TM600 Series Digital-Transmitter-Monitor

TM600 Series Digital-Transmitter-Monitor
TM631/TM632/TM635 Proximity Digital Transmitter-Monitor
(Shaft Vibration, Thrust Position and Speed)
The TM631/TM632/TM635 digital vibration transmitter
Features
monitor is ideal for monitoring machine vibration using
proximity probes. The monitor contains redundant relay
9
outputs and 4-20mA transmission, it can interface to a
PLC or DCS system. The monitor works without probe
driver. Using Provibtech’s unique technology, the monitor
can interface with almost any proximity probe system
without hardware changes.
Interface with almost any manufacture’s
proximity probe system
9
Works without probe driver
9
Modbus RTU output
9
Redundant 4-20mA output
9
Measure shaft vibration, thrust position, or
speed
Applications include:
9
9
Full digital field-configuration
Turbines
9
9
Dual alarms (SPDT)
Compressors
9
9
LED indication of system OK, Alert, Danger,
Motors
9
Pumps
9
Fans
9
Blowers
9
9
Buffered Output for condition monitoring
Centrifuges
9
9
Aluminum case for RFI/EMI reduction
Generators
9
9
Digital condition monitoring (optional)
Turbochargers
and Bypass
9
Local and remote RESET/BYPASS and
Trip-multiply
Module Type：
9
Vibration Monitor Module
9
Thrust Position Monitor Module
9
Speed Monitor Module
9
Phase Reference Monitor module
ProvibTech
Phone: +1-713-830-7601 ● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com 7
TM600 Series Digital-Transmitter-Monitor
Specifications
Modbus:
Electrical
Power Supply:
RS485 Modbus RTU
+24VDC:
18-30VDC, @150mA; isolation: 1000VDC
Frequency Response (-3dB):
Not isolated (use TM691 for isolation)
Software programming (TM600-CFG and TM691):
Alert and danger set-point, time delay
Nominal frequency:
2 ~ 4.0 KHz
ZERO and Full-Scale calibration
Low frequency:
0.5 ~ 100Hz
Full-scale high and low setup
Alarm latching/ non-latching, energized/ de-energized
Proximity probe Interface:
Sensitivity:
Alarms programmable with alert, danger or system ok
5mm and 8mm probe: 8 mV/μm (200 mv/mil)
Probe selection, linearization, and system calibration
11mm probe:
Monitor function change: vibration, position, or speed
4 mv/μm (100 mv/mil)
Modbus communication setup
Buffered Output:
Original, un-filtered signal
Trip-multiply setup
Impedance:
150Ω
Real-time bar-graph and alarms
Maximum cable distance:
300m (1000ft)
Configure speed monitor to phase reference only
Sensitivity:
same as the sensor
monitor
Local BNC connection and terminal block
4-20mA Output:
3 layers of password protection
Digital Condition Monitoring
Dual 4-20mA, sourced (loop power not required)
Maximum load resistance:
380Ω
Terminals
Modbus-TCP interface in TM691
Software PCM360-LT
Alarm Setup:
Range:
0 ~ 100% FS.
Work with PCM360-LT plant condition management
Accuracy:
±0.1%.
software
Dynamic waveform:
Relays:
Seal:
Epoxy
Real-time vibration data, 2000 sets per data
Capacity:
0.2A/240VAC, 0.4A/110VAC or
acquisition.
2.0A/24VDC, resistive load
Relay type:
SPTD
Isolation:
1000VDC
LED Machine Condition Indicator:
OK: System OK and Digital Transmission indication
ALM (yellow): Vibration over ALERT level
Alarms:
Up to 100 alarms can be stored in TM600
Trend:
Up to 1000 trend data can be stored in TM600.
Spectrum:
Up to 800 lines of resolution.
ALM (red): Vibration over DANGER level
BYP: System in BYPASS
RESET/BYPASS:
Front panel push button
Remote RESET/BYPASS terminals
Trip Multiply:
Double multiply or Triple multiply set in TM600-CFG
Short Trip/Multi terminal to COM terminal on TM691,
System alarm level will increase by a factor of 2 or 3
(TM631 only)
ProvibTech
Phone: +1-713-830-7601 ● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com 8
TM600 Series Digital-Transmitter-Monitor
Physical
Dimension:
82mm (3.23″)
Height:
See figure below
2.0lb (1.0kg)
49
55
POWER
(+ -)
DANGER
ARM
NO
BUF
NC
ALERT
ARM NO
NC
BYP
OK
ALM
COM
SHELD
-24V
SIG
PWR
PROVIBTECH
COM
(2)+
(1)+
4-20mA 4-20mA SHELD
RST
RESET
BUF
Weight:
110
121
Rail Mounting
Environmental
Temperature:
Operation:
-30℃ ~ +70℃
Storage:
-40℃ ~ +100 ℃
Humidity:
90% non-condensing
Case:
Aluminum
ProvibTech
Phone: +1-713-830-7601 ● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com 9
TM600 Series Digital-Transmitter-Monitor
TM691 System Integration Module
TM691 is a system integration module. Each system must
have a TM691 module only and can have up to 6 TM600
modules.
Specifications
Electrical
Power Supply:
TM691 Features
9
9
Display alarm information and record alarm
+24VDC:
18-30VDC, @150mA; isolation: 1000VDC
BUS
events of all modules in system.
Include phase reference interface and remote
Display real time value and status of all
reset/bypass interface etc.
modules in system.
9
9
Calibrate 4-20mA output and adjust the
MODBUS
Alarm and Danger setpoints of all modules
MODBUS-RTU and MODBUS-TCP
The TM691 has a RS485 port and an Ethernet port
in the field.
which can be used to communicate to TM600-CFG
Provides remote reset/bypass interface and
software or condition management software.
remote trip multiply interface for all modules
Ethernet：10Mbps，IEEE802.3
in system.
9
Provides phase reference input interface for
all modules in system.
9
OLED Screen：
Blue
Resolution：128*64
Interface with condition management
software
LED Machine Condition Indicator:
OK：System OK indication
ALM (yellow): Vibration over ALERT level
ALM (red): Vibration over DANGER level
BYPASS：System in BYPASS
TRX：Digital transmission active
OK Relays:
Seal:
Epoxy.
Capacity:
0.2A/240VAC,
0.4A/110VAC
2.0A/24VDC, resistive load
Relay type:
SPTD
Isolation:
1000VDC
Push Buttons:
SET: Save, confirm or next item
∧/∨: Change numbers, letters, options or the cursor
position
＜/＞: Change the cursor position
ProvibTech
Phone: +1-713-830-7601 ● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com 32
TM600 Series Digital-Transmitter-Monitor
Ordering Information
RESET/BYPASS:
TM691-B00-G00
Front panel push-button
Remote RESET/BYPASS terminals
System Integration Module
Phase reference input:
The interface could provide phase reference information
to all modules in the system or output signal of phase
BXX: Power Supply
B00*: +24VDC
GXX：Mounting
G00*: DIN rail mounting
reference module in system.
* Denotes factory default.
Physical
Dimension:
Optional Accessories
82mm (3.23″)
Height:
Weight:
See figure below
TM600-CFG-K
2.0lb (1.0kg)
The TM600 configuration and calibration software kit
POWER
-
9
-
MOD_l1
+
49
55
MOD_O
+
-
MOD_l2
+
-
BUS
110
121
TM600 -CFG configuration and calibration software
CD
+
ETH
SET
PROVIBTECH
TRX
OK
ALM
(2)+
+
-
(1)+
COM
RST/
4-20mA
4-20mA SHELD
PHASE
BYP
-24V
PWR
SIG
COM
COM TRIP_MSHELD
NC
ARM
RESET
NO
BYP/TRIP
BUF
includes:
9
Network cable
TM900
Power converter with isolation. Converts 95-250 VAC into
24VDC and is capable of powering up to 7 TM600
modules.
Rail Mounting
BUS Cable
TM695-08:
70mm Cable, used to connected BUS
interface of TM691 to BUS2 interface of TM600 or
connected BUS1 interface of TM600 to BUS2 interface of
another TM600.
Environmental
Temperature:
Operation:
-30℃ ~ +70℃
Storage:
-40℃ ~ +100 ℃
Humidity:
90% non-condensing
Case:
Aluminum
ProvibTech
Phone: +1-713-830-7601 ● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com 33

Download Report