Bedienungsanleitung User Manual

Bedienungsanleitung
Seite: 1-5
User Manual
Page: 6 - 11
PEGASUS PRO 1.0 RGB
LIG0009199-000
Lieber Kunde,
vielen Dank das Sie sich für ein Produkt von LightmaXX entschieden haben. In der
folgenden Anleitung erhalten Sie wichtige Informationen über dieses Produkt sowie
deren Eigenschaften und Funktionen.
1
!ACHTUNG!
Laserschutzbestimmungen:
Durch die starke Bündelung des Laserstrahls ist die gesamte Lichtenergie auf eine
geringe Fläche konzentriert. Wird das menschliche Auge von diesem Strahl getroffen,
kann dies Schädigungen hervorrufen. Insbesondere besteht die Gefahr von
Augenverletzungen beim Blick in den direkten Strahl. Ist der Strahl abgelenkt, was bei
den kompakten Showlasersystemen durch die Scanning Einheit
fast immer der Fall ist, ist die Wirkung und somit die Gefahr des Strahls um ein
Vielfaches geringer.
Entsprechend der möglichen Gefährdung werden Laser bzw. Geräte, die einen Laser
enthalten, gemäß Unfallverhütungsvorschrift Laserstrahlung [BGV B2] in Klassen
eingeteilt. 99% der aktuell auf dem Markt erhältlichen kompakten Showlaser und
auch alle von uns angebotenen Laser gehören zur Schutzklasse 3a und 3b. Diese
Geräte sind somit genehmigungspflichtig. Zum sicheren Betrieb bei öffentlichen
Veranstaltungen ist ein Laserschutzbeauftragter [Strahlenschutz gemäß VBG 93 §6
(BGV-B2)] zu bestellen. Bei Installationen in öffentlichen Gebäuden (Discotheken,
Mehrzweckhallen, Gaststätten etc.) sind die Systeme vom örtlich zuständigen TÜV
oder der Berufsgenossenschaft abzunehmen. Die in Deutschland gültigen
Bestimmungen zum Betrieb einer Showlaser Anlage müssen beachtet werden.
Informieren Sie sich hierzu bei Ihrer örtlichen Berufsgenossenschaft und der
zuständigen TÜV Behörde.
Technische Daten:
Laserleistung:
400mW blau / 150mW grün / 500mW rot
Scanner System: 30k High Speed Galvo Motoren
Funktions Modis: Sound to Light, Automatik Modus, Master/Slave, DMX 512, ILDA
Anschlusswerte: 240 V, 50 Hz / 40 Watt
Gewicht:
6,0 Kg
2
Rückansicht:
Betriebseinstellungen:
LCD FUNCTION SETTING
ENTER
UP
UP
DMX-512
Auto
RETURN
DOWN
Mit den Tasten UP und DOWN wechseln Sie zwischen den Menü Unterpunkten
Mit der Taste ENTER bestätigen Sie Ihre Einstellung
Mit der Taste RETURN gelangen Sie wieder einen Menüschritt zurück
3
Menüführung:
1. Menü Ebene
2. Menü Ebene
3. Menü Ebene
4. Menü Ebene
Running
DMX512
A001 (DMX address)
Running
AUTO
(auto
running mode)
Effect 1 (Full show)
Effect 2 (only beam)
Effect 3 (only cartoon)
Running
Music
(sound
activate mode)
Effect 1 (Full show)
Effect 2 (only beam)
Effect 3 (only animation)
Address
Choose DMX address
OFF
Light
ON
(LCD backlight setting)
ON 5S (ON for 5 seconds)
ON 10S (ON for 10 seconds)
Press UP and down to choose
Cartoon (Running speed)
running speed from 1~99,
99
is the fastest
Setting
Master (set master unit)
OFF
ON
(press up or down to
Size
LASER
choose the size of
graphics)
(size and
1. Single Color
color setting)
Color
2. RGY
3. RGB
4. RGP
Default
default setting)
(Restore
Yes
No
4
DMX Protokoll:
LASER OFF
Auto Activate
CH1
Sound
Activate
CH2
CH3
Pattern select
Rotation
CH4
X axis rolling
CH5
Y axis rolling
CH6
X axis moving
CH7
Y axis moving
Pattern size
CH8
CH9
Zooming
Drawing
Scanning
CH10
speed
Display dot
CH11
Color setting
0~41
LASER OFF
42~83
DMX mode, CH2~CH12 valid
84~125
Build-in cartoon graphics auto running mode
126~167
Build-in beam graphics auto running mode
168~209
Build-in beam graphics auto running mode
210~251
Build-in cartoon graphics auto running mode
252~255
DMX mode, CH2~CH12 valid
0~255
Selecting built-in patterns
0~127
Manual rotation
128~191
Auto counter-clockwise rotation (from slow to fast)
192~255
Auto clockwise rotation (from slow to fast)
0~127
Manual rolling
128~255
Auto rolling (from slow to fast)
0~127
Manual rolling
128~255
Auto rolling (from slow to fast)
0~127
Manual choose moving position
128~255
Auto moving (from slow to fast)
0~127
Manual choose moving position
128~255
Auto moving (from slow to fast)
0~63
64~127
Auto zooming (-) from slow to fast
128~191
Auto zooming (+) from slow to fast
192~255
Manual zooming (+/-) from slow to fast
0~255
Auto drawing from slow to fast
0~127
Choose sanning speed from slow to fast
128~255
Choose the length of dot
0~24
Normal color
25~199
Choose every single color
200~224
Every single color changing one by one
225~255
CH12
Color change
speed
Choose pattern size, 0 is normal size, 1 is the smallest, 63 is the biggest
0~255
All the colors together changing alternatively in one pattern
Adjust color changing speed from slow to fast
5
Service and repair
The Laser Show equipment has no major serviceable parts. Repair of electronic- components (transistors,
IC´s) or changing other parts are not allowed by untrained persons. If there is a problem with the Laser
Show equipment, your local service engineer will help you with repair or replacement. We recommend
shipping the Laser Show equipment to the manufacturer for reparation.
Attachments:
1. Laser Light:
2. Power Cable:
3. User Guide:
1PCS
1PCS
1PCS
WARNINGS

Visible and invisible laser-light, direct beam can damage the human eye and the eyes of animals. Do not look at
any Laser light directly.

Do not touch the laser aperture with the hand. When cleaning the laser aperture, please use a soft cloth with
alcohol or camera lens paper.

Do not take apart or modify the equipment. Fire or electrical shock may result.

In the unlikely event that you hear unusual noise, see smoke, feel excessive heat or smell anything unusual,
immediately unplug the power source and contact your retailer. Continued use may result in fires or electrical
shock.

Do not use flammable sprays near this equipment. Also do not spill water, liquids, or flammable liquids on the
equipment. If fluids enter this equipment and contact the electrical parts, fires or electrical shock may result. If
anything enters the equipment, immediately unplug the power supply and contact your retailer.
Installation
1. Carefully inspect your Laser Show equipment after you unpack it. If any damage is evident, such as dents or
scratches on the covers or broken knobs, etc., immediately notify your carrier and your local sales distributor.
2. Hang up the equipment in a safe place. Ensure there are no barriers in front of the laser aperture.
Features of the product:
1. Laser power: 400mW blue laser @ 450nm, 150mW green laser @ 532nm
500mW red laser @ 650nm, mixed 1W RGB.
2. Scanner system: 30K high speed optical scanner
3. Working Modes: Sound Active, Auto run, DMX512 (12 CH), Master/slave mode, ILDA mode.
4. Interface: 3 pins XLR jack for DMX or Maser-Slave linking; DB25 ILDA interface for PC control
5. Input power: AC 110V~240V, 50/60Hz. Rated power: 40W.
6. Packing Size: L*W*H=390*290*190mm; Weight: 6KG
6
Front and Rear panel view:
3
1
2
4
5
6
1. Laser Aperture 2. Sound active microphone 3. Running LED (indicates the unit is running OK)
4. Power LED indicator
7
5. Mic LED
8
7. ON/OFF switch 8. Power Jack
11. Key lock
6. DMX signal LED
9
11
1
10
1
12
1
13
1
9. DMX or linking jack 10. Eyebolt for safe cable
12. LCD function setting screen
13. Sound sensitivity knob 14. DB25 ILDA interface
7
14
1
LCD FUNCTION SETTING
ENTER
DMX-512
UP
UP
Auto
RETURN
DOWN
Press “UP” or “DOWN” to choose functions in the same menu.
Press “ENTER” button to enter next menu.
Press “RETURN” button to return previous menu.
When you turn on the laser for the first time, it will take some seconds to auto load the built-in show.
The default setting is AUTO EFFECT 1.
First Menu
Second Menu
Third Menu
Running
DMX512
A001 (DMX address)
Running
AUTO
(auto
running mode)
Effect 1 (Full show)
Effect 2 (only beam)
Effect 3 (only cartoon)
Running
Music
(sound
activate mode)
Effect 1 (Full show)
Effect 2 (only beam)
Effect 3 (only animation)
Address
Choose DMX address
Light (LCD backlight setting)
OFF
Setting
8
Fourth Menu
ON
ON 5S (ON for 5 seconds)
ON 10S (ON for 10 seconds)
Press UP and down to choose
Cartoon (Running speed)
running speed from 1~99,
99
is the fastest
OFF
Master (set master unit)
ON
(press up or down to
Size
choose the size of
graphics)
LASER (size and color
setting)
5. Single Color
Color
6. RGY
7. RGB
8. RGP
Default
(Restore
default setting)
Yes
No
Universal DMX Operation (DMX mode)
This mode allows you to use universal DMX-512 console to operate.
1. Install the units in a suitable position.
2. Use standard XLR cable to connect your units together via the XLR connector on the rear of the units. For longer
cable we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches.
4. Turn on all units. Use DMX console to control your units.
DMX Signal
9
Instruction for DMX channels
LASER OFF
Auto Activate
CH1
0~41
LASER OFF
42~83
DMX mode, CH2~CH12 valid
84~125
Build-in cartoon graphics auto running mode
126~167
Build-in beam graphics auto running mode
168~209
Build-in beam graphics auto running mode
210~251
Build-in cartoon graphics auto running mode
252~255
DMX mode, CH2~CH12 valid
0~255
Selecting built-in patterns
0~127
Manual rotation
128~191
Auto counter-clockwise rotation (from slow to fast)
192~255
Auto clockwise rotation (from slow to fast)
0~127
Manual rolling
128~255
Auto rolling (from slow to fast)
0~127
Manual rolling
128~255
Auto rolling (from slow to fast)
0~127
Manual choose moving position
128~255
Auto moving (from slow to fast)
0~127
Manual choose moving position
128~255
Auto moving (from slow to fast)
Sound
Activate
CH2
CH3
CH4
CH5
CH6
CH7
Pattern select
Rotation
X axis rolling
Y axis rolling
X axis moving
Y axis moving
Pattern size
CH8
0~63
Choose pattern size, 0 is normal size, 1 is the smallest, 63 is the biggest
64~127
Auto zooming (-) from slow to fast
128~191
Auto zooming (+) from slow to fast
Zooming
10
CH9
192~255
Manual zooming (+/-) from slow to fast
0~255
Auto drawing from slow to fast
0~127
Choose sanning speed from slow to fast
128~255
Choose the length of dot
0~24
Normal color
25~199
Choose every single color
200~224
Every single color changing one by one
Drawing
Scanning
CH10
speed
Display dot
CH11
Color setting
225~255
CH12
Color change
speed
All the colors together changing alternatively in one pattern
0~255
Adjust color changing speed from slow to fast
TROUBLE SHOOTING
1. If the power indicator is off and the laser doesn't work, please check the power supply and the input.
2. In Stand-Alone operation, if the power supply indicator is ON and sound active indicator is OFF, but the
laser doesn't work.
A. Because sound is too small and cannot activate laser running, please increase the music volume or
increase audio sensitivity on rear panel.
B. Please check if unit has been set up in slave mode, or DMX mode.
3. In Master-Slave operation, slave units don't function, please check as below.
A. Make sure there's only one master in the chain, and the others are set in slave mode.
B. Make sure to control the units with DMX controller.
C. Make sure to use a good quality power cable and XLR connector.
4. In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal indicator is
flashing, please make sure the DMX console and unit have the same channel.
5. If the output beam direction above is unusual, please restart the unit.
6. If the unit is fail, please turn off the unit, and then turn on again after 5 minutes.
After trying the above solution you still cannot sort out the problem, please contact your dealer or our company for
service.
www.musicstore.com
11

Download Report