FRONT FILE NEXT FILE UP Type N I S S E I ポリプロピレン・フィルム・コンデンサ APH POLYPROPYLENE FILM CAPACITOR 特徴/Features ●小型軽量です。 ●電極箔はみ出し構造でリード線は電極に溶接されております。 ●外装はエポキシ樹脂でディップされ、耐湿性、耐溶剤性に優れています。 ●誘電正接が小さく、温度特性が極めてフラットな製品です。 ●高忠実度のオーディオ回路、テレビの高電圧回路、その他の高周波回路 に最適です。 ●容量の温度特性は、負特性を示します。 ★Small size and light weight. ★Extended foil construction and leads are completely welded to electrodes. ★Protected against moisture and solvent through our original epoxy resin vacuum impregnation. ★Tangent of loss angle is normally low and its temperature characteristics is flat. ★Recommended for high fidelity circuit in audio, high voltage circuit in TV and other high frequency circuits. ★Characteristics of capacitance is "negative". 規格/Spacications 定 格 電 Voltage 圧 絶 縁 抵 抗 Insulation resistance -25∼+70℃(+85℃)※ 100V、200V、400V、630Vd.c 静 電 容 量 範 囲 Capacitance 100 V 0.00033∼0.47μF 200 V 0.0047∼0.22μF 400 V 0.0027∼0.22μF 630 V 0.001∼0.10μF 静電容量許容差 Cap. tolerance ±2%(G)、±5%(J)、±10%(K) 誘 電 正 接 Tangent of loss angle ( 以上 以上 C≦0.33μF 50,000 MΩ以上 or more C>0.33μF 30,000MΩ以上 or more 高 温 負 荷 Endurance 70℃ WV ×140%, 1000hr印加 以内 ΔC/C ±2%以内 tanδ 0.0011 以下 以下 within or less 以上 IR 15,000MΩ以上 or more 耐 湿 負 荷 Damp heat 40℃、 90∼95%RH WV 500hr印加 以内 ΔC/C ±3%以内 tanδ 0.0012 以下 以下 or less within 以上 IR 15,000 MΩ以上 or more ( 使 用 温 度 範 囲 Temp range 定格 100 VはE-24、 それ以外はE-12 0.001以下 (at 1 KHz) or less ※( )温度は電圧軽減による使用可能範囲です。 ※( )Marked temperature shows operatable range when voltage derated. 寸法/Dimensions(mm) Type WV 寸 APH (E−12) Cap(μF) 法 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 W H 9.5 8.5 APH 100V.d.c. T P 5.5 6.0 F φd 5.0 0.5 W H 12.0 11.0 14.0 12.0 12.5 11.5 9.0 11.0 14.0 7.5 9.5 10.0 11.0 11.5 11.0 11.5 12.0 12.5 16.0 18.0 18.5 19.0 13.5 14.5 15.0 15.5 16.5 17.0 18.0 24.0 24.5 18.5 19.5 20.5 6.0 6.5 6.0 10.0 12.0 12.5 13.0 13.5 5.0/7.5 18.5 6.5 7.0 6.5 7.5 8.0 7.5 8.0 8.5 9.5 11.5 9.0 10.0 11.0 12.0 12.5 0.6 5.0/7.5/10.0 19.0 15.0 14.0 14.5 15.0 16.0 17.0 18.0 24.0 5.0/7.5/15.0 25.0 20.0 ご使用にあたっては、使用上の注意事項(8-14頁)を、ご確認の上技術 仕様書などをお求め願い、仕様書の範囲内でのご使用をお願いします。 15.0 20.0 19.0 20.0 21.5 APH 200V.d.c. T P 6.0 6.5 7.0 7.5 6.5 7.0 10.0 7.5 8.0 8.5 7.5 8.0 8.5 9.0 9.5 10.5 9.5 10.0 11.0 12.0 F φd 5.0/7.5/10.0 0.6 15.0 5.0/7.5/15.0 20.0 15.0 20.0 0.8 0.8 When using our capacitors, please consider the application notes on pages 8-14 and contact Nissei for any additional technical specifications relating to the limits of our performance characteristics. − 30 − Type N I S S E I ポリプロピレン・フィルム・コンデンサ APH POLYPROPYLENE FILM CAPACITOR ストレートリード Straight lead type Max T P ±1.5 20Min Max H 2.0Max 形 状 Style Max W Cap範囲 Cap range シングルフォーミング Single formed lead type 5.0Max 5.0Max 5.0Max 5.0±0.5 5.0±0.5 5.0±0.5 F ±0.8 φd±0.05 F ±0.8 F ±0.8 100 V.dc 331∼474 331∼223, 243∼473 623∼823, 134∼224 304∼474 243∼224, 513∼224 913∼124, 244∼274 200 V.dc 472∼224 472∼822, 472∼273 103∼273, 563∼104 154∼224 103∼104, 333∼104 124, 333∼473 472∼822 400 V.dc 272∼224 272∼562, 272∼153 682∼153, 333∼473 104∼154 682∼393, 183∼473 563∼823, 183∼273 184∼224 272∼562 630 V.dc 102∼104 102∼222, 102∼822 153∼223, 563∼683 272∼822 272∼223, 103∼223 103∼123, 273∼473 823∼104 102∼222 テーピング仕様のリードピッチ寸法(F) はP5※テーピング寸法表をご参照下さい For a pitch space (F) of the taping specification, refer to "TAPING DIMENSION"on p.5. 寸法/Dimensions(mm) Type WV 寸 APH (E−12) Cap(μF) 法 102 0.0010 122 0.0012 152 0.0015 182 0.0018 222 0.0022 272 0.0027 332 0.0033 392 0.0039 472 0.0047 562 0.0056 682 0.0068 822 0.0082 103 0.010 123 0.012 153 0.015 183 0.018 223 0.022 273 0.027 333 0.033 393 0.039 473 0.047 563 0.056 683 0.068 823 0.082 104 0.10 124 0.12 154 0.15 184 0.18 224 0.22 W 12.0 14.5 15.0 16.0 19.0 19.5 H 10.5 11.0 12.0 12.5 13.0 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 17.0 24.0 25.0 29.0 18.0 19.0 20.0 21.0 22.0 22.5 24.0 APH 400V.d.c. T P 6.0 6.5 7.0 7.5 6.5 7.0 7.5 8.0 8.5 7.5 8.0 8.5 7.5 F φd 5.0/7.5/10.0 0.6 W 12.0 14.0 15.0 10.0 15.5 18.5 15.0 19.0 24.0 5.0/7.5/15.0 9.0 9.5 8.5 9.0 9.5 10.5 11.5 12.5 12.0 13.0 20.0 7.5/15.0 15.0 0.8 25.0 29.0 20.0 H 10.0 10.5 11.0 11.5 12.0 11.0 11.5 12.5 13.0 13.5 14.0 14.5 15.5 16.0 16.5 17.5 17.0 18.0 19.0 20.0 21.5 22.5 23.0 24.0 APH 630V.d.c. T P 6.5 7.5 F 5.0/7.5/10.0 φd 0.6 7.0 10.0 7.5 8.0 8.5 9.0 9.5 8.0 8.5 9.0 10.0 8.5 9.5 10.5 11.5 12.5 13.5 12.5 13.0 15.0 5.0/7.5/15.0 20.0 15.0 0.8 20.0 25.0 25.0 使用上の注意/Caution ●APHは、構造上およびフィルム性質上、熱に敏感です。はんだ付け時の 取扱いについては、10頁の“はんだ付け作業について”をご参照下さい。 ご使用にあたっては、使用上の注意事項(8-14頁)を、ご確認の上技術 仕様書などをお求め願い、仕様書の範囲内でのご使用をお願いします。 APH is sensitive for heating due to its construction and film material. Refer to instructions for soldering handling of page 10. When using our capacitors, please consider the application notes on pages 8-14 and contact Nissei for any additional technical specifications relating to the limits of our performance characteristics. − 31 − NISSEI PART NUMBER CODE SYSTEM (1) (2) Type (3) Lead Internal con fig use uration (4) Rated voltage (5) CapacitanceCapacitance tolerance value Model Code (Standard "0000") (6) Lead Dimensions Packing Mode code *2 (2) Lead configuration code Code *1 C Lead configuration Typical Code Samples Straight lead Single formed (leads) 5.0 Code 0200 22.5 0225 25.0 0250 27.5 0275 0125 0150 Style Code 1 0200 *4 2 D200 3 D210 Formed leads type Lead taping for automatic insertion machine (Straight leads) 0175 20.0 Lead spacing (F) after forming indicated as multiplied by 10.Always in bulk Type S 17.5 0100 15.0 Lead taping for automatic insertion machine (Formed leads) Code 0075 12.5 Double formed (leads) Lead length multiplied by 10.Always in bulk F (mm) Lead spacing 0050 *3 10.0 V No lead processing and always in bulk (0000) 0050 Cut shorter (cut leads) 7.5 D Description 0000 F (mm) Lead spacing F (6) Lead dimension /Packing mode 4 D220 5 0200 6 0200 Single / Double-formed leads taped and ammo-packed. See p.5 to 6. 0200 (AMZ50V& Straight leads taped and ammo-packed. See p.5 to 6. AMC:C220) Straight leads type *1 The blank square signifies a straight lead type. *2 some types could bear different lead dimension codes, to be confirmed each case. As to reel packing, contact Nissei. *3 a code Cap471 to 393 in Model Code "0000"of AMC type shall be "1050". *4 a code Cap471 to 393 in Model Code "0000"of AMC type shall be "A210". (3) Rated Voltage (V.d.c,V.a.c) Voltage Code 25 35 50 63 100 125 200 250 275 315 400 450 630 800 1000 1250 1600 0025 0035 0050 0063 0100 0125 0200 0250 0275 0315 0400 0450 0450 0800 1000 1250 1600 (4) Capacitance Tolerance Code F G H J K M Tolerance (%) +/- 1 +/- 2 +/- 3 +/- 5 +/- 10 +/- 20 (5) Capacitance Code Capacitance (pF) expressed in 3-digit code. The first two digits: Significant figures of capacitance value. The third digit: The number of zeros to follow the significant figures. Coding Sample 1) Coding of: AMZ 50V, 0.10 microF, +/-5%, SINGLE formed, taped and ammo-packed AMZ V (1) (2) Internal use 0050 (3) J 104 (4) (5) 0000 0200 Model Code (6) (Standard "0000") 2) Coding of MMC 250V 1.0 μF +/-10%, single formed with 15.0mm leads, in bulk MMC F (1) (2) Internal use 0250 K 105 (3) (4) (5) 0000 0150 Model Code (6) (Standard "0000") 3) Coding have: MMT 50V 0.1 microF +/-5%, straight lead (in bulk) MMT (1) 0050 (2) Internal use (3) J 104 (4) (5) 0000 0050 Model Code (6) (Standard "0000") When using our capacitors, please consider the application notes on pages 8-15 and contact Nissei for any additional technical specifications relating to the limits of our performance characteristics.
© Copyright 2025 ExpyDoc