Configurator PRIMERGY CX400 S2

PRIMERGY CX400 S2 / CX2y0 S2
System configurator and order-information guide
January 2015
Contents
Instructions
Configuration diagram
Configurator
0
I
II
III
IV
V
VI
VII
VIII
IX
X-I
X-II
XI
XII
System software
CX400 S2 Basic unit
CX250 S2/ CX270 S2Basic unit
Processor
Graphics / GPGPU
Memory
Drive bay for basic unit
Hard disk drives
Onboard SW RAID 0/1, additional raid option
External SAS Disk Array, SAS backup drives or SCSI peripheral devices
Communication/Network for CX250 S2
Communication/Network for CX270 S2
System Management Products (RemoteView)
Miscellaneous
Change report
PRIMERGY Server
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III
Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX
Memory XXX MB
S26361-XXX-XXX
Memory XXX MB
max. X times per system
max. X times per system
X times
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet)
Fujitsu Technology Solutions x86 PRIMERGY Serve
2 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Configuration diagram PRIMERGY CX400 S2
System unit ( I )
with up to 12x 3.5" or up to 24x 2.5" Hard disk drives (or SSD)
Below drawing shows HDD tray numbering. For HDD installation order, please refer operating manual.
CX400 S2 3,5" HDD cage standard (S26361-K1476-V135)
CX400 S2 2,5" HDD cage standard (S26361-K1476-V125)
Key:
Included in basic unit
Option
Note: each CX400 has to be populated with 4x CX250 S2 or 2x CX270 S2
Each nodes are hot plugable, and all node are same type, and different configuration for each node is allowed.
Tray 3
PSU 1
Tray 1
Tray 4
PSU 2
Tray 2
CX250 S2 half wide one U server node
CX270 S2 half wide two U server node
Fujitsu Technology Solutions x86 PRIMERGY Serve
3 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Note! Position of CX nodes (MB 1 to 4) are fixed and needs to be configured in same placements.
Fujitsu Technology Solutions x86 PRIMERGY Serve
4 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Configuration diagram PRIMERGY CX250 S2
System unit ( I )
with up to 6 x 2.5" HDDs on CX400 S2 2,5" HDD cage standard
with up to 3 x 3.5" HDDs on CX400 S2 3,5" HDD cage standard
CX400 Chassis parts
Rear side on each node
2 USB
1 VGA
2x LAN & Service LAN
Rear side
Motherboard
Memory CPU1
( Channel A + B + C + D )
Xeon DP
Bank 1 (2 Modules)
Bank 2 (2 Modules)
Bank 3 (2 Modules)
Bank 4 (2 Modules)
1. PSU
Memory CPU2
2. PSU
( Channel E + F + G + H)
Xeon DP
Bank 1 (2 Modules)
Bank 2 (2 Modules)
Bank 3 (2 Modules)
Bank 4 (2 Modules)
Memory (III )
Hotplug power supply
Processor ( II )
Inside
Fan 1 - Fan 4
Non-Hotplug
included in Chassis
LSI SW Raid, Raid 0 / 1 / 10
Onboard for up to 4 SATA HDD
Front
1x PCIe GEN3 via Riser (Riser is part of delivery)
Hard disk drives ( VI )
2.5" SAS/SATA
Slot 1 PCIe-3 x16, 390mm @ CPU2
1x PCIe GEN3 Mezzanine Slot
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
additional Mezz. card
@ CPU1
or unpopulated
Hard disk drives ( VI )
3.5" SATA
3.5" HDD/SSD
or HDD dummy frame
3.5" HDD/SSD
or HDD dummy frame
3.5" HDD/SSD
or HDD dummy frame
Key:
Included in basic unit
Option
The population order for the CPU is: CPU1 first, then CPU2
Fujitsu Technology Solutions x86 PRIMERGY Serve
5 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Configuration diagram PRIMERGY CX270 S2
System unit ( I )
with up to 4x 2.5" HDDs on CX400 S2 2,5" HDD cage standard
with up to 3x 3.5" HDDs on CX400 S2 3,5" HDD cage standard
CX400 Chassis parts
Rear side on each node
2 USB
1 VGA
2x LAN & Service LAN
Rear side
Motherboard
Memory CPU1
( Channel A + B + C + D )
Xeon DP
Bank 1 (2 Modules)
Bank 2 (2 Modules)
Bank 3 (2 Modules)
Bank 4 (2 Modules)
1. PSU
Memory CPU2
2. PSU
( Channel E + F + G + H)
Xeon DP
Bank 1 (2 Modules)
Bank 2 (2 Modules)
Bank 3 (2 Modules)
Bank 4 (2 Modules)
Memory (III )
Hotplug power supply
Processor ( II )
Inside
Fan 1 - Fan 4
Non-Hotplug
included in Chassis
LSI SW Raid, Raid 0 / 1 / 10
Onboard for up to 4 SATA HDD
Front
1x PCIe x16 GEN3 via Riser (Riser is part of delivery)
Hard disk drives ( VI )
2.5" SAS/SATA
Up to 2 blocks with 4 HDD/SSDs
Blocks can be combined
Slot 1 PCIe-3 x8, 390mm @ CPU2
Slot 2 PCIe-3 x8, 390mm @ CPU2
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
2.5" SAS/SATA/SSD
or HDD dummy frame
1x PCIe x16 GEN3 Riser
Slot for GPGPU support @ CPU1
Hard disk drives ( VI )
3.5" SATA
Up to 2 blocks with 3 HDDs
3.5" HDD/SSD
or HDD dummy frame
3.5" HDD/SSD
or HDD dummy frame
3.5" HDD/SSD
or HDD dummy frame
Key:
Included in basic unit
Option
The population order for the CPU is: CPU1 first, then CPU2
Fujitsu Technology Solutions x86 PRIMERGY Serve
6 of 30
PRIMERGY-Software Configurators and Release Lists
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Start PRIMERGY CX250 S2 / CX270 S2
Section
O
SW Configurator 64 bit (EM64T / IA64)
with OEM-Software
for PRIMERGY Server
without OEM-Software
for PRIMERGY Server
OEM- SW is bound to HW and
is not allowed to be ordered
separately.
Exceptions: VMware SW,
Citrix XenServer
For all SW products please refer to the corresponding
software configurator accessible via the Extranet under
"Configuration & Tools, -All configurations, -Software,
URL see below.
VMware-Software
- Virtual Infrastructure for PRIMERGY > except all mono PRIMERGY systems
Microsoft Hyper-V Server and System Center
- Microsoft Hyper-V Server 2008 R2
- Microsoft Hyper-V Server 2012
Microsoft - Windows Server Server Licenses
Linux - Software *) **)
- Windows Server 2008 R2 Datacenter
- Windows Server 2008 R2 Enterprise
- Windows Server 2008 R2 Standard
- Windows Web Server 2008 R2
- Windows Server 2012 Datacenter
-Windows Server 2012 Standard
only
EM64T
- SuSE Linux ES (OEM): LO
- Red Hat EL (OEM): LO
**) Pay attention to release and order information in PRINCE -> Operating System
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
for partners:
http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Fujitsu Technology Solutions x86 PRIMERGY Server
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Start PRIMERGY CX400 S2
I
Section
Basic unit
System unit consisting of:
* 2U Housing with power supply modules, Rack Rails and HDD cages
* Basic units with:
- 4 non-hot plug Fans (limited redundancy)
* SAS Backplane for 12x 3.5" HD or SAS Backplanes for 24x 2.5" HD
* Drives/Bays
- 12 bays 1" for hot plug 3.5" HD (1" high) or 24 bays for hot plug 2.5" HD
- HDD or SSD supported
- HDD configuration per Server node
- empty bays will be covered with dummy frames
* Server nodes
- each CX400 S1 has to be configured either up to 4x CX250 S2 w/o GPGPU support
or up to 2x CX270 S2 w/ GPGPU support
- all other node configurations requires special release process but may be possible
- position of CX server nodes fixed
Software:
* ServerView Suite Software
* Documentation engl. (multilingual on CD)
A
Fujitsu Technology Solutions x86 PRIMERGY Serve
8 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
A
Basic unit with 24x 2,5" HDD bays or
12x 3,5" HDD bays is
to be used for 4 node or 2 node
Datails and integration for HDDs and SSDs
refer configuration options for basic server nodes
Rack version for 19'' racks with
No PSU included in Base Unit
Basic unit is without CPU and Memory
CPU and memory have to be ordered.
Min. configuration is 2x CPU and 2x Memory
Basic unit with
12x 3,5" HDD cage standard
S26361-K1476-V135
Basic unit with
24x 2,5" HDD cage standard
S26361-K1476-V125
System will throttle CPUs and memory
S26361-F4574-E240
S26113-F616-E120
2x 1400W PSU module
2x 1200W PSU module
200-240V
100-240V
92% efficiency
94% efficiency (Platinum)
uses hot plug PSU slot
uses hot plug PSU slot
1x per CX400
1x per CX400
in case of a PSU failure.
So, power consumption will be limited.
Always 2 PSUs required
PSU Criteria for 1,400W PSU and 1,200W PSU from power budget point of view
200-240V
100V
1,400W PSU
No limitation
Not supported
1,200W PSU
No limitation
No LR-DIMM install possible
Please order appropriate power cord additionally:
Powercord for rack, 4m, grey, IEC320 C13->C14 connector
T26139-Y1968-L10
Power Cord USA / Canada, 1.8m, grey
T26139-Y1742-L10
B
Fujitsu Technology Solutions x86 PRIMERGY Serve
9 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
B
PRIMECENTER Rack
Sliding rail
1-hand-mounting
RMK - 1 pair consisting of
- carrier length variable
S26361-F4530-L12
Adapter angle PC/DC-Rack, till 50Kg
toolless mounting possible
necessary for mounting RMKs in
asymmetrical racks
included in base unit
S26361-F4530-E12
Mounting 2U server in
S26361-F4530-E10
Mounting in
asymmetrical racks
symmetrical & 3rd party racks
with 2U support bracket
(no support bracket needed)
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered
"Rack-mounting ex factory"
completely pre-mounted and
This service is to be ordered once
all wired connections are tested.
per installable server/storage
With PCR S2 12U, 24U, 38U and
subsystem, in order to get the
PRC M1 16U, 24U, 42U:
server/storage subsystem
Systems and components
mounted into the racks.
will be delivered installed in the rack
In case of the 46 U PCR S2
With PCR S2 racks 46U:
this service has to be ordered,
Systems and components
to get the mounting kits and the
will be delivered separately
cables installed.
To be ordered only together with
a PRIMECENTER rack
PCR S2 e.g. S26361-K826-V10x
new PCR M1 e.g. S26361-K827-Vxxx
refer PCR S2 or M1 rack configurator
max. 1x per System
PRIMERGY Classic 19" rack is not supported
S26361-F1452-E100
S26361-F1452-E110
REGION KIT EMEA AP
For Shipments to EMEA / Asia and
Pacific regions
1x per system
REGION KIT JP
For Shipments to Japan regions
1x per system
Power cord has to be ordered separately
For shipments to India mandatory!
S26361-F3301-E123
Certification for India
Hint: No country specific powercord configurable with Certification for India
Power cord options (1x per PSU)
T26139-Y1968-E100
Powercord for rack, 4m, grey,
IEC 320 C14 connector
T26139-Y1742-E10
USA, Canada, 1.8m, grey
T26139-Y3850-E10
Option "no powercord", for Countries without
specific cable orderable like e.g. China
2x
C
Fujitsu Technology Solutions x86 PRIMERGY Serve
10 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Start PRIMERGY CX250 S2 / CX270 S2
II
Section
Basic unit
CX250 S2 System unit consisting of:
* 1U half wide server node (tray & motherboard) for pluggin into CX400 chassis
* Basic units with:
- Server tray mechanics
- Motherboard
- 1x Riser PCIe- x16 GEN3 for LP cards
- 1x Mezzanaine cards slot
- 1x UFM placement possible
CX270 S2 System unit consisting of:
* 2U half wide server node (tray & motherboard) for pluggin into CX400 chassis
* Basic units with:
- Server tray mechanics
- Motherboard
- 1x Riser PCIe- x16 GEN3 with 2x PCIe- x8 slots for LP cards
- 1x Riser for GPGPU support at rear of server node
- 1x UFM placement possible
Systemboard D3196-B100 (same for both server nodes CX250 S2 and CX270 S2) with:
* Up to two Xeon 4-12 CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series
* number of PCI slots:
see above
* 16 memory slots for max. 1024GB RAM DDR3 available
- Memory is divided into 8 DIMMs per CPU ( 4 channels with 2 slots per channel )
Possible max. configurations are:
16x 64GB LRDIMM (8 rank modules) = 1024GB
16x 16GB RDIMM (dual rank modules) = 256GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible by 8x memory units
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* AST2300 (integrated Baseborad Management Controller) on-board server management controller with
dedicated 10/100 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port
* Graphics Controller integrated in AST2300 (integrated Baseboard Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins)
* 1x VGA (15 pins)
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces internal:
* 1x USB 2.0 for UFM modul (embeded ESXi)
* SATA interface via Patsburg -A for 4 SATA HD's Raid 0/1/10 (LSI SW Raid)
A
Fujitsu Technology Solutions x86 PRIMERGY Serve
11 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
A
Status 2014-12-30
For non fully ocupied configuration (e.g.
Server node for CX400 S2 2U chassis
1x CX250 S2), it is released as special
PSU is not part of CX400 S2 Base Unit
release only.
Basic unit is without CPU and Memory
And no mixed configuration supported
For an orderable basic unit two CPU and
for CX250 S2 and CX270 S2 in CX400 S2
eight memory = 1 per channel has to be selected
Different HW configuration for each node
in chassis can be possible.
(e.g. different CPU, Mem etc)
CX250 S2 Basic unit without GPGPU support 1U
PRIMERGY CX250 S2
S26361-K1474-V200
CX270 S2 Basic unit with GPGPU support 2U
PRIMERGY CX270 S2
S26361-K1475-V300
CX400 S2 with 4x CX250 S2
S26361-K1474-V200
S26361-K1475-V300
PRIMERGY CX250 S2
PRIMERGY CX270 S2
1U half wide w/o GPGPU support
2U half wide w/ GPGPU support
INTEL Processor
INTEL Processor
based dual socket Server Blade.
based dual socket Server Blade.
max. 4x per system unit
max. 2x per system unit
2x
4x
for CX270 S2
Server#3
Server#1
Server#4
Server#2
CX400 S2 with 2x CX270 S2
for CX250 S2
Server#2
Server#1
S26361-F4574-E100
Dummy nodes
1U half wide dummy
Loose delivery for dummy node
needed to be ordered 1x
S26361-F4574-L100
for each left open server slot
max. 3x per system unit
S26361-F4575-E10
S26361-F4575-E11
Service for CX-Server nodes
Service for CX-Server nodes
installation in the CX400 12x 3.5"
installation in the CX400 24x 2.5"
HDD cage standard
HDD cage standard
max. 4x per system unit
max. 4x per system unit
S26361-F4575-E20
S26361-F4575-E21
CX-Server nodes individually
CX-Server nodes individually
packed/deliverd for CX400 12x 3.5"
packed/deliverd for CX400 24x 2.5"
HDD cage standard
HDD cage standard
max. 1x per CX-Server node
max. 1x per CX-Server node
B
Fujitsu Technology Solutions x86 PRIMERGY Serve
12 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
B
III
Section
Processor
There are 2 processor sockets available.
The CPU socket is always equipped which can be selected via configurator
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Note: Max. DDR3 Bus Speed depends on:
With this order number you will receive two CPUs!
The CX250 is always delivered with two CPUs installed.
Please choose the CPU type (applies to both CPUs)
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB Smart Cache)
1333 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
2x Xeon E5-2603v2 4C/4T 1.80GHz 10MB 6.40GT/s 1333MHz 80W
2x Xeon E5-2609v2 4C/4T 2.50GHz 10MB 6.40GT/s 1333MHz 80W
- max. DDR3 Bus Speed from the CPU and
- max. DDR3 Memory Speed and
- max. memory modules on one memory channel
S26361-F5278-E180
S26361-F5278-E250
Standard Turbo 6/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
2x Xeon E5-2620v2 6C/12T 2.10GHz 15MB 7.20GT/s 1600MHz 80W
2x Xeon E5-2630v2 6C/12T 2.60GHz 15MB 7.20GT/s 1600MHz 80W
2x Xeon E5-2640v2 8C/16T 2.00GHz 20MB 7.20GT/s 1600MHz 95W
S26361-F5279-E210
S26361-F5279-E260
S26361-F5279-E200
Advanced Turbo+ 8/10C CPU`s
- 1x 64-bit Intel Xeon (20MB Smart Cache); Hyper-Threading (HT);
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
2x Xeon E5-2650v2 8C/16T 2.60GHz 20MB 8.00GT/s 1866MHz 95W
2x Xeon E5-2660v2 10C/20T 2.20GHz 25MB 8.00GT/s 1866MHz 95W
2x Xeon E5-2670v2 10C/20T 2.50GHz 25MB 8.00GT/s 1866MHz 115W
2x Xeon E5-2680v2 10C/20T 2.80GHz 25MB 8.00GT/s 1866MHz 115W
2x Xeon E5-2690v2 10C/20T 3.00GHz 25MB 8.00GT/s 1866MHz 130W
S26361-F5280-E260
S26361-F5280-E220
S26361-F5280-E250
S26361-F5280-E280
S26361-F5280-E300
In case of E5-2637/2643 V2, Supported
number of HDDs are limited, and system may
become degraded performance at more than
30 deg-C environment.
Segment Optimized Turbo 4/6/8/12 CPU`s
- 1x 64-bit Intel Xeon (15/25/30MB Smart Cache); Hyper-Threading (HT);
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
2x Xeon E5-2637v2 4C/8T 3.50GHz 15MB 8.00GT/s 1866MHz 130W
2x Xeon E5-2643v2 6C/12T 3.30GHz 25MB 8.00GT/s 1866MHz 130W
2x Xeon E5-2667v2 8C/16T 3.00GHz 25MB 8.00GT/s 1866MHz 130W
2x Xeon E5-2695v2 12C/24T 2.40GHz 30MB 8.00GT/s 1866MHz 115W
2x Xeon E5-2697v2 12C/24T 2.70GHz 30MB 8.00GT/s 1866MHz 130W
S26361-F5281-E350 special release
S26361-F5281-E351 special release
S26361-F5281-E330
S26361-F5281-E240
S26361-F5281-E270
Low Power 4C/6C/8C CPU's
- 1x 64-bit Intel Xeon (15/25MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
2x Xeon E5-2630Lv2 6C/12T 2.40GHz 15MB 7.20GT/s 1600MHz 60W
2x Xeon E5-2650Lv2 10C/20T 1.70GHz 25MB 8.00GT/s 1600MHz 70W
S26361-F5282-E240
S26361-F5282-E170
C
Fujitsu Technology Solutions x86 PRIMERGY Serve
13 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
IV
Section
Graphics / GPGPU / Xeon Phi
Graphics Controller integrated in BMC Aspeed 2300 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
One GPGPU (General Purpose Graphical Processor Unit) or Xeon Phi can be ordered as option.
A mounting kit has to be ordered seperatly and will be installed if ordered ex factory together
with the GPGPU card. New cards requires the suitable bracket and DC cable
The Riser card, air duct and and air tunnel are part of System delivery
1x Mounting kit
+
1x GPGPU or
Xeon Phi
Only for CX270 S2!
S26361-F3736-E270
S26361-F3736-L270
PY K20 / K20X / K40 Mounting Kit
consists of mounting brackest
and fixation material
max. 1x per system
PY K20 / K20X / K40 Mounting Kit
consists of mounting brackest
and fixation material
for loose delivery
S26361-F2222-E23
PY NVIDIA Tesla K20 Computing-Processor
NVIDIA Tesla K20
5 GB Memory
PCIe Gen2-x16
2496 cores
for GPGPU purpose only
max. 1x per system
S26361-F2222-E25
PY NVIDIA Tesla K20X Computing-Processor
NVIDIA Tesla K20X
power cables from PSU are cabled
when ordering GPGPU ex factroy
Riser card for GPGPU is part of delivery
no PCIe bracket attached
power cables from PSU are cabled
when ordering GPGPU ex factroy
Riser card for GPGPU is part of delivery
no PCIe bracket attached
S26361-F2222-L23
S26361-F2222-L25
S26361-F2222-L40
for loose delivery
Riser is part of basic unit CX270
6 GB Memory
PCIe Gen2-x16
2688 cores
for GPGPU purpose only
max. 1x per system
S26361-F2222-E40
PY NVIDIA Tesla K40 Computing-Processor
NVIDIA Tesla K40
12 GB Memory
PCIe Gen3-x16
2880 cores
for GPGPU purpose only
max. 1x per system
power cables from PSU are cabled
when ordering GPGPU ex factroy
Riser card for GPGPU is part of delivery
no PCIe bracket attached
S26361-F3736-E570
PY Xeon Phi Mounting Kit
consists of mounting brackest
and fixation material
max. 1x per system
S26361-F3736-L570
PY Xeon Phi Mounting Kit
consists of mounting brackest
and fixation material
for loose delivery
S26361-F4100-E312
PY Intel Xeon Phi Co-Processor 3120P
Intel Xeon Phi Co-Processor 3120P
6 GB GDDR5 Memory
PCIe Gen2-x16
57 cores and 228 threads
for Co-processing purpose only
max. 1x per system
S26361-F4100-E511
PY Intel Xeon Phi Co-Processor 5110P
Intel Xeon Phi Co-Processor 5110P
8 GB GDDR5 Memory
PCIe Gen2-x16
60 cores and 240 threads
for Co-processing purpose only
max. 1x per system
S26361-F4100-E712
PY Intel Xeon Phi Co-Processor 7120P
Intel Xeon Phi Co-Processor 7120P
16 GB GDDR5 Memory
PCIe Gen2-x16
61 cores and 244 threads
for Co-processing purpose only
max. 1x per system
power cables from PSU are cabled
when ordering Xeon Phi ex factory
Riser card for Xeon Phi is part of delivery
no PCIe bracket attached
power cables from PSU are cabled
when ordering Xeon Phi ex factory
Riser card for Xeon Phi is part of delivery
no PCIe bracket attached
power cables from PSU are cabled
when ordering Xeon Phi ex factory
Riser card for Xeon Phi is part of delivery
no PCIe bracket attached
S26361-F4100-L312
S26361-F4100-L511
S26361-F4100-L712
for loose delivery
Riser is part of basic unit CX270
E
Fujitsu Technology Solutions x86 PRIMERGY Serve
14 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
E
NVIDIA GRID K1 & K2 GPU for pass through / vGPU for VDI / VHD virtual graphic usage
Supported for GPU pass through and vGPU (shared GPU) under Citrix XenServer 6.2 and XenDesktop only. Workload depends on application. Ideal
for virtualized GPU or shared GPU workload like "Power Users" or "Knowlegde Workers", including "Designer" as full power graphic USER. GRID
K2 only supports "Designer" use cases with high graphic load!
All Citrix XenServer guests are supported.
NOT certified for CAD / CAM / CAX type of applications using dedicated GPU. No supports of other virtualized operating systems.
VMware ESXi shared (vSGA) & dedicated (vDGA) virtual graphic support and Microsoft RemoteFX are part of future releases.
S26361-F3736-L271
PY GRID K1/K2 Mounting Kit
for loose delivery
S26361-F3736-E271
PY GRID K1/K2 Mounting Kit
consists of mounting brackest
and fixation material
max. 1x per system
1x
1x
S26361-F2222-L914
S26361-F2222-L924
for loose delivery
Riser is part of basic unit CX270
S26361-F2222-E914
PGRA CP NVIDIA GRID K1
NVIDIA GRID K1
18GB DDR3 Memory
PCIe Gen3-x16
728 cores and 4x Kepler GPU
S26361-F2222-E924
PGRA CP NVIDIA GRID K2
NVIDIA GRID K2
8GB GDDR5 Memory
PCIe Gen3-x16
3.072 cores and 2x Kepler GPU
for shared and dedicated virtual graphic
max. 1x per system
for shared and dedicated virtual graphic
max. 1x per system
power cables from PSU are cabled
when ordering GPGPU ex factroy
Riser card for GPGPU is part of delivery
no PCIe bracket attached
G
Fujitsu Technology Solutions x86 PRIMERGY Serve
15 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
F
V
Section
Memory
- There are 8 memory slots per CPU for max.
512GB LRDIMM (8x 64GB 8R)
128GB RDIMM (8x 16GB 2R)
=> max. 1.024GB for two CPU`s (512GB per CPU), using LRDIMM
- The memory area is divided into 4 channels per CPU with 2 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2
Registered and LR DIMMs memory modules can be selected
No mix of registered and load reduced modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
In a single DIMM per channel configuration
In a 2 DIMMs per channel configuration, memory will operate at 1.35V or 1.5V.
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
In the "Independent Channel Mode" following configuration is possible
- Each slot can optionally be equipped with any registered or load reduced or unbuffered DDR3 modules:
No mix of registered and load reduced modules allowed.
"Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules per CPU
S26361-F3694-E2
Performance Mode Installation
Number of memory modules is always 4 / CPU, so all channels are populated and the max. memory performance can be achieved.
Four identical memory modules will be equipped in one memory bank to achieve highest memory performance. All four modules are active
and full capacity can be used.
1x per CPU Multiple of 4 identical modules to be configured per CPU
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
- one DDR3 unbuffered ECC mem. Module, 1.35V
1333MHz supported with up to 2DPC (8 modules/CPU) and 1.35V
1600MHz supported with up to 2DPC (8 modules/CPU) and 1.5V
Choose up to 8 order codes per CPU
8GB (1x8GB) 2Rx8 L DDR3-1600 U ECC
S26361-F3807-E515 Special release only
Registered Memory (RDIMM) with SDDC (chipkill) support
- one DDR3 registered ECC mem. Module, 1.35V
Note 1)
1333MHz supported with up to 2DPC (8 modules/CPU) and 1.35V
Max. DDR3 memory speed depends on the memory configuration
1600MHz supported with up to 2DPC (8 modules/CPU) and 1.5V
(No of mem modules per channel) as well as on the CPU type.
Choose up to 8 order codes per CPU
The memory channel with the lowest speed defines the speed
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC
S26361-F3781-E614
8GB (1x8GB) 1Rx4 L DDR3-1600 R ECC
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC
S26361-F3781-E615
S26361-F3781-E616
of all CPU channels in the system, also for the channels of the
second CPU if configured.
For real memory speed (depending on memory type / population),
please check the spreadsheet "Memory speed" below
Registered Memory (RDIMM) with SDDC (chipkill) support
8 per
- one DDR3 registered ECC mem. Module, 1.5V
CPU, max.
1866MHz supported with up to 2DPC (4 modules/CPU)
2 modules
per channel
Choose up to 8 order codes per CPU
16GB (1x16GB) 2Rx4 DDR3-1866 R ECC
S26361-F3793-E616
Registered Memory (RDIMM) no SDDC (chipkill) support
Note 2)
- one DDR3 registered ECC mem. Module, 1.5V
Mix of memory modules is only possible within the same group
No mix with any other types of memory modules possible
1866MHz supported with up to 2DPC (4 modules/CPU)
Note 3)
Choose up to 8 order codes per CPU
8GB (1x8GB) 2Rx8 DDR3-1866 R ECC
1,866MHz@2DPC will be available on 03/2014
S26361-F3793-E615
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 8 order codes per CPU
32GB (1x32GB) 4Rx4 L DDR3-1600 LR ECC
64GB (1x64GB) 8Rx4 L DDR3-1333 LR ECC
S26361-F3782-E617
S26361-F3783-E618 as soon as available
G
Fujitsu Technology Solutions x86 PRIMERGY Server
16 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Memory Configuration PRIMERGY CX2y0 S2
Each CPU offers 8 Slots for DDR3 Memory Modules organised in 2 Banks and 4 Channels.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 2 different kinds of DDR3 Memory Modules available: RDIMM and LRDIMM
RDIMM / LRDIMM offer different functionality. Mix of RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode
Configuration
RDIMM
UDIMM
Application
LRDIMM
RDIMM
x8
x4
x4
yes
SDDC (chipkill) support
any
no
yes
detect multi-bit errors
Performance Mode
4 identical Modules / Bank
yes
yes
yes
offers maximum performance and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity
Min. Memory per CPU
Max. Memory per CPU
Max. Memory per System
Configuration
4 Module / CPU
8 Modules / CPU
16 Modules / System
UDIMM
1x 8GB
8x 8GB
128GB
RDIMM
LRDIMM
1x 4GB
1x 32GB
8x 16GB
8x 64GB
256GB
1024GB
Notes
with one CPU
with one CPU
if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Mem . Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC) and voltage of
installed memory module
RDIMM 1866MHz
Voltage setting (BIOS)
1.5V[default]
1
DPC
2
1.35V
1
U/RDIMM 1600MHz
1.5V[default]
2
1
2
1.35V
1
2
LRDIMM 1600MHz
(4Rx4)
1.5V[default]
1
2
1.35V
1
2
LRDIMM 1333MHz
(8Rx4)
1.5V[default]
1
1.35V
2
1
2
DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC
CPU with 1866MHz DDR3 Bus
1866
1866 *
-
-
1600
1600
1333
1333
1600
1600
1600
1600
1066
1066
1066
1066
CPU with 1600MHz DDR3 Bus
1600
1600
-
-
1600
1600
1333
1333
1600
1600
1600
1600
1066
1066
1066
1066
CPU with 1333MHz DDR3 Bus
1333
1333
-
-
1333
1333
1333
1333
1333
1333
1333
1333
1066
1066
1066
1066
* 1,866MHz@2DPC will be available on 03/2014
1R - Single Rank
2R - Dual Rank
4R - Quad Rank
8R - Eight Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I
black sockets
Bank II blue sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2
up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU
Bank II on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
(can not be populated by UDIMM or 4R RDIMM memory modules)
- See below and next page for a detailed descriptions of the memory configuration supported.
Fujitsu Technology Solutions x86 PRIMERGY Server
17 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
G
VI
Section
Drive bay for basic unit
CX400 S2 3,5" HDD cage standard (S26361-K1476-V135)
for up to 3x HDD per CX250 S2 or up to 3x HDD for CX270 S2
CX400 S2 2,5" HDD cage standard (S26361-K1476-V125)
for up to 6x HDD per CX250 S2 or up to 6x HDD for CX270 S2
For Raid level 0 / 1 / 10 the LSI SW Raid for up to 4x HDD drives can be used
For SAS Drives or Raid level 5 or for Raid with more than 4x SATA HDD an optional
Raid card (either Mezzanaine or LP Ctr.) has to be used.
For CX250 S2 a SAS Raid mezzanine card is needed
For CX270 S2 a LP card has to be configured.
Max. HDD number per node
CX400 S2 3.5" HDD cage
Onb. SATA Ctrl
Opt. RAID card
Onb. SATA Ctrl
CX270 S2
Opt. RAID card
CX250 S2
SAS
0
3
0
3
SATA
3
3
3
3
CX400 S2 2.5" HDD cage
SAS
0
6
0
4
SATA
4
6
4
4
Max. HDD number per node in case of E5-2637 v2 (130W/4C) / E5-2643 v2(130W/6C) CPU
System become degraded performance at more than 30 deg-C environment for E5-2637/2643 V2
CX400 S2 3.5" HDD cage
Onb. SATA Ctrl
Opt. RAID card
Onb. SATA Ctrl
CX270 S2
Opt. RAID card
CX250 S2
SAS
0
1
0
2
SATA
1
1
2
2
CX400 S2 2.5" HDD cage
SAS
0
4
0
4
SATA
4
4
4
4
H
Fujitsu Technology Solutions x86 PRIMERGY Serve
18 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
H
VII
Section
Hard disks drives
Non-RAID configuration w/ Intel RST is not supported to Onboard SATA Ctrl
For MegaSR Raid 0/1 up to 4x SATA HDD can be connected to onboard chipset
Onboard SATA Ctrl is not supporting Vmware ESXi
For SAS HDD or Raid level 5 or more than 4x SATA HDD in a Raid configuration
a SAS Raid option needs to be ordered additionally, please refer controller section
Mixed configurations with SATA drives and SAS drives are not allowed per node
All not needed HDD slots needs to be filled with an dummy HDD frame
One UFM (USB Flash Module) can be configured
The UFM is bundeld with Vmware offering
HDD/SSD on CX400 S2 3.5" HDD cage standard
Solid State Disk, Mainstream Endurance*
SSD SATA 6Gb/s 2.5" with 3.5" hot plug/hot replace tray
100GB, Mainstream Performance
200GB, Mainstream Performance
400GB, Mainstream Performance
800GB, Mainstream Performance
SSD SAS 12Gb/s 2.5" with 3.5" hot plug/hot replace tray
200GB, Enterprise Performance
400GB, Enterprise Performance
800GB, Enterprise Performance
1.6TB, Enterprise Performance
max. 3x per system
S26361-F5305-E100
S26361-F5305-E200
S26361-F5305-E400
S26361-F5305-E800
S26361-F5300-E200
S26361-F5300-E400
S26361-F5300-E800
S26361-F5300-E160
Interface SAS12Gb/s and SAS 6Gb/s.
SAS 12Gb/s support is not released
*) SSD Mainstream Endurance
10DWPD over 5y
SAS Disk Drive
HDD SAS 6Gb/s 2.5" with 3.5" hot plug/hot replace tray
300GB 10000rpm,<4,5ms, 32MB Cache
450GB 10000rpm,<4,5ms, 32MB Cache
600GB 10000rpm,<4,5ms, 32MB Cache
900GB 10000rpm,<4,5ms, 32MB Cache
1,2TB 10000rpm,<4,5ms, 64MB Cache
146GB 15krpm,<4,5ms, 32MB Cache
300GB 15krpm,<4,5ms, 32MB Cache
max. 3x per system
S26361-F5244-E130
S26361-F5244-E145
S26361-F5244-E160
S26361-F5244-E190
S26361-F5244-E112
S26361-F5245-E514
S26361-F5245-E530
SATA Disk Drive
HDD SATA 6Gb/s 3.5" with 3.5" hot plug/hot replace tray
500GB 7.2krpm,<9,0ms, 64MB Cache
1TB 7.2krpm,<9,0ms, 64MB Cache
2TB 7.2krpm,<9,0ms, 64MB Cache
3TB 7.2krpm,<9,0ms, 64MB Cache
4TB 7.2krpm,<9,0ms, 64MB Cache
max. 3x per system
S26361-F3711-E500
S26361-F3711-E100
S26361-F3711-E200
S26361-F3711-E300
S26361-F3711-E400
HDD/SSD on CX400 S2 2.5" HDD cage standard
Solid State Disk, Mainstream Endurance*
SSD SATA 6Gb/s 2.5" with 2.5" hot plug/hot replace tray
100GB MLC, Mainstream Performance
200GB MLC, Mainstream Performance
400GB MLC, Mainstream Performance
100GB, Mainstream Performance
200GB, Mainstream Performance
400GB, Mainstream Performance
800GB, Mainstream Performance
S26361-F5226-E100
S26361-F5226-E200
S26361-F5226-E400
S26361-F5304-E100
S26361-F5304-E200
S26361-F5304-E400
S26361-F5304-E800
SSD SAS 6Gb/s 2.5" with 2.5" hot plug/hot replace tray
100GB MLC, Enterprise Performance
200GB MLC, Enterprise Performance
400GB MLC, Enterprise Performance
S26361-F4992-E100
S26361-F4992-E200
S26361-F4992-E200
SSD SAS 12Gb/s 2.5" with 2.5" hot plug/hot replace tray
200GB, Enterprise Performance
400GB, Enterprise Performance
800GB, Enterprise Performance
1.6TB, Enterprise Performance
max. 6x for CX250 S2 / 4x for CX270 S2
S26361-F5299-E200
S26361-F5299-E400
S26361-F5299-E800
S26361-F5299-E160
Interface SAS12Gb/s and SAS 6Gb/s.
SAS 12Gb/s support is not released
SAS Disk Drive 2.5"
HDD SAS 6Gb/s 2.5" with 2.5" hot plug/hot replace tray
300GB 10000rpm,<4,5ms, 32MB Cache
450GB 10000rpm,<4,5ms, 32MB Cache
600GB 10000rpm,<4,5ms, 32MB Cache
900GB 10000rpm,<4,5ms, 32MB Cache
1,2TB 10000rpm,<4,5ms, 64MB Cache
146GB 15krpm,<4,5ms, 32MB Cache
300GB 15krpm,<4,5ms, 32MB Cache
max. 6x for CX250 S2 / 4x for CX270 S2
*) SSD Mainstream Endurance
10DWPD over 5y
S26361-F4568-E130
S26361-F4568-E145
S26361-F4568-E160
S26361-F4568-E190
S26361-F4568-E112
S26361-F4568-E514
S26361-F4568-E530
SATA Disk Drive 2.5"
HDD SATA 6Gb/s 2.5" with 2.5" hot plug/hot replace tray
250GB 7.2krpm,<9,5ms, 64MB Cache
S26361-F3709-E250
500GB 7.2krpm,<9,5ms, 64MB Cache
S26361-F3709-E500
1TB 7.2krpm,<9,5ms, 64MB Cache
S26361-F3709-E100
max. 6x for CX250 S2 / 4x for CX270 S2
H1
Fujitsu Technology Solutions x86 PRIMERGY Serve
19 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
I
VIII
Section
Onboard SW Raid 0/1, additional Raid options
For more than 4 hard disks in a Raid configuration, or for use of SAS HDD / SSD; as well as
for using Raid level 5 configuration; one of the following modular RAID-controllers is required
For CX270 S2 use of PCI-e standard slot (via Riser)
For only single HDD configuration
S26361-F3554-E8
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2008
LSI MegaRAID
no Cache, no BBU
RAID 0, 1 & 10
S26361-F3554-E512
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2108
LSI MegaRAID
512MB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
Intel RSTe is also supported
Support for 3Gb/s and 6Gb/s
optional BBU
Intel RSTe can be set on BIOS
SATA and SAS hard drives
PCIe x8
Low-profile MD2 form factor
max. 1x per system
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe x8
Low-profile MD2 form factor
max. 1x per system
Onboard SATA controller
no Cache, no BBU
RAID 0 & 1
1x integrated per system
RAID Ctrl SAS is required
for Vmware ESXi installation to HDD.
Onbard SATA Connection is not
supporting Vmware ESXi
BBU max. 1x per system possible
for loose delivery please order
S26361-F4575-L510
S26361-F4575-E510
Cache Battery Backup Unit
with cable set
max. 1x per Controller
special release
RAID ctrl SAS 6G are also available
as loose delivery
S26361-F3554-L8 (LSISAS2008)
S26361-F3554-L512 (LSISAS2108)
Please note, cable kit is also required to order
for RAID Ctrl SAS 6G
For 3.5" HDD cage, please order
S26361-F4575-L273
For 2.5" HDD cage,
please order
S26361-F4575-L274
1x
I
Fujitsu Technology Solutions x86 PRIMERGY Serve
20 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
I
For CX250 S2 use of PCI-e Mezzanine card
For more than 4 hard disks in a Raid configuration, or for use of SAS HDD / SSD; as well as
for using Raid level 5 configuration; one of the following modular RAID-controllers is required
Onboard SATA controller
no Cache, no BBU
RAID 0 & 1
1x integrated per system
For only single HDD configuration
Intel RSTe is also supported
Intel RSTe can be set on BIOS
RAID Ctrl SAS is required
for Vmware ESXi installation to HDD.
Onbard SATA Connection is not
supporting Vmware ESXi
S26361-F4575-E512
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2108
LSI MegaRAID
512MB Cache with ECC
RAID 0, 1, 10, 5
optional BBU
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe x8
Mezzanine card
max. 1x per system
BBU max. 1x per system possible
for loose delivery please order
S26361-F4575-L510
S26361-F4575-E510
Cache Battery Backup Unit
with 16 cm cable set
max. 1x per Controller
special release
The mezzanine card is also available
as loose delivery
S26361-F4575-L512
Please note, cable kit is also required to order
for the mezzanine card
For 2.5" HDD cage, please order
S26361-F4575-L251
For 3.5" HDD cage, please order
S26361-F4575-L252
J
Fujitsu Technology Solutions x86 PRIMERGY Serve
21 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
J
IX
Section
Onboard SW Raid 0/1, additional Raid options
For CX250 S2
SAS controller
S26361-F3628-E201
SAS Controller 6Gb/s 8 port LP
LSI SAS9200-8e LP
PCIe 2.0
ext: 8 port
1x
Supported only for CX250 S2
PCIe x4, Low Profile
max. 1x per CX250 S2
K
Fujitsu Technology Solutions x86 PRIMERGY Serve
22 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
K
X-I
Section
Communication / Network for CX250 S2
2x Gbit LAN on-board.
1x service LAN (either shared or dedicated)
2x Gigabit (Dualport) Ethernet Contr.
onboard
Intel LAN I350 (Powerville)
ext: 2x RJ 45 connector
Mezz slot on CX250 S2
Mezzcard) 10GbE 2-Port SFP+ for MMF Module
S26361-F4575-E2
Mezzanine card for CX250 S2
1x w/o HW RAID 10 Gigabit Ethernet Contr. dual port SFP+
0x w/ HW RAID Eth Ctrl 2x10Gbit PCIe x8 SFP+
Intel Niantic based dual port 10Gb NIC
PCIe x8,Mezzanaine Card
ext: 2x SFP+ cage
max. 1x per system
S26361-F3986-E3
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 50µm FO cabling
ext:LC-SR-connector
max. 2x per controller
The controller is delivered without SFP+ modules for optical cables, these must be
ordered separately. Without SFP+ modules copper twinax cables are supported.
The mezzanaine card is also available
as loose delivery: S26361-F4575-L2
S26361-F3986-E4
SFP+ Module SMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 9µm FO cabling
ext:LC-LR-connector
max. 2x per controller
The SFP+ Module is also available as loose delivery
S26361-F3986-L3
The SFP+ Module is also available as loose delivery
S26361-F3986-L4
Instead SFP+ Modules, SFP+ twinax cables from
the switch vendors may be used
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
S26361-F3989-E600 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Fujitsu branded cable
max. 2x per controller
S26361-F3873-E500 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Brocade branded cable
max. 2x per controller
S26361-F4571-E500 *)
SFP+ passive twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Cisco branded cable
max. 2x per controller
*) in SA only
shown in
cabling view
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ aktives Twinax Kabel Fujitsu 2m
S26361-F3989-L105
SFP+ aktives Twinax Kabel Fujitsu 5m
S26361-F3989-L110
SFP+ aktives Twinax Kabel Fujitsu 10m
S26361-F3873-L501
SFP+ aktives Twinax Kabel Brocade 1m
S26361-F3873-L503
SFP+ aktives Twinax Kabel Brocade 3m
S26361-F3873-L505
SFP+ aktives Twinax Kabel Brocade 5m
S26361-F4571-L101
SFP+ passives Twinax Kabel Cisco 1m
S26361-F4571-L103
SFP+ passives Twinax Kabel Cisco 3m
S26361-F4571-L105
SFP+ passives Twinax Kabel Cisco 5m
S26361-F4571-L107
SFP+ aktives Twinax Kabel Cisco 7m
S26361-F4571-L110
SFP+ aktives Twinax Kabel Cisco 10m
Mezzcard for 10GbE-T 2-Port
S26361-F4575-E3
Mezzanine card for CX250 S2
10 GBASE-T Ethernet Contr. dual port
Eth Ctrl 2x10Gbit PCIe x8
Intel Twinville based dual port 10Gb NIC
PCIe x8,Mezzanaine Card
ext: RJ45 plug, Cat 6
max. 1x per system
1x w/o HW RAID
0x w/ HW RAID
The mezzanaine card is also available
as loose delivery: S26361-F4575-L3
PCIe slot on CX250 S2
1Gbit/s Ethernet Adapter
S26361-F4610-E202
(I350-T2)
Gbit Ethernet Controller Dual 1000TX LP
PLAN CP 2x1Gbit Cu Intel I350-T2 LP
Intel Powerville based 2 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 1x per system
S26361-F4610-E204
(I350-T4)
Gbit Ethernet Controller Quad 1000TX LP
PLAN CP 4x1Gbit Cu Intel I350-T4 LP
Intel Powerville based 4 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 1x per system
Loose delivery with FH and LP bracket:
I350-T2
S26361-F4610-L502
I350-T4
S26361-F4610-L504
1x
S26361-F3752-E202
Eth Ctrl 2x10GBase-T PCIe x8 X540-T2 lp
Intel Twinville based 2 port Server Adapter
PCIe x4, Low Profile
ext: for RJ45-plug, Cat 6
max. 1x per system
The adapter is also available as loose delivery with
FH and LP bracket included: S26361-F3752-L502
L
Fujitsu Technology Solutions x86 PRIMERGY Serve
23 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
L
C) 10GbE 2-Port SFP+ for MMF Module
S26361-F3629-E202
(D2755)
10 Gigabit Ethernet Contr. dual port SFP+
Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+
Intel Niantic based dual port 10Gb NIC
PCIe x8, Low Profile, full height (FH) bracket
ext: 2x SFP+ cage
max. 1x per system
S26361-F3986-E3
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 50µm FO cabling
ext:LC-SR-connector
max. 2x per controller
The controller is delivered without SFP+ modules for optical cables, these must be
ordered separately. Without SFP+ modules copper twinax cables are supported.
The adapter is also available as loose delivery with
FH and LP bracket included: S26361-F3629-L502
S26361-F3986-E4
SFP+ Module SMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 9µm FO cabling
ext:LC-LR-connector
max. 2x per controller
The SFP+ Module is also available as loose delivery
S26361-F3986-L3
The SFP+ Module is also available as loose delivery
S26361-F3986-L4
Instead SFP+ Modules, SFP+ twinax cables from
the switch vendors may be used
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
S26361-F3989-E600 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Fujitsu branded cable
max. 2x per controller
S26361-F3873-E500 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Brocade branded cable
max. 2x per controller
S26361-F4571-E500 *)
SFP+ passive twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Cisco branded cable
max. 2x per controller
*) in SA only
shown in
cabling view
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ aktives Twinax Kabel Fujitsu 2m
S26361-F3989-L105
SFP+ aktives Twinax Kabel Fujitsu 5m
S26361-F3989-L110
SFP+ aktives Twinax Kabel Fujitsu 10m
S26361-F3873-L501
SFP+ aktives Twinax Kabel Brocade 1m
S26361-F3873-L503
SFP+ aktives Twinax Kabel Brocade 3m
S26361-F3873-L505
SFP+ aktives Twinax Kabel Brocade 5m
S26361-F4571-L101
SFP+ passives Twinax Kabel Cisco 1m
S26361-F4571-L103
SFP+ passives Twinax Kabel Cisco 3m
S26361-F4571-L105
SFP+ passives Twinax Kabel Cisco 5m
S26361-F4571-L107
SFP+ aktives Twinax Kabel Cisco 7m
S26361-F4571-L110
SFP+ aktives Twinax Kabel Cisco 10m
L
Fujitsu Technology Solutions x86 PRIMERGY Serve
24 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
L
D) Fibre Channel over Ethernet
S26361-F3592-E202
10GBit/s CNA
Emulex
OCe10102
2 channel 10GBit/sec CNA
SFP+ Cage
PCIe x8, 170mm
max. 1 per system
Loose Delivery: S26361-F3592-L202
S26361-F3592-E108
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet FO cabling
ext:LC-connector
max. 2x per controller
The SFP+ Module is also available as loose delivery
S26361-F3592-L108
Instead SFP+ Modules, SFP+ twinax cables from
the switch vendors may be used
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
S26361-F3989-E600 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Fujitsu branded cable
max. 2x per controller
S26361-F3873-E500 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Brocade branded cable
max. 2x per controller
S26361-F4571-E500 *)
SFP+ passive twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Cisco branded cable
max. 2x per controller
*) in SA only
shown in
cabling view
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ aktives Twinax Kabel Fujitsu 2m
S26361-F3989-L105
SFP+ aktives Twinax Kabel Fujitsu 5m
S26361-F3989-L110
SFP+ aktives Twinax Kabel Fujitsu 10m
S26361-F3873-L501
SFP+ aktives Twinax Kabel Brocade 1m
S26361-F3873-L503
SFP+ aktives Twinax Kabel Brocade 3m
S26361-F3873-L505
SFP+ aktives Twinax Kabel Brocade 5m
S26361-F4571-L101
SFP+ passives Twinax Kabel Cisco 1m
S26361-F4571-L103
SFP+ passives Twinax Kabel Cisco 3m
S26361-F4571-L105
SFP+ passives Twinax Kabel Cisco 5m
S26361-F4571-L107
SFP+ aktives Twinax Kabel Cisco 7m
S26361-F4571-L110
SFP+ aktives Twinax Kabel Cisco 10m
E) Infiniband HCA's
S26361-F4475-E122/E222
PIB EP QLE7340e/42e
Intel IB HCA 1x / 2x 40Gb
PCIe 2.0 (5,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 1x per system
S26361-F4475-E103/E203
IB HCA 40Gb 1 and 2 port QDR enhanced
IB HCA 1x / 2x 40Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 1x per system
1x
loose delivery: S26361-F4475-L122/L222
Low Profile PCIe form factor with
exchangeable Full Height (FH)
or Low Profile (LP) bracket
S26361-F4533-E102/E202
IB HCA 56Gb 1 and 2 port FDR
IB HCA 1x / 2x 56Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 1x per system
loose delivery: S26361-F4475-L103/L203
loose delivery: S26361-F4533-L102/L202
Low Profile PCIe form factor with
exchangeable Full Height (FH)
or Low Profile (LP) bracket
only within a rack
configuration
S26361-F3996-E556
InfiniBand Cu Cable 56Gb
customized
QSFP, 1m and 3m
max. 2x per adapter
If additional length of copper cable or optical cable are needed,
then they must be ordered from the cable vendor directly
Copper cable are also available for loose delivery as
S26361-F3996-L561, QSFP, 56Gb, 1m
S26361-F3996-L563, QSFP, 56Gb, 3m
L
Fujitsu Technology Solutions x86 PRIMERGY Serve
25 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
L
F) Fibre channel HCA's
S26361-F3961-E201
8GBit/s FC Controller
Emulex
LPe1250, low profile bracket
1 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 1x per system
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
S26361-F3961-E202
8GBit/s FC Controller
Emulex
LPe12002, low profile bracket
2 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 1x per system
S26361-F4994-E202
16GBit/s FC Controller
Emulex
LPe16002, low profile bracket
2 channel 16GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x8, 170mm
max. 1x per system
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
loose delivery: S26361-F3961-L201/L202
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
loose delivery: S26361-F4994-L502
M
Fujitsu Technology Solutions x86 PRIMERGY Serve
26 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
K
X-II
Section
Communication / Network for CX270 S2
2x Gbit LAN on-board.
1x service LAN (either shared or dedicated)
2x Gigabit (Dualport) Ethernet Contr.
onboard
Intel LAN I350 (Powerville)
ext: 2x RJ 45 connector
PCIe slot on CX270 S2
1Gbit/s Ethernet Adapter
S26361-F4610-E202
(I350-T2)
Gbit Ethernet Controller Dual 1000TX LP
PLAN CP 2x1Gbit Cu Intel I350-T2 LP
Intel Powerville based 2 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 2x per system
S26361-F4610-E204
(I350-T4)
Gbit Ethernet Controller Quad 1000TX LP
PLAN CP 4x1Gbit Cu Intel I350-T4 LP
Intel Powerville based 4 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 1x per system
Loose delivery with FH and LP bracket:
I350-T2
S26361-F4610-L502
I350-T4
S26361-F4610-L504
2x w/o HW RAID
1x w/ HW RAID
S26361-F3752-E202
Eth Ctrl 2x10GBase-T PCIe x8 X540-T2 lp
Intel Twinville based 2 port Server Adapter
PCIe x4, Low Profile
ext: for RJ45-plug, Cat 6
max. 2x per system
The adapter is also available as loose delivery with
FH and LP bracket included: S26361-F3752-L502
C) 10GbE 2-Port SFP+ for MMF Module
S26361-F3629-E202
(D2755)
10 Gigabit Ethernet Contr. dual port SFP+
Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+
Intel Niantic based dual port 10Gb NIC
PCIe x8, Low Profile, full height (FH) bracket
ext: 2x SFP+ cage
max. 2x per system
S26361-F3986-E3
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 50µm FO cabling
ext:LC-SR-connector
max. 2x per controller
The controller is delivered without SFP+ modules for optical cables, these must be
ordered separately. Without SFP+ modules copper twinax cables are supported.
The adapter is also available as loose delivery with
FH and LP bracket included: S26361-F3629-L502
S26361-F3986-E4
SFP+ Module SMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 9µm FO cabling
ext:LC-LR-connector
max. 2x per controller
The SFP+ Module is also available as loose delivery
S26361-F3986-L3
The SFP+ Module is also available as loose delivery
S26361-F3986-L4
Instead SFP+ Modules, SFP+ twinax cables from
the switch vendors may be used
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
S26361-F3989-E600 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Fujitsu branded cable
max. 2x per controller
S26361-F3873-E500 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Brocade branded cable
max. 2x per controller
S26361-F4571-E500 *)
SFP+ passive twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Cisco branded cable
max. 2x per controller
*) in SA only
shown in
cabling view
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ aktives Twinax Kabel Fujitsu 2m
S26361-F3989-L105
SFP+ aktives Twinax Kabel Fujitsu 5m
S26361-F3989-L110
SFP+ aktives Twinax Kabel Fujitsu 10m
S26361-F3873-L501
SFP+ aktives Twinax Kabel Brocade 1m
S26361-F3873-L503
SFP+ aktives Twinax Kabel Brocade 3m
S26361-F3873-L505
SFP+ aktives Twinax Kabel Brocade 5m
S26361-F4571-L101
SFP+ passives Twinax Kabel Cisco 1m
S26361-F4571-L103
SFP+ passives Twinax Kabel Cisco 3m
S26361-F4571-L105
SFP+ passives Twinax Kabel Cisco 5m
S26361-F4571-L107
SFP+ aktives Twinax Kabel Cisco 7m
S26361-F4571-L110
SFP+ aktives Twinax Kabel Cisco 10m
L
Fujitsu Technology Solutions x86 PRIMERGY Serve
27 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
L
E) Infiniband HCA's
S26361-F4475-E122/E222
PIB EP QLE7340e/42e
Intel IB HCA 1x / 2x 40Gb
PCIe 2.0 (5,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 1x per system
S26361-F4475-E103/E203
IB HCA 40Gb 1 and 2 port QDR enhanced
IB HCA 1x / 2x 40Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 1x per system
1x
loose delivery: S26361-F4475-L122/L222
Low Profile PCIe form factor with
exchangeable Full Height (FH)
or Low Profile (LP) bracket
S26361-F4533-E102/E202
IB HCA 56Gb 1 and 2 port FDR
IB HCA 1x / 2x 56Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max.1x per system
loose delivery: S26361-F4475-L103/L203
loose delivery: S26361-F4533-L102/L202
Low Profile PCIe form factor with
exchangeable Full Height (FH)
or Low Profile (LP) bracket
only within a rack
configuration
S26361-F3996-E556
InfiniBand Cu Cable 56Gb
customized
QSFP, 1m and 3m
max. 2x per adapter
If additional length of copper cable or optical cable are needed,
then they must be ordered from the cable vendor directly
Copper cable are also available for loose delivery as
S26361-F3996-L561, QSFP, 56Gb, 1m
S26361-F3996-L563, QSFP, 56Gb, 3m
D) Fibre Channel over Ethernet
S26361-F3592-E202
10GBit/s CNA
Emulex
OCe10102
2 channel 10GBit/sec CNA
SFP+ Cage
PCIe x8, 170mm
max. 1 per system
1x
Loose Delivery: S26361-F3592-L202
S26361-F3592-E108
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet FO cabling
ext:LC-connector
max. 2x per controller
The SFP+ Module is also available as loose delivery
S26361-F3592-L108
Instead SFP+ Modules, SFP+ twinax cables from
the switch vendors may be used
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
S26361-F3989-E600 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Fujitsu branded cable
max. 2x per controller
S26361-F3873-E500 *)
SFP+ active twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Brocade branded cable
max. 2x per controller
S26361-F4571-E500 *)
SFP+ passive twinax cable
customized twinax cable for
full rack setup ex factory
cable length is selected by
requirement in the factory
Cisco branded cable
max. 2x per controller
*) in SA only
shown in
cabling view
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ aktives Twinax Kabel Fujitsu 2m
S26361-F3989-L105
SFP+ aktives Twinax Kabel Fujitsu 5m
S26361-F3989-L110
SFP+ aktives Twinax Kabel Fujitsu 10m
S26361-F3873-L501
SFP+ aktives Twinax Kabel Brocade 1m
S26361-F3873-L503
SFP+ aktives Twinax Kabel Brocade 3m
S26361-F3873-L505
SFP+ aktives Twinax Kabel Brocade 5m
S26361-F4571-L101
SFP+ passives Twinax Kabel Cisco 1m
S26361-F4571-L103
SFP+ passives Twinax Kabel Cisco 3m
S26361-F4571-L105
SFP+ passives Twinax Kabel Cisco 5m
S26361-F4571-L107
SFP+ aktives Twinax Kabel Cisco 7m
S26361-F4571-L110
SFP+ aktives Twinax Kabel Cisco 10m
F) Fibre channel HCA's
S26361-F3961-E201
8GBit/s FC Controller
Emulex
LPe1250, low profile bracket
1 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 2x per system
2x
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
S26361-F3961-E202
8GBit/s FC Controller
Emulex
LPe12002, low profile bracket
2 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 1x per system
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
loose delivery: S26361-F3961-L201/L202
1x
S26361-F4994-E202
16GBit/s FC Controller
Emulex
LPe16002, low profile bracket
2 channel 16GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x8, 170mm
max. 1x per system
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
loose delivery: S26361-F4994-L502
M
Fujitsu Technology Solutions x86 PRIMERGY Serve
28 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
L
Section
XI
System Management Products (RemoteView)
AST2300 (integrated Remote Management Controller) onboard server management
Controller with dedicated 10/100/ Service LAN-port and integrated graphics.
Dedicated 10/100 Service LAN-port at the rear side.
The Service LAN-port can be switched alternatively on standard Gbit LAN port
S26361-F4575-E30
Note: can only be enabled ex factory by ordering this
iKVM advanced pack
order code.
integrated remote management controller
There is no later upgrade possible, no -L number.
activation key for
graphical console redirection
and remote media redirection
max. 1x per system
Section
XII
Miscellaneous
Options and other peripherals
For other options, refer to SystemArchitect and Pricelist
These options are supplied lose with the shipment
For suitable peripherals for this product, please refer to SystemArcitect
End PRIMERGY CX2y0 S1
Fujitsu Technology Solutions x86 PRIMERGY Serve
29 of 30
System configurator and order-information guide
PRIMERGY CX400 S2 / CX2y0 S2
Status 2014-12-30
Change Report
Date
Order number
Changes
S26361-F2222-E40 / L40 Added NVIDIA K40 GPGPU
2014-06-30 S26361-F3301-E123
Added certification for India
2014-08-29
2014-06-20
2014-05-27
2014-04-28
2014-04-14
2014-04-08
2014-02-28
2014-02-14
2013-09-18
2013-09-06
S26361-F4575--E3 / L3
S26361-F2222-E924
D3035/D3045 GbE cards removed
Release single SATA HDD configuration w/ Intel RSTe
Release modular RAID Lynx2 for CX270 S2
Release FCoE 10102 / FC LPe1250 / FC LPe12002 / FC Lpe 16002 for CX270 S2
added 10Gbase-T mezz card for CX250 S2
added NVIDIA GRID K2 and rework GRID section
LAN card I350-T/I350-T4 added, 2.5" HDD/SSD on CX400 S2 3.5" added
External SAS HBA 9200-8e added, FC/CNA for CX270 S2 added
SAS SSD and SAS 1.2TB HDD added
Grid K1 and 1,866MHz@2DPC added
Release CX270 S2 w/o GPGPU or Xeon Phi
Initial version
Fujitsu Technology Solutions x86 PRIMERGY Serve
30 of 30

Download Report