inches
1 Inches
Y-50
6 3/4 Inches
4 Inches
1 1/2 Inches
Y-70
9 1/2 Inches
5 1/2 Inches
2 Inches
B
C
A
BARREL MOLDS
AVAILABLE
MOLDS
D
E
B-30
2 Inches
1 1/4 Inches
B-40
4 Inches
1 3/4 Inches
B-50
6 1/2 Inches
2 3/4 Inches
B-70
8 1/2 Inches
3 1/2 Inches
∅E
D
50-30 (REV 0704)
LOCKING SLEEVES
PART NUMBERING
A
SIZE
-
FLS
(F) FEMALE OR (M) MALE
LOCKING SLEEVE
-
D
MATERIAL
(D) DELRIN, BLACK - STANDARD
(S) STAINLESS STEEL
(B) BRONZE; CA 630
(X) LONG
(TI) TITANIUM
SEA CON®’S range of locking sleeves are available in Black Delrin (D), standard, previously standard: plastic or stainless
steel(S). as shown on next page. Other materials may be available by special order.
USES: Assists in avoiding accidental disconnection. The long locking sleeves are used to minimize flexing stress being
applied to the electrical conductor terminations when the cable is flexed.
CABLE
Or solid rubber for dummy
RUBBER MOLDED CONNECTOR
FEMALE LOCKING SLEEVE
(Long)
For use with straight connectors only.
This long type of locking sleeve helps
to eliminate conductor breakage at
termination joint by eliminating flexing
at joint area.
RIGHT ANGLE CONNECTOR
RUBBER MOLDED CONNECTOR
FEMALE LOCKING SLEEVE
This type of locking sleeve can be
used with straight or right angle
connectors.
BULKHEAD CONNECTORS
MALE LOCKING SLEEVE
RUBBER MOLDED CONNECTOR
Notes: Cable diameter must be specified when ordering (long -X) Locking Sleeves.
X Size only uses 1/2 inch cable or smaller.
50-31 (REV 0704)
LOCKING SLEEVES
1.70
.60
SEA CON
A-FLS-D
0.60 ∅
A-MLS-D
1.70
1.00
SEA CON
F-FLS-D
0.80 ∅
F-MLS-D
2.80 *
1.48
SEA CON
VSF-FLS-D
0.80 ∅
VSF-MLS-D
1.30
.40
1.00 ∅
G-FLS-D
G-FLS-S
G-MLS-D
G-MLS-S
2.90 *
.40
1.00 ∅
G-FLS-X
G-MLS-D
1.80
.70
SEA CON
K-FLS-D
K-FLS-S
1.50 ∅
K-MLS-D
K-MLS-S
3.60 *
.70
SEA CON
K-FLS-X
Notes:
*
K-MLS-D
VSF-FLS-D, G-FLS-X, K-FLS-X length will vary, depending on cable diameter.
50-32 (REV 0704)
1.50 ∅
RUBBER MOLDED
QUICK REFERENCE MATING TABLE
FEMALE SOCKET
IN-LINE
RMA-FS
RMA-FS R/A
RMA-FS SL
VMA-FS
VMA-FS R/A
VMA-FS SL
MATEABLE MALE
PLUG INLINE
RMA-MP
RMA-MP SL
VMA-MP
MATEABLE
METAL SHELL
BULKHEAD
MATEABLE GLASS REINFORCED
EPOXY
BULKHEAD
RMA-BCL
XSA-BC, XSA-BCL
XSB-BCL
XSC-BC, XSC-BCL
VMA-BCL
VSA-BC, VSA-BCL
VSB-BCL
VMA-MP SL
RMF-FS
RMF-FS R/A
RMF-MP
Not Available At
This Printing
XSF-BC, XSF-BCL
XSFDE-BCL (Formerly XSDE-BCL)
VMF-FS
VMF-FS R/A
VMF-MP
VMF-BCL
VSF-BCL
LMG-FS
LMG-FS R/A
LMG-MP
Not Available
This Printing
LSG-BC, LSG-BCL
LSG-BC HP
LSG-BC-SC (Formerly LSK-BC SC)
RMG-FS
RMG-FS R/A
RMG-FS WOC
RMG-MP
XSG-BCL, XSG-BCL-P- R/A
XSG-PBC, XSG-PBCL, XSG-PBCLM
RMG-MP WOC
RMG-BCL
RMGS-BC
RMGS-BCL
VMG-FS
VMG-FS R/A
VMG-FS WOC
VMG-MP
VMG-BCL
VSG-BCL
VSG-PBC, VSG-PBCL, VSG-PBCLM
RMK-FS
RMK-FS R/A
RMK-FS WOC
RMK-MP
RMK-BCL
XSK-BCL
XSKDE-BCL
VMK-FS
VMK-FS R/A
VMK-FS WOC
VMK-MP
VMK-BCL
VSK-BCL
VMG-MP WOC
RMK-MP WOC
VMK-MP WOC
50-33 (REV 0704)
pb ^`lk
®
pb^`lk®
1700 Gillespie Way,
El Cajon, California 92020, USA.
TEL: +1 (619) 562-7071
FAX: +1 (619) 562-9706
E-Mail: [email protected]
Website: www.seaconworldwide.com
pb ^`lk
®
pb^`lk US GULF AREA SALES OFFICE
14511 Old Katy Road, Suite 300,
Houston, Texas 77079, USA.
TEL: +1 (281) 599-3509
FAX: +1 (281) 599-3517
E-Mail: [email protected]
Website: www.seaconworldwide.com
pb ^`lk
®
pb^`lk US EAST COAST SALES OFFICE
50 Airport Road,
Westerly, RI 02891, USA.
TEL: +1 (401) 348-0155
FAX: +1 (401) 348-0227
E-Mail: [email protected]
Website: www.seaconworldwide.com
pb ^`lk
®
pb^`lk FLORIDA SALES OFFICE
Building B, Suite 22,
3959 South Nova Road,
Port Orange, Florida 32127, USA.
TEL: +1 (281) 802-5504
E-Mail: [email protected]
Website: www.seaconworldwide.com
pb^`lk ADVANCED PRODUCTS, LLC
1321 Nelius Road, P.O. Box 767,
Bellville, Texas 77418, USA.
TEL: +1 (979) 865-8846
FAX: +1 (979) 865-8859
E-Mail: [email protected]
Website: www.seacon-ap.com
pb^`lk BRAZIL
Rua Conde de Bonfim 120 sala 212,
Tijuca, Rio de Janeiro,
Brazil, CEP: 20520-053.
TEL #1: +55 (21) 3592-0920
TEL #2: +55 (21) 3594-0920
CELL: +55 (21) 8849-3336
E-Mail: [email protected]
Website: www.seaconworldwide.com
pb^`lk (europe) LTD
Seacon House, Hewett Road,
Gapton Hall Industrial Estate,
Great Yarmouth, Norfolk, NR31 0RB, UK.
TEL: +44 (0) 1493-652733
FAX: +44 (0) 1493-652840
E-Mail: [email protected]
Website: www.seaconeurope.com
p m b ` f ^ i ^ p p b j _ i f b p
pb^`lk® maintains all facilities necessary to furnish complete underwater and environmental electrical connector/cable systems, including
Research and Development, Engineering, Manufacturing, Quality
Control and Pressure Testing. As well as supplying our standard ‘offthe-shelf’ items, we have the capability to design and manufacture
SPECIAL CUSTOMISED CONNECTORS AND CABLE ASSEMBLIES
to suit your individual needs.
pb^`lk GLOBAL PRODUCTION
Callejon Terrazos #8, Local 2-C,
Las Brisas 1ra. Seccion,
Tijuana, B.C., Mexico C.P. 22610.
TEL: +52 (664) 626-2726
FAX: +52 (664) 686-8922
E-Mail: [email protected]
Website: www.seaconglobal.com
Dial from U.S.A. TEL: +1 (619) 308-7901
TOLL FREE: (888) 562-7072
FAX: +1 (619) 308-7900
pb^`lk PHOENIX, LLC
15 Gray Lane, Suite 108,
Hopkinton Industrial Park,
Ashaway, RI 02804, USA.
TEL: +1 (401) 637-4952
FAX: +1 (401) 637-4953
E-Mail: [email protected]
Website: www.seaconphoenixllc.com
p b ^ ` l k
®
All reasonable efforts have been taken to ensure that the information contained herein is accurate
at the date of publication, but no representation or warranty as to the accuracy or completeness
of such information is intended or to be implied by its inclusion herein. Any and all representations
and warranties pertaining to the information and products referred to herein shall be set forth in
pb^ `lk® standard sales order form. In addition, pb^ `lk® reserves the right to make
changes to the contents hereof without notice, therefore it is suggested that at the time of inquiry,
the appropriate sales office or factory be contacted directly for verification of published specifications and products availability.
© 2012 pb^`lk ®
ALL RIGHTS RESERVED