Accelerators for Network Analysis NT20E-NEBS 2-PORT 10G PCIe NEBS COMPLIANT PACKET CAPTURE FEATURE HIGHLIGHTS The NT20E-NEBS accelerator is designed for Telecom packet capture applications, which require compliance with NEBS requirements. •• •• •• •• NT20E-NEBS provides the same high performance and feature set as the NT20E accelerator, but is based on enhanced hardware capable of operating under extreme conditions with high reliability. •• •• •• •• •• NT20E-NEBS accelerators can also be used in in-line mode. •• •• •• •• FEATURES •• NEBS-3 Compliant HW Time Stamp and Time Sync •• Frame Processing •• IP Fragment Handling •• Flow Identification •• Frame and Flow Filtering •• Intelligent Multi-CPU Distribution •• Advanced Statistics •• Monitoring Sensors •• Linux, FreeBSD and Windows •• •• NEBS level-3 compliance 2 x 10 Gbps XFP connections Full-line-rate packet capture for all frame sizes 1.2 sec. of onboard data burst buffering Typical CPU load: 5% 10 ns time-stamping GPS, CDMA and IEEE 1588 time synchronization Intelligent features for application acceleration RMON1 statistics Temperature and voltage sensors Support for IPv4, IPv6, UDP, TCP, GRE, SCTP, GTP Support for ISL, VLAN and MPLS encapsulation On-the-fly fully reconfigurable setup Easy-to-integrate API libpcap and WinPcap support •• NAPATECH-SUPPORTED APPLICATIONS Napatech NEBS accelerators enable OEM vendors to build high-performance network appliances based on standard servers that meet the stringent requirements of telecom and government applications. Examples of applications include: •• •• •• •• •• Revenue and services optimization Quality of experience optimization Telecom network management Network behavior simulation Financial latency measurement 2 x 10 Gbps PCIe DN-0839 Rev. 2 Disclaimer: This document is intended for informational purposes only. Any information herein is believed to be reliable. However, Napatech assumes no responsibility for the accuracy of the information. Napatech reserves the right to change the document and the products described without notice. Napatech and the authors disclaim any and all liabilities. Napatech is a trademark used under license by Napatech A/S. All other logos, trademarks and service marks are the property of the respective third parties. Copyright © Napatech A/S 2014. All rights reserved. SPECIFICATIONS ACCELERATOR HARDWARE GENERAL FEATURES •• •• •• •• •• •• •• •• •• Full line-rate processing for all frames from 64 bytes to 10,000 bytes IEEE standard: IEEE 802.3 10 Gbps Ethernet support Physical interface: 2 XFP ports Supported XFP modules: Multi-mode SR (850 nm), singlemode LR (1310 nm) or single-mode ER (1550 nm) Data rate: 2 x 10 Gbps PCIe performance: 12.5 Gbps full duplex full-duplex Typical CPU load: 5% Time formats: PCAP-ns/-µs, native, NDIS 10 ns/100 ns, UNIX 10 ns •• •• •• ENVIRONMENT •• •• •• •• HOST INTERFACE •• •• •• Data transfer modes: •• Bus master DMA •• Memory write or memory read transactions Bus type: 8-lane 2.5 GT/s PCIe Gen1 Flash: Supports two boot images Memory options: Standard SO-DIMM 200-pin 2 GB or 4 GB DDR2 RAM modules Physical dimensions: ½-length full-height PCIe Temperature and power sensors •• •• Power consumption: 36 Watts including XFP SR or RJ45 modules Operating temperature (up to 1,800 m): –5 °C to 55 °C (23 °F to 131 °F) measured around the accelerator Altitude –60 m to 1,800 m (–197 ft to 5,906 ft) @ 55 °C Altitude –60 m to 4,000 m (–197 ft to 13,123 ft) @ 45 °C Operating humidity: 5% to 85% MTBF: 222,902 hours according to RIAC-HDBK-217Plus The accelerator requires a laminar air flow along the board with a minimum velocity of 0.5 m/s (100 LFM) for operation up to 40 °C and 2.5 m/s (500 LFM) for operation up to 55 °C REGULATORY APPROVALS AND COMPLIANCES •• NEBS-3, CE, CB, RoHS, REACH, cURus (UL), FCC, CSA, VCCI, C-TICK ACCELERATOR SOFTWARE •• •• •• •• Supported operating systems •• Linux •• FreeBSD •• Windows API supporting user level applications libpcap and WinPCAP support SDK tools included in source code for debugging and prototyping and as examples of how the accelerators are used COMPANY PROFILE Napatech is the world leader in accelerating network management and security applications. As data volume and complexity grow, the performance of these applications needs to stay ahead of the speed of networks in order to do their jobs. We make this possible, for even the most demanding financial, telecom, corporate and government networks. Now and in the future, we enable our customers’ applications to run faster than the networks they need to manage and protect. Napatech. FASTER THAN THE FUTURE STATISTICS •• •• •• RMON1 counters plus jumbo frame counters per port Frame and byte counters per color (filter) and per host buffer Counter sets always delivered as a consistent timestamped snapshot EUROPE, MIDDLE EAST AND AFRICA Napatech A/S Copenhagen, Denmark Tel. +45 4596 1500 [email protected] www.napatech.com NORTH AMERICA Napatech Inc. Boston, Massachusetts Mountain View, California Washington D.C. Tel. +1 888 318 8288 [email protected] www.napatech.com SOUTH AMERICA Napatech São Paulo, Brazil Tel. +55 11 2127 0782 [email protected] www.napatech.com APAC Napatech Japan K.K. Tokyo, Japan Tel. +81 3 5326 3374 Napatech Korea Seoul, South Korea Tel. +82 2 6001 3545 [email protected] www.napatech.com
© Copyright 2024 ExpyDoc
![Acceleranti - eng [modalità compatibilità]](http://s3.expydoc.com/store/data/006987772_1-16b8bc61ffc54bcb7a8976023add5c4a-250x500.png)
