PDF Download

Technical Information
Technical Information
PREPARATION OF PROCESSING
senotherm
- UHT-HYDRO
senotherm -UHT®®
Product series/Article No.:
3590
Product series/Article No.:
-3590-
Hydro
STORAGE
Paint:
Shelf life of the paint depends on the ambient temperature. If stored under optimum conditions, i.e.
10-25 °C in sealed original packaging, the shelf live is 6 month. Higher temperatures may reduce shelf
life to 3 months. Material must be protected against heat, frost und direct solar radiation.
Hardener:
Since the hardener is categorized as highly flammable the following storage conditions are important:
- Keep tightly closed.
- Keep away from heat, sparks and open flame
PREPARATIONS FOR PROCESSING
Prior to processing material must be brought to room temperature and must be stirred thoroughly.
Paint:
Must be homogenized thoroughly by stirring until any potential sediment has been completely
dissolved.
Hardener:
No homogenization needed.
Maturing:
QW-4.2-Nr.528e-1-08/08
QW-4.2-Nr.501e-1-08/08
The whole quantity of hardener is to be poured into the paint at the specified mixing ratio by weight.
Normally, our supplies are arranged in such a way that the quantities of paint and hardener exactly fit
with each other, i.e. one can of hardener contains the adequate quantity for one drum of paint.
Agitation of both components, paint and hardener, must start within 5 minutes after the addition of the
hardener. The mixture of paint and hardener must then be stirred for 45 minutes with a suitable mixer
and an appropriate stirring disc at 2000 rpm. During this process the temperature of the material
increases, however, should not exceed 55° C after 45 minutes.
Due to the rising temperature and the high speed it is necessary to cover the container during
agitation, as otherwise particles of paint may dry at the sides of the container or the material may
overflow.
After agitation, the container with the material must be closed tightly immediately in order to avoid any
drying of paint particles at the sides.
WEILBURGER Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.de
WEILBURGER
Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.com
Amtsgericht Limburg a.d. Lahn
HRB 3397 | Ust.-ID-Nr. DE 112637840
Managing Directors:
Frank Gläser, Antonio Cuddemi
Amtsgericht Limburg a.d. Lahn
page3397
1 of| Ust.-ID-Nr.
5
HRB
DE 112637840
Managing Director: Frank Gläser
page 1 of 5
PREPARATION OF PROCESSING
Technical Information
®
Product series/Article No.:
senotherm -UHTHydro
3590
senotherm® - UHT-HYDRO
Product series/Article No.:
-3590-
COOLING:
Directly after maturing, the temperature of the material is too high for application. To achieve best
results it is recommended to let the matured material cool down to room temperature. Depending on
the ambient temperature, this may take over night.
FILTRATION:
As the material is fast airdrying there might be dry particles of coating at the sides of the containers.
As these dried particles can not be redissolved again, it is recommended to filter the matured coating
through 250 µm (60 mesh) prior to application.
SUBSTRATE:
Sand blasting with alumina (corundum, Al2O3) having a particle size of 80-100 mesh should result in a
surface roughness of at least Ra = 2.5 µm. This is the recommended optimum for a good adhesion of
the coating. Shot blasting is well suited.
A metallically pure substrate free from grease, rust, blasting residues and other contaminations is a
basic requirement for good coating results. Alkaline detergents or organic solvents can be used for
degreasing.
POT LIFE:
QW-4.2-Nr.528e-1-08/08
QW-4.2-Nr.501e-1-08/08
During maturing a reaction is started which will harden the coating completely.
As this process also continues in the drum the material has a limited shelf life of 48 hours.
After that time, the viscosity increases and the material becomes ‘muddy’ which indicates that it can
not be used anymore.
This process can be slowed down and the shelf life prolonged by cooling the matured material.
Careful: Don’t cool below 5 °C !
Temperatures exceeding 20 °C a well as other altering condition may reduce pot life.
WEILBURGER Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.de
Amtsgericht Limburg a.d. Lahn
HRB 3397 | Ust.-ID-Nr. DE 112637840
Managing Directors:
Frank Gläser, Antonio Cuddemi
WEILBURGER Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.com
Amtsgericht Limburg a.d. Lahn
HRB 3397 | Ust.-ID-Nr. DE 112637840
Managing Director: Frank Gläser
page 2 of 5
page 2 of 5
Technical Information
Technical Information
PREPARATION OF PROCESSING
senotherm - UHT-HYDRO
®
Product series/Article No.:
Product series/Article No.:
®
senotherm -UHTHydro
-3590-
3590
AGITATORS:
Motor power: 1.1 kW
Working speed: 520-3640 1/min
Capacity: containers of 0 to 25 kg
QW-4.2-Nr.501e-1-08/08
QW-4.2-Nr.528e-1-08/08
Speed indicator: analogue
WEILBURGER
Coatings
GmbHGmbH
WEILBURGER
Coatings
Ahaeuser
Weg
12-22
| D-35781
Weilburg/Lahn
(Germany)
Ahaeuser
Weg
12-22
| D-35781
Weilburg/Lahn
(Germany)
Tel.:+49
+49
6471
315-0
+49 6471
315-116
Tel.:
6471
315-0
| Fax:| Fax:
+49 6471
315-116
E-Mail:[email protected]
[email protected]
E-Mail:
Internet:www.weilburger-coatings.com
www.weilburger-coatings.de
Internet:
Amtsgericht
Limburg
a.d.a.d.
LahnLahn
Amtsgericht
Limburg
HRB
3397
| Ust.-ID-Nr.
DE 112637840
HRB
3397
| Ust.-ID-Nr.
DE 112637840
Managing
Directors:
Managing
Director:
Frank Gläser
Frank Gläser, Antonio Cuddemi
page 3 of 5
page 3 of 5
Technical
Information
Technical
Information
PREPARATION OF PROCESSING
senotherm® - UHT-HYDRO
Product series/Article No.:
-3590-
Product series/Article No.:
senotherm®-UHTHydro
3590
Motor power: 2.2 kW
Working speed: 0 – 5500 1/min
Capacity: Containers of 0 – 40 kg
QW-4.2-Nr.528e-1-08/08
QW-4.2-Nr.501e-1-08/08
Speed indicator: digital
WEILBURGER Coatings GmbH
AhaeuserCoatings
Weg 12-22
| D-35781 Weilburg/Lahn (Germany)
WEILBURGER
GmbH
Tel.: Weg
+49 12-22
6471| 315-0
+49 6471(Germany)
315-116
Ahaeuser
D-35781| Fax:
Weilburg/Lahn
[email protected]
Tel.: E-Mail:
+49 6471
315-0 | Fax: +49 6471 315-116
Internet:
www.weilburger-coatings.de
E-Mail:
[email protected]
Internet: www.weilburger-coatings.com
Amtsgericht Limburg a.d. Lahn
HRB 3397
| Ust.-ID-Nr.
Amtsgericht
Limburg
a.d. Lahn DE 112637840
Managing
Directors:
HRB 3397
| Ust.-ID-Nr.
DE 112637840
FrankDirector:
Gläser,Frank
Antonio
Cuddemi
Managing
Gläser
page 4 of 5
page 4 of 5
Technical Information
Technical Information
PREPARATION OF PROCESSING
Product series/Article No.:
®
®
senotherm
senotherm-UHT - UHT-HYDRO
Hydro
3590
Product series/Article No.:
-3590-
Stirring discs:
10 kg drum = 9 cm disc diameter
25 kg drum = 12,5 cm disc diameter
QW-4.2-Nr.528e-1-08/08
QW-4.2-Nr.501e-1-08/08
Manufacturers of suitable agitators and stirring discs are e.g. Co. Pendraulik or Co. VMA-Getzmann
GmbH
3590-hydro-preparation of processing-01
30.06.2010/hh-sz-sm
WEILBURGER Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.de
WEILBURGER Coatings GmbH
Ahaeuser Weg 12-22 | D-35781 Weilburg/Lahn (Germany)
Tel.: +49 6471 315-0 | Fax: +49 6471 315-116
E-Mail: [email protected]
Internet: www.weilburger-coatings.com
Amtsgericht Limburg a.d. Lahn
HRB 3397 | Ust.-ID-Nr. DE 112637840
Managing Directors:
Frank Gläser, Antonio Cuddemi
Amtsgericht
page
5 of 5 Limburg a.d. Lahn
HRB 3397 | Ust.-ID-Nr. DE 112637840
Managing Director: Frank Gläser
page 5 of 5