Ethernet POE extension over copper and POL Power Over the Line ETHERNET POE EXTENTION VDSL2 UP TO 100MBPS Features • VDD2-H-4TPW-M local modem Ethernet bridge with POL of remote modem • VDD2-H-4TPOE-S remote modem Ethernet bridge POE, Power feed Over the Line (POL) by local modem • VDSL Transmission 30a et 17a according to G.993.2 • PTN transmission over DMT modulation Maximum rates: • Asymmetrical transmission with selection of CO/CPE for the application • 100/65Mbps at 300m to • 22/2Mbps at 1,7km Maximum distance is 1,9km according to cable diameter and noise Ethernet bridge: • Local: 4 x 10/100BaseT • Remote 4 x 10/100BaseT POE PSE 802.3af/at • Transparent to 2 Kbytes (MTU) • POL power is 60W to share in 4 ports less the loss due to the distance (see curve) Power supply: • Local power in 48Vdc • Remote is power-feed by local over the line POL The VDD2-H-4TPxx is a VDSL2 modem/Ethernet bridge solution to connect and power- feed up to 4 Ethernet POE PD terminals like CATV camera, HotSpot, IP Phone…. over a single twisted copper pair. The link including Ethernet and power-feeding can reach over 1,7km. The local equipment supplies 60W on the VDSL line to power-feed the remote in POL. The remote device owns 4 Ethernet POE source port 802.3af/ at. This solution simplifies the installation of video survey and Wifi infrastructures. The VDD2-H-4TPOE-S remote modem in- Settling for « high speed » or « long reach» cludes 4 Ethernet POE source ports. These profiles, filter for impulse noise or SNR and ports comply to IEEE802.3af/at up to 30W. CO/CPE mode are selected by DIPThis remote modem is power-feed by the switches. DSL line in Power-Over-Line (POL) from the Because of the asymmetrical transmission, the selection of CO and CPE can be applied local modem local VDD2-H-4TPW-M. This local modem supply on the DSL line to Local or Remote devices. To favor the 60W to power feed the remote modem Internet distribution for Hot Spot the CO is VDD2-H-4TPOE-S with his 4 POE PSE ports. activated in local modem or to favor IP This power is attenuated by the loss of en- camera then the remote is set up as CO. ergy along the line. As the distance of the line will be longer as the power to distribute on the POE port should be lower. The loss power is depending on the copper diameter. For example 30W are available to share on the four ports at Rate in the sence 500m with a 0.5mm diamPOE to share in 4 ports selected by DIP switch eter copper, but over 1mm diameter line at 1 km the Ø 0,6mm 24AWG 0,8mm 20AWG 0,6mm 24AWG power to distribute is also 0m CO-CPE CPE-CO 60W 60W 30W. 100m 100Mbps 100Mbps 57W 47,2W 300m 500m 1,0km 1,4km 1,7km 100Mbps 65Mbps 55W 44,1W 80Mbps 40Mbps 52W 36,3W 45Mbps 20Mbps 45W 16,7W 30Mbps 8Mbps 39W 11,2W 22Mbps 2Mbps 35W 7,7W No noise measurement over 0,8mm (20AWG) cable Page 2 VDD2-H-TPW/TPOE TECHNICAL SPECIFICATIONS Transmission: POE power to share over the 4 POE ports VDSL2 over one copper pair G.993.2 Transmission profiles 30a and 17a Transport of Ethernet over VDSL2 in EFM PTM mode Ethernet Interfaces : Local VDD2-H-4TPW-M: 4 x10/100BaseT ports Remote VDD2-H-4TPOE-S: 4 x 10/100BaseT POE PSE ports. POE source IEEE802.3at PoE (PSE), up to 30W per port 60W to share at 10m. All ports are 10/100 Mbps auto-negotiation; full and half duplex, automatic MDI/MDIX. Complies to: IEEE 802.3, 802.3u,802.3x, 802.1p, 802.1Q et POE IEEE802.3af, IEEE802.3at PoE/PSE Ethernet Bridge Supports 2000 Octets (MTU) MAC address memory: 2K Settling : Per DIP-Switch for the following selection: High Speed (30a profile) /Long distance (17a profile) Source / Destination (CO/CPE) for upstream/downstream - per default VDD2-H-4TPW-M in CO for Internet access. - for IP camera VDD2-H-4TPOE-S should be set as CO to favor upstream. Inpulse Noise (filter active/unactive) SNR margin (filter active/unactive) Power supply: Input -38 to -58 VDC, consumption 90W. Protection against inversion of polarity . AC/DC 48v 120W converter as an option. Environment: Working temperature: VDD2-H-4TPW-M from -40 to +65°C, VDD2-H-4TPOE-S from -40 to +75°C Stocking de -40 to +85 °C Humidity 5 to 95% RH (non-condensed) Compliances EN60950, EN55022, CE, UL508, VCCI, FCC part 15 Class B RoHS et WEEE Case Indoor IP30. Out-door IP66 type as an option Dimensions 152 (H) x 132.8 (D) x 53.2 (W) mm Weight 1100g DIN-Rail fixing clip and wall are supplied High Speed profile Long distance profile MODEL NUMBER VDD2-H-4TPW-M CXR Anderson Jacobson Rue de l'Ornette 28410 Abondant - France T +33 (0) 237 62 87 90 F +33 (0) 237 62 88 01 email: [email protected] www.cxr.com Smart Solutions for Smart Networks VDD2-H-4TPOE-S ACDC-I-48V-120W-DM Hardened VDSL Modem 2 wire, powerfeed source of remote modem VDD-H-TPOE-S, 100Mbps at 300m , 20Mbps at 1,2km, 1 port 10/100BT, power 47 to 5Vdb dual terminal block and self blocking jack, -40 to + 75° C, DIN rail aluminium case. Hardened VDSL 2 wire Modem POE Pse 802.at 30W, powerfeed through line per VDD-H-TPW-M or w power 47 to 57 Vdb dual terminal block and self blocking jack, 100Mbps at 300m , 20Mbps at 1,2km, 1 port 10/100BT, -40 to + 75°C, DIN rail aluminium case. AC to DC48V 2,5A 120W adaptater for switch and media converter, tpure ACDC-H-48V-240W-DM AC to DC48V 5A 240W adaptater for switch and media converter, tpure 25 to 65°C and 75% at 70°C, terminal block, DIN-Rail metal box CXR Anderson Jacobson reserves the right à modify the specifications without notice. This document is not a contractual document.