SRS FMS-CZ80-162604 r2 - Support

SOFTWARE RELEASE
SPECIFICATION
FMS-CZ80-162604
(Rev. 2)
CashCode A Crane Co.
Company.
2720 Steeles Ave. West,
Units 2-3
Concord, Ontario
Canada L4K 4S3
Tel: 800-584-2633
Fax: 800-593-2633
Web Address: www.cashcode.com
Email: [email protected]
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Manufacturer
Product
Interface
Release Date
File Name
Version
Control Firmware
Software version
(as per MDB expansion Command)
Country Code
Decimal Place
Scaling Factor
Validation Firmware
Configuration File
Notes Supported
15.
16.
17.
Bill Set Description
Note Directions
Memory Device
18.
Switch Settings
CashCode
®
FMS Bill Validator / one
MDB Protocol
15 Sep 2014
FMS-CZ80-162604.cfs
FMS-CZ80-162604
FMSMS-0006-16
1600
1203
2
10000
FMSVS-CZ326
FMSCS-CZ80-04
Czech Koruna (CZK)
100, 200, 500, 1000, 2000, 5000
BSD-CZK6-C
4 way
Onboard Flash Memory, Atmel Serial Data Flash
Atmel AT45DB021B-SU or AT45DB021D-SH or future
applicable revisions
Switch Bank # 1
SW 1.1
SW 1.2
SW 1.3
SW 1.4
SW 1.5
SW 1.6
SW 1.7
SW 1.8
Switch Bank # 2
SW 2.1
SW 2.2
SW 2.3
ON State
Reserved
100 CZK Enabled
200 CZK Enabled
500 CZK Enabled
1000 CZK Enabled
2000 CZK Enabled
5000 CZK Enabled
Accept All
ON State
Sleep Mode1 Disabled
Sleep Mode2 Disabled
Reserved
SW 2.4
Service
OFF State
Reserved
100 CZK Disabled
200 CZK Disabled
500 CZK Disabled
1000 CZK Disabled
2000 CZK Disabled
5000 CZK Disabled
Reject Unfit Bills
OFF State
Sleep mode 1 Enabled
Sleep mode 2 Enabled
Reserved
To work with a
“Host Machine Controller”
Statistics
Default Setting
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
Note SW 1.8: Both settings use the same security algorithms. On setting attempts to accept all
legitimate bills even if there is some damage to them. Off setting rejects legitimate but damaged
bills. Examples are bills that have been glued or have large holes or pieces missing.
SRS FMS-CZ80-162604 r1
Page 1 of 3
© CashCode Co. Inc.
19.
Error Codes
SOFTWARE
HARDWARE
Number of Status
Light Flashes
20.
Error Description
1 red on black
Cassette is removed from bill validator
2 red on black
An error occurred during CPU exchange with
magnetic board
3 red on black
Cassette is full
4 red on black
Mechanical jam in the cassette or stacker motor
failure
5 red on black
Failure of dielectric sensors
6 red on black
Failure of optical sensors
7 red on black
Failure of inductive sensors
8 red on black
Failure of transporting motor
9 red on black
Speed of transporting motor is too fast
10 red on black
Failure in alignment mechanism
11 red on black
Bill pathway is not empty
12 red on black
Bill jammed in entry slot of the cassette. No credit
given
13 red on black
Overload of transport motor
14 red on black
System error
1 green
Unable to write program memory
2 green
Firmware integrity error
3 green
Wrong memory card
4 green
Security error
USB update feature
– USB update feature has been corrected to support software download with control firmware ver. 08
or later.
SRS FMS-CZ80-162604 r1
Page 2 of 3
© CashCode Co. Inc.
VERSION HISTORY of FMS-CZ80-162604
20.
Version History – Control Firmware
FMSMS-0006-16 – Improved processing of optical channel for better performance at low
temperature.
FMSMS-0006-15 – 1) BV level 2 and FTL support commands have been implemented;
2) Firmware update via MDB FTL has been introduced.
FMSMS-0006-14 – 1) Improved algorithm of bill returning from Escrow;
2) Improved chip select function for future proofing.
FMSMS-0006-13 – Improved control of motor speed to optimize temperature conditions.
FMSMS-0006-12 – Improved Software download via front USB.
FMSMS-0006-11 – 1) BV will go to Sleep mode after 5 sec. without polling from Error/Jam states;
2) BV reports Jam if input sensor is covered in Disable state.
FMSMS-0006-10 – Modified control software based on version FMSMS-0006-06 to resolve incorrect
reads of flash program memory under some conditions.
FMSMS-0006-09 – Modified control software to resolve incorrect reads of flash program memory
under some conditions.
FMSMS-0006-08 – Enhanced processing of transparent window on a bill
FMSMS-0006-07 – Improved handling of aligning mechanism for better performance on the bills of
large size (50 GBP)
FMSMS-0006-06 – Improved handling of wake up line to prevent switching to endless Sleep mode
FMSMS-0006-05 – Enable/Disable denominations by DIP switches has been improved to introduce
integrated switches mapping
FMSMS-0006-04 – Interval between bill insertion in Sleep mode and sending Wake up signal to Host
has been shortened to 200 ms.
FMSMS-0006-03 – Bill aligning sequence has been improve to enhance acceptance rate
FMSMS-0006-02 – Initial release
21.
Version History – Validation Firmware
FMSVS-CZ326 – Initial release for Czech Korun
22.
Version History – Configuration Firmware
FMSCS-CZ80-04 – Initial release
SRS FMS-CZ80-162604 r1
Page 3 of 3
© CashCode Co. Inc.

Download Report