8m4503651 4.5l ec alpha rwc single point drain

LIFTING EYE
LIFTING EYE
SINGLE POINT
WATER DRAIN
COVER
500
[19.7]
389
[15.3]
389
[15.3]
702
[27.6]
373
[14.7]
372
[14.6]
35.5
[1.40]
51-57
[2.00-2.25]
ALTERNATOR
REMOTE OIL
FILTER
FUEL FILTER CAP
FUEL INLET
CONNECTION
3/8-18 NPTF FEMALE FITTING
3/8-18 NPTF MALE PLUG
548.7
[21.60]
POWER STEERING PUMP
POWER STEERING
CYLINDER
FUEL FILTER
222.3
[8.75]
242
[9.5]
FUEL INLET CONNECTION
13°
111.3
[4.38]
HEATER HOSE ROUTE
DRAIN PLUG
188
[7.4]
395
[15.55]
571.5
[22.50]
702.7
[27.67]
285.7
[11.25]
NOTES:
(1) REFER TO THE APPLICATION MANUAL FOR COMPLETE PRODUCT INSTALLATION REQUIREMENTS.
(2) DIMENSIONS REQUIRE A MINIMUM OF 1/2 in. (13 mm) CLEARANCE FOR MOTOR MOUNT DEFLECTION.
(3) INNER AND OUTER SURFACES OF TRANSOM MUST BE PARALLEL WITHIN 1/8 in. (3 mm) IN AREA COVERED BY TRANSOM
PLATES AND REMAIN WITHIN TRANSOM THICKNESS LIMITS.
(4) REFER TO "TRANSOM CUTOUT" IN THE INSTALLATION MANUAL TO FIND THE CRANKSHAFT CENTERLINE VS. BOAT BOTTOM.
8M4503651
4.5L EC ALPHA RWC
SINGLE POINT DRAIN
REVISION
B
UNITS
SCALE
mm
(in)
1:12
25.4 mm = 305 mm
1" = 1'
SHEETS
1
OF2
C
CIRCUIT BREAKER
FUSES
DRIVE LUBE CAP
OIL FILL CAP
OIL FILTER
POWER STEERING
FLUID CAP
OIL LEVEL
DIPSTICK
HEATER KIT CONNECTION
IN
ENGINE CONTROL
MODULE ECM
NON DTS: MECHANICAL
THROTTLE AND SHIFT
CABLE CONNECTIONS
HEATER KIT CONNECTION
RETURN
AIR INTAKE
FLAME ARRESTER
DRIVE LUBE CONNECTION
OIL LEVEL
DIPSTICK
TRANSOM
HARNESS
RECEPTACLE
TRANSOM RAW WATER QUICK CONNECT
LIFTING EYE
NON DTS:
MECHANICAL
THROTTLE AND
SHIFT CABLE
CONNECTIONS
(+) BATTERY TERMINAL CONNECTION
14 PIN
ELECTRICAL
HARNESS
RECEPTACLE
567
[22.3]
WITH 2'' RISER
WEATHER CAP
RECEPTACLES
517
[20.3]
669
[26.4]
WITH 6'' RISER
''KIT ONLY''
618
[24.3]
WITH 4'' RISER
89
[3.5]
222
[8.7]
MOUNTS ADJUST 13
[1/2] UP OR DOWN
(-) BATTERY TERMINAL
CONNECTION
40
[1.6]
139.7
[5.50]
TO
MOUNT HOLES
(3/8'' [10] NOM. DIA BOLT HOLES)
NOTES:
(1) REFER TO THE APPLICATION MANUAL FOR COMPLETE PRODUCT INSTALLATION REQUIREMENTS.
(2) DIMENSIONS REQUIRE A MINIMUM OF 1/2 in. (13 mm) CLEARANCE FOR MOTOR MOUNT DEFLECTION.
(3) INNER AND OUTER SURFACES OF TRANSOM MUST BE PARALLEL WITHIN 1/8 in. (3 mm) IN AREA COVERED BY TRANSOM
PLATES AND REMAIN WITHIN TRANSOM THICKNESS LIMITS.
(4) REFER TO "TRANSOM CUTOUT" IN THE INSTALLATION MANUAL TO FIND THE CRANKSHAFT CENTERLINE VS. BOAT BOTTOM.
8M4503651
4.5L EC ALPHA RWC
SINGLE POINT DRAIN
REVISION
B
UNITS
SCALE
mm
(in)
1:12
25.4 mm = 305 mm
1" = 1'
SHEETS
2
OF2
C

Download Report