PVL1300 · · · Elpress AB P.O. Box 186 SE-872 24 KRAMFORS, Sweden Tel: +46 612 71 71 00 Fax: +46 612 71 71 51 E-mail: [email protected] www.elpress.se · MEMBER OF LAGERCRANTZ GROUP PVL1300 - ergonomic and well balanced crimp tool with 13 tons crimp force PVL1300 is a battery powered crimp tool with 13 tons force. Uses the same crimp accessories as the other products in the 1300-System. PVL1300DB is supplied with 2 batteries. PVL1300 crimps: - Cu-conductors up to 400 mm2 - Al-conductors up to 240 mm2 - C-sleeves up to 120/120 mm2 Technical data: ergonomic design that optimizes the balanace of the tool in the users hand buzzing signal and flashing light if right pressure is not achieved LED lightning for work in dark environments possibility to document each crimp for unique service control crimp force 124 kN (13 ton) crimps/charge: 60-120 depending on size and temperature crimp time: 4-12 s depending on size working temperature -20˚C to +40˚C environmental friendly battery, Li-Ion Makita, 3.0 Ah, 18V battery charger Li-Ion Makita, charging time 22 min LED indication of charge status supplied with robust plastic case, battery, charger and instruction PVL1300DB, supplied with 2 batteries weight 5.4 kg, (incl battery) · · · Elpress AB P.O. Box 186 SE-872 24 KRAMFORS, Sweden Tel: +46 612 71 71 00 Fax: +46 612 71 71 51 E-mail: [email protected] www.elpress.net · MEMBER OF LAGERCRANTZ GROUP PVL1300 Accessories for crimping Cu with PVL1300 Crimp dies V1318 + B type dies + V1316. Integrated dies 13B38. Supplied as a pair. For hexagonal crimping of Cu terminals and connectors. If not indicated otherwise, always use inner die holder V1316 and outer die holder V1318. mm² 10 16 25 35 50 70 95 120 120 150 150 185 240 300 400 KRF/SKF Dies B8 B9 B11 B13 B14,5 B17 B20 B22 13B22* B25 13B25* 13B27* 13B30* 13B32* 13B38* No. of crimps 1 1 1 1 1 1 1 1 2 1 2 2 2 2 3 mm² 10 16 25 35 50 70 95 120 150 185 240 300 400 KRD/SKD Dies B8 B8 B9 B11 B12 B14 B16 B19 B22 13B25* 13B27* 13B30* 13B32* No. of crimps 1 1 1 1 1 1 1 1 1 2 2 2 2 mm² 10 16 25 35 50 70 95 120 150 185 240 300 DIN 46235 Dies B6DIN B8DIN B10DIN B12DIN B14DIN B16DIN B18DIN B20DIN B22DIN 13B25DIN* 13B28DIN* 13B32DIN* No. of crimps 1 1 1 1 1 1 1 1 1 2 2 2 *All dies type 13Bxx are used without die holder. mm² 10 16 25 35 50 70 95 120 150 185 240 300 400 One and two crimps. Three crimps. V1318 + BC type dies + V1316. KRT/KST Dies B7 B8.5 B10 B12 B14 B16 B18 B19 B22 B24 13B26* 13B30* 13B32* *All dies type 13Bxx are used without die holder. For oval crimping of Cu branch connectors (C-sleeves). If not indicated otherwise, always use inner die holder V1316 and outer die holder V1318. Main conductor mm² 10-6 16-10 25-16 50-16 70-50 95-70 120-95 One or two crimps made No. of crimps 1 1 1 1 1 1 1 1 1 1 2 2 2 Branch mm² 10-6 16-6 25-16 50-16 70-25 95-25 120-25 Dies BC4** BC5 BC6 BC8-9 BC11 13BC13* 13BC15* No. of crimps 1 1 1 1 1 2 2 *Used without die holders. **Die nest must be marked C4A to connect 6 mm² main to 6 mm² branch. · · · Elpress AB P.O. Box 186 SE-872 24 KRAMFORS, Sweden Tel: +46 612 71 71 00 Fax: +46 612 71 71 51 E-mail: [email protected] www.elpress.se · MEMBER OF LAGERCRANTZ GROUP PVL1300 Accessories for crimping Al with PVL1300 Punch and matrix For indent crimping of Al terminals and connectors. For 16-150 (185 solid) mm², matrix holder V1320 is used. Stranded mm² 16 25 35 50 70 95 120 150 185 240 Solid mm² 16(+25) 35 50 70 95 120 150 185 240 Matrix P13M P13M P20M P20M P20M P25M P25M P25M 13P32M* 13P32M* Punch P13D P13D P20D P20D P20D P25D P25D P25D P32D P32D No. of crimps 2 2 2 2 2 2 2 2 2 2 *used without matrix holder. For indent crimping of Al terminals type AKKxxxB/AKSxxxB and connectors type V1320 matrix holder + P13M matrix ASxxxB. + P13D punch. Stranded mm² 300 400 Matrix 13P37M* 13P37M* Punch 13P37D 13P37D *used without matrix holder. Always make two crimps, see picture. Crimp sequence. For prerounding of sector shaped Al conductors. For 16-240 mm², matrix holder V1320 is used. Stranded mm² 16 25 35 50 70 95 120 150 185 240 Solid mm² 16(+25) 35 50 70 95 120 150 185 240 Matrix 6RMR R7MR R8MR R9MR R12MR R13MR R15MR R16MR 13R18MR 13R20MR Punch 13R6DR 13R7DR 13R8DR 13R9DR 13R12DR 13R13DR 13R15DR 13R16DR 13R18DR 13R20DR Crimp dies Supplied as a pair. For hexagonal crimping of connectors for overhead conductors of Matrix holder V1320 + matrix R6MR AlMgSi (Super B) and Al 59. + punch 13R6DR. mm² 31-62 99 157 241 · · · No. of crimp 2x5 2x5 2x16 2x16 Dies B16NP B20NP 13B26* 13B32* *Used without die holders. Supplied as a pair. For hexagonal crimping of connectors for overhead ACSR conductors. Die holders V1316 and V1318 to be used. mm² 62 99 Elpress AB P.O. Box 186 SE-872 24 KRAMFORS, Sweden Tel: +46 612 71 71 00 Fax: +46 612 71 71 51 E-mail: [email protected] www.elpress.net · Outer die holder V1318 V1318 Dies Dies Steel connector (inner) Al-conector (outer) B6FE B16NP B8FE B20NP No. of crimps 2x5 2x5 MEMBER OF LAGERCRANTZ GROUP 8052-059000 V1318 outer die holder + BNP type dies + V1316 inner die holder. Inner die holder V1316 V1316
© Copyright 2024 ExpyDoc