KA LPI 27 0 0 249

By
Kit Code:
KA LPI 27 0 0
Configuration:
249
Kit composition
Q.ty
Code
Description
1
FO8RAPID-LPI
Module Rapid LPI
1
FRLI03
Wiring for Rapid LPI
Optional:
1
C08RWC01
Switch RAPID – Wireless
Application
Producer
Modell
BMW
114d 1.6 D
Mini
Cooper 1.6 D 82Kw/112hp
Cooper D 1.5 3cyl. 70Kw/95hp
Cooper D 1.5 3cyl. 85Kw/115hp
One 1.6 D 66Kw/90hp
Mini
Cabrio/Clubman
Mini Countryman
R60 Countryman
R58 Roadster
Paceman
70kw/95hp
Cooper 1.6 D
Cooper
Cooper
Cooper
Cooper
Cooper
Cooper
1.6
2.0
1.6
2.0
2.0
1.6
82Kw/112hp
D ALL4 82Kw/112hp
16V SD 105Kw/141hp cod.N47C20A
16V 82Kw/112hp
16V 105Kw/141hp
16V SD 105Kw/141hp
16V 82Kw/112hp
Standard setting:
SET
020
TH1
TH2
TH3
070
110
064
WARNING
The Rapid module F08RAPID-LPI used for this application, must has serial
number greater of 13025170.
For more information contact the Rapid support (+39)0142/9552
Revisione 1.5
1/6
24/09/2014
By
Installation Rapid
Kit installation connections
⇒
⇒
⇒
Rail pressure sensor signal.
+ 12 Volts.
GND
Connections table
Revisione 1.5
2/6
24/09/2014
By
Connection to the Rail diesel pressure signal for 3 cylinders engine
⇒
Remove the plastic engine cover.
⇒
Under the intake manifold, locate the
rail pressure sensor, attached on Rail
(in the area shown in Pict. 1)
Fig.1
⇒
Under the intake manifold, locate the
rail pressure sensor, attached on Rail
(in the area shown in Pict. 1 and 2 )
⇒
Disconnect the three-way connector of
the diesel pressure signal
Fig.2
⇒
Connect the male-pin connector of the
Rapid module wiring to the original connector
that has been disconnected from the diesel
pressure signal.
⇒
Connect the female-pin connector of
the Rapid module wiring to the Rail pressure
sensor
Fig.3
Revisione 1.5
3/6
24/09/2014
By
Connection to the Rail diesel pressure signal for 4 cylinders engine
⇒
Remove the plastic engine cover.
⇒
Under the intake manifold, locate the
rail pressure sensor, attached on Rail
(in the area shown in Pict. 1)
Fig.1
⇒
Under the intake manifold, locate the
rail pressure sensor, attached on Rail
(in the area shown in Pict. 1 and 2 )
⇒
Disconnect the three-way connector of
the diesel pressure signal
Fig.2
⇒
Connect the male-pin connector of the
Rapid module wiring to the original connector
that has been disconnected from the diesel
pressure signal.
⇒
Connect the female-pin connector of
the Rapid module wiring to the Rail pressure
sensor
Fig.3
Revisione 1.5
4/6
24/09/2014
By
Connection of the power supply
⇒
⇒
Connect the Black wire of Rapid cable to GND.
Connect the Red wire of Rapid cable to +12 volts
Final Operations
⇒
⇒
Connect the Rapid module to the wiring.
Connect the switch (C08RWC01, if bought) to the two-way connector of the wiring.
NOTE : Rapid is always on if nothing is connected to the two way connector
⇒
Place the Rapid module and the kit components far from any excessive heat sources.
Description of the digital calibration parameters of the RAPID LPI module
The RAPID LPI module can be checked by some digital parameters that can be modified by means of the device
called CALIBRATION CONSOLE (F08IP-002 code, supplied as an option).
The RAPID LPI module parameters that can be modified are:
⇒
SET: it regulates the fuel supply enhancement and therefore the increase in the performances provided by
the RAPID module. By increasing this parameter you can increase the extra amount of injected diesel, by decreasing
it you will decrease this amount.
⇒
TH1: it regulates the RAPID module activation threshold by taking the pressure signal as a reference. The
RAPID module therefore is not activated until the diesel pressure exceeds the TH1 value.
⇒
TH2: it regulates the RAPID module deactivation threshold depending on the diesel pressure signal. When
the pressure exceeds the TH2 threshold value, the RAPID LPI module decreases the amount of added diesel so that
it is not overcharged.
⇒
TH3: this parameter is not used in this application, please set it at 064 and do not vary it.
The variation of the standard pre-set parameters in the RAPID module by the manufacturer must be agreed
with DIMSPORT technical assistance. Every new calibration must be tested on the vehicle while it is running.
Notes
⇒ If you had bought C08RWC01, It is possible to commute the RAPID module from on to off in any conditions
of vehicle use, even though we recommend activating and deactivating the RAPID module when the vehicle is not
working or with a low load.
⇒ If the switch is not connected to the special 2-way connector of the RAPID module wiring, the additional
module remains constantly activated.
⇒ If you wish to use an alternative switch, please contact the technical assistance.
Revisione 1.5
5/6
24/09/2014
By
Warning
CAUTION: An excessive increase in performances could damage the engine or lead to the activation of the
vehicle electronic protections.
⇒ Please make sure that the vehicle works properly, namely the engine, before installing the Rapid module: a
performance increase could highlight some potential defects of functioning.
⇒ We do not recommend assembling the Rapid module if the engine or the injection system have already been
modified. NB: an excessive increase in performances could lead to engine damage or to activation the electronic
control unit protections.
⇒ Do not turn on the controls board if all the connectors are not connected. If you do not follow this instruction
there would not be any damages, but the control unit would memorize an error.
⇒ The Rapid module is designed for 12 to 30 Volt supply voltages, therefore make sure this limit is not
exceeded by checking, before the installation, that the battery, the regulating circuit and the alternator work
properly.
⇒ Place the RAPID module and its parts far from any excessive heat sources.
For Technical Support (Italian and English languages)
From Monday to Friday ; from 9 a.m. to 1 p.m. and from 2 p.m. to 6 p.m. (GMT +1)
Phone +39 0142 95 52
FAX + 39 0142 94 00 94
E-mail : [email protected] (Italian language)
E-mail : [email protected] (English language)
The RAPID device is used professionally on a closed circuit, therefore
Dimsport srl accepts no responsibility in terms of damages to things
or people, accidents, breakdowns, delays and/or loss of profits of any
kind provoked by an improper use of this product. In the event of
modifications of the performances cited in the vehicle registration
document, update the vehicle documents. Any operations on the vehicle
will therefore fall under the Customer’s responsibility. The RAPID
device is covered by a 36-month warranty on the manufacturing defects
and starting from the installation or purchase date only if
convalidated by a tax document.
Revisione 1.5
6/6
24/09/2014

Download Report