DET NORSKE VERITAS - kabel

DET NORSKE VERITAS
TYPE APPROVAL CERTIFICATE
CERTIFICATE NO. E-13037
This is to certify that the
Data transmission cables and systems
with type designation(s)
SIENOPYR PROFIBUS M-02Y(ST)CHX
Issued to
Prysmian Kabel und Systeme GmbH
Neustadt b. Coburg, Germany
is found to comply with
IEC 60754-1/2 (2011-11)
IEC61034-1/2 (2005-04/2005-04)
IEC 60332-1
Application
SIENOPYR PROFIBUS
Voltage (kV)
Temp. class (°C)
0,1
80
This Certificate is valid until 2017-12-31.
Issued at Høvik on 2014-02-07
for Det Norske Veritas AS
DNV local station: Essen CMC Southern Germany
Digitally Signed By: Laumann, Marit
Location: DNV Høvik, Norway
Approval Engineer: Marta Alonso Pontes
Signing Date: 2014-02-12
Marit Laumann
Head of Section
This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid.
The validity date relates to the Type Approval Certificate and not to the approval of equipment/systems installed.
If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such
person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum
compensation shall never exceed USD 2 million. In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers,
employees, agents and any other acting on behalf of Det Norske Veritas.
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Høvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: 2013-10
www.dnv.com
Page 1 of 3
Certificate No.: E-13037
827.50
File No.:
Job Id.:
262.1-008096-3
Product description
Type:
M-02Y(ST)CHX 1 x 2 x 0,35 100 V
Conductors:
Core insulation:
Screen
Outer sheath:
Plain stranded copper
Foamed PE
Tinned copper wires
SHF2
Number of cores x
conductor cross-section
mm2
Overall dimensions
1 x 2 x 0,35
10,3±0,5
mm
Table 107- Fieldbus cable specifications (IEC 61158-2 ed.1)
Cable parameter
Impedance
Capacity
Resistance
Conductor cross-sectional area
Color of sheath non-IS
Color of inner cable conductor A (RxD/TxD-N)
Color inner cable conductor B (RxD/TxD-P)
Type A
135 to 165 W
(f = 3 to 20MHz)
< 30 pF/m
< 110 W/km
2
≥ 0,34 mm
Violet
Green
Red
Type B
100 to 130 W
(f > 100kHz)
< 60 pF/m
Not specified
2
≥ 0,22 mm
Not specified
Not specified
Not specified
M-02Y(ST)CHX
150 +/- 15 W
(f = 3 to 20MHz)
max. 30pF/m (at 800 Hz)
max. 110 W/km
0,35 mm2
Black
Red
Green
Application/Limitation
By the termination of the cables the total strings of the cable to be kept through into the termination point as for coax cables.
Type Approval documentation
Specification Nr. 50 PS 116 dated 2000-04-20 and 2013-12-09.
Termination instruction 6GK1500-0EA02 dated 1999
Test reports: PF5-13/96 (96-506-E, VA 2148) dated 1997-08-12 and 5BG6951 dated 2000-04-20.
Technical data sheet: SIENOPYR-FR PROFIBUS M-02Y(ST) CHX dated 2008-08-25
Tests carried out
Standard
IEC 60754-1
Release
2011-11
IEC 60754-2
2011-11
IEC 61034-1/2
2005-04
IEC 60332-1
2004-07
General description
Test on gases evolved during combustion of
materials from cables - Part 1: Determination of
the halogen acid gas content
Test on gases evolved during combustion of
materials from cables - Part 2: Determination of
acidity (by pH measurement) and conductivity
Measurement of smoke density of cables
burning under defined conditions –
Test apparatus, procedure and requirements
Tests on electric and optical fibre cables
under fire conditions – Part 1-1:Test for vertical
flame propagation for a single insulated wire or
cable – Apparatus
Limitation
Low Halogen:
<0,5% Halogen
Halogen free:
pH > 4,3
Conductivity < 10μS/mm
Low smoke
Light transmittance >60%
Flame retardant small
scale
Marking of product
♦ - SIENOPYR PROFIBUS M-02Y(ST)CHX 1x2x0,35 mm
2
150 OHM – IEC 60332-1
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Høvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: 2013-10
www.dnv.com
Page 2 of 3
Certificate No.: E-13037
827.50
File No.:
Job Id.:
262.1-008096-3
Periodical assessment
The scope of the periodical assessment is to verify that the conditions stipulated for the Type approval is complied with and that
no alterations are made to the product design or choice of materials.
The main elements of the periodical assessment are:
·
Inspection on factory samples, selected at random from the production line (where practicable)
·
Results from Production Sample Tests (PST) and Routines (RT) checked (if not available tests according to PST and RT to
be carried out)
Review of type approval documentation
·
·
Review of possible change in design, materials and performance
·
Ensuring traceability between manufacturer’s product type marking and Type Approval Certificate.
Periodical assessment shall be performed at least every second year.
END OF CERTIFICATE
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Høvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: 2013-10
www.dnv.com
Page 3 of 3