Professional LED Photography Light User Manual Sonnon DL-914 Overview Before using this product , you must read the manual and fully understand how to use it and ensure that you can easily handle the operation method and also use it properly . 1 Precautions 1 Make sure the power adapter, power cable and LED light are installed correctly before power-on. 2 This product involved in electronic product accessories which may cause the failure to use of this 3 Do not put this product in strong vibration, or it may cause fault of this product. device. But this possibility is very low. 4 Power off the device and remove the batteries during long periods of non-use. 5 Do not expose this product in high temperature locations, such as confined car exposed to strong 6 Keep it dry. Do not touch this product with wet hand. Do not expose this product to water or rain, direct sunlight, control panel and other overheating places. or you may not be able to use it. 7 Do not use it inflammables gas, or it may cause explosion or fire. 8 This product involved in battery. Please strictly follow the corresponding operations related to battery, or it may cause explosion or fire. Content Function Introduction Thanks for choosing the Pixel Sonnon DL-914 professional LED photography light. This product is an ideal choice for professional photography and video fill light. It will provide you with high performance configuration. With 2.4GHz digital wireless transmission system, its wireless transmission distance up to 50M; it supports wireless group brightness adjustment, 30 levels for option; it also supports group control, trigger with the Speedlite at the same time and other functions. The equipped large LCD screen makes the operations more simple and clear.The hardware is even more superior. With advanced drive circuit design, it guarantees lower loss conversion rate and makes it more eco-friendly and energy-saving. Using import high-end bulb which high index prefect color temperature and long life time, the lifetime up to 50,000hours. It's indispensable for professional photographers and videographers, making your shooting more creative. 2 Specifications System Mode:FSK 2.4GHz wireless digital transmission system Distance:Over 50M Trigger:Support wired , wireless triggering Antenna:Internal Antenna Power Consumption: Max.54W under steady mode LED Bulbs:900 pcs Trigger: Max. 80W under trigger mode Color Rending Index: 85 Color Temperature: 5600K Lumen: UP TO 4100LM Screen Display: Support Irradiate Distance: Max.6M Steady Level:30 levels for digital brightness adjustment Flash GN: 28 Group:Group ABC,support steady mode and trigger group sync mode DC Port: DC 12-19V ＞5Ah Power Adapter: In AC110V-240V, Out 15V or 19V, Max 5AH SYNC Port: Port for triggering Operating Temperature:-20—40°C Irradiate Angle:60 ° Lifetime:50,000 hours Dimensions:375X340X55mm Material: Aluminum Aloy Weight: 4.05KG Item Included After opened the package, please check the below items are included. If any accessory shown as below is Not included, please contact the dealer. Pr of essi onal ED L h P ot ogr aphy i g L ht Us er Manual Sonnon DL-914 Overview Bef o re usin g this pro duct, yo u must re ad the m an ual an d fully un ders tan d ho w to use it an d en sure that yo u can e as ily han dle the o pe ratio n m etho d an d als o us e it pro perly. White Color Filter 1pc 1 Power Cable 1pc User Manual 1pc Mounting Screw for Color Filter 4sets（2pcs） Bracket Mounting Screw 1set DL-A15 V- Mount AC Adapter Power Adapter 1pc 3 Name of Each Part Brightness Adjustment Dial LCD Screen SYNC Port Group A SYNC Switch A B C D Group B SYNC Switch Group C SYNC Switch DL-A15 V- Mount AC Adapter Trigger Set Switch Adapter Buckle Power Adapter DC Input Port Power Switch Rear View Barndoor Mounting Socket Elastic Nut LED light Panel U-shaped Bracket Front View 4 Name of Each Part Brightness Percentage Battery Icon Transmitter Icon Receiver Icon Lumen Color Filter Color Temperature Parameter Mounting Screw for Color Filter Barndoor Bracket Barndoor Trigger Set Icon Group C SYNC Icon Group A SYNC Icon Side View Group B SYNC Icon Bracket Mounting Screw LCD Screen Brightness Adjustment Dial: Turn this button to adjust LED brightness. LCD Screen: Show current parameters for LED light, such as: Lumen, battery source, color temperature, duty ratio, group and etc. SYNC Port: Port for triggering. Group A SYNC Switch: Group set switch.Click this button to ON or OFF. Group B SYNC Switch: Group set switch. Click this button to ON or OFF. Group C SYNC Switch: Group set switch. Click this button to ON or OFF. Trigger Setting Switch: Trigger set switch. Click this button to ON or OFF. Under steady mode, turn off this button.Under trigger mode, turn on this button. Adapter Buckle: Mounting adapter buckle. Lumen: Brightness can be adjusted from 275LM to 4100LM, 30 levels for option. Every level shows the corresponding Lumen. Color Temperature Parameter: 5600K. TX Icon: TX means transmitter coding signal. RX Icon: RX means receiver coding signal. Battery Icon: Full-bar battery level means normal power supply; and empty means power shortage. Brightness Percentage: Show the percentage of the brightness. 5 Installation Guide 1、U-Shaped Bracket and Mounting Screw Installation A B C D 1 1 2 2 DL-A15 V- Mount AC Adapter 3 4 2、Power Adapter Installation When installing power adapter, point at LED light and the bayonet of power adapter, and then push to the left to lock it. When removing power adapter, just press the power adapter locker. 6 Installation Guide 3、Barndoor Installation 4、 Color Filter Installation 7 Product Function Single Use 1、Switch on the power after power-on, LCD screen lights up to show current status and enter to steady mode.Now, the default brightness of this light as Minimum value. (See Figure 1) 2、After entered to steady mode, turn brightness adjustment switch to adjust LED brightness; light brightness divided into 30 levels from Minimum to Maximum, turn clockwise to increase brightness and turn anticlockwise to reduce brightness. (Shown as Figure 2) 1 2 Multi-lights Use When using multi Sonnon DL-914 LED lights together, the wireless brightness for every group can be adjusted freely. Before adjusting wireless brightness, you need to code the lights that will be needed to control. The lights can freely adjust and control each other until coding is completed. 1、First, set one LED light as transmitter for signal transmission, press an hold Group A sync switch of the LED light and turn on the power at the same time. And then press and hold Group B sync switch of another light and turn on the power at the same time. Release the sync switch until BIND RX will be displayed on the LCD screen. After coding succeeded, LED screen will back to the current interface. Restart the power switch of the transmitter signal LED light to complete coding. If you need to use multi LED lights together, repeat the coding setting steps of the receiver. After coding succeeded, just restart the signal transmission LED light. 8 Product Function 2、 After coding succeeded, the brightness of the same groups of the corresponding LED lights can freely adjust and control each other. When group setting is enabled, LCD screen will show the corresponding group. Turn it off to remove it. 3、 When ABC, AB on the same group, if need to adjust the brightness of the lights, subject to the brightness of Group A. When BC on the same group, if need to adjust the brightness of the lights, subject to the brightness of Group B. Adjustment can be made as long as the group that already opened is the same as any of the group. Trigger Sync Mode Sonnon DL-914 is equipped with wired or wireless triggering Wired Triggering When using wired triggering, you only need one Pixel PC-3.5 connecting cable. But your camera must be equipped with PC trigger port (If not, you may purchase the power adapter with PC port), connect PC port to camera, and then connect 3.5 port to LED light. When triggering, turn on the LED trigger set switch to trigger (when trigger sets witch opened, LED light will be off, at this time, it will enter to trigger status). If multi lights are needed to trigger, just coding without connecting them via cables one by one. Wireless Triggering When using wireless triggering, it needs to work with Pixel King Pro transmitter. Pixel King Pro transmitter is required to purchase separately. When using with King Pro for wireless triggering, please be sure to coding all the LED lights that will be joined. After coding succeeded, you may use it. 1、 When using King Pro transmitter for triggering, the coding steps as: press and hold Group B sync switch of the LED light and turn on the power at the same time. Release the sync switch until BIND RX will be displayed on the LCD screen. And then press the button C on the King PRO transmitter and turn on the power at the same time, at this time, King Pro LCD screen will show Coding… it means coding is in progress. After coding succeeded, the LCD screen of the LED light will be back to the current status. Then restart King Pro transmitter to complete coding.When triggering, you need to turn on the trigger set sync switch of the LED light. Now, the LED light will not be available, and it will enter to trigger status. Coding... OFF master 9 Product Function 2、 The group of King Pro transmitter is corresponding as that of LED light. After coding succeeded, it can be triggered as long as the groups of King Pro transmitter and LED light are opened correspondingly. 3、 If multi lights need to be triggered synchronously, just make coding with King Pro one by one. After coding succeeded, all the LED lights can be joined with King Pro for triggering. *When King Pro Group ABC are opened, all the LED lights can be joined in triggering as long as any of the group is opened;If Group A on the King Pro transmitter is opened, then it can control the Group A of the LED light to trigger;If Group B on the King Pro transmitter is opened, then it can control the Group B of the LED light to trigger; If Group B on the King Pro transmitter is opened, then it can control the Group C of the LED light to trigger;The group of King Pro transmitter is corresponding as that of LED light. Thanks for choosing Pixel Company's product and read this user manual. Should you have any questions, please contact the local dealer or login our website:http://www.pixelhk.com The instruction manual is dated December 1, 2014. For information on the compatibility with accessories marketed after this date, please contact Pixel's dealer for advice. PSM1401 V10.01 10
© Copyright 2024 ExpyDoc
