Driver Circuit Document - Categories On APW Company

CONNECTION
CONNECTION
SIGNAL
SIGNAL
DESCRIPTION
DESCRIPTION
J1 +
J1 +
PWR
PWR
This pin should be connected to the positive output of the driver power supply. The maximum voltage apThisshould
pin should
be connected
to the positive output of the driver power source. The maximum applied
plied
not exceed
+50 VDC.
voltage should not exceed +50 VDC.
This pin should be connected to the negative output of the driver power supply.
J1 -
GND
J1 J5 +
GND
CMD1
J4 +
J5 -
CMD1
GND
J6
J4 +-
CMD2
GND
The
command
for used
solenoid
#2return
shouldfor
beCMD1.
connected to this pin. This voltage must not exceed the voltage
This
pin may be
as the
applied to J1 +.
J6 +J6
GND
CMD2
J2 +
J6 -
PWR
GND
This
may be used
as the return
for IN2.be connected to this pin. This input is TTL / CMOS compatible.
Thepin
command
for solenoid
-2 should
However, this input must not exceed the voltage applied to J1 +.
This pin should be connected to one terminal of solenoid #1.
This pin may be used as the return for CMD2.
J2 J2 +
J3 +
SOL1
PWR
PWR
This pin should be connected to the other terminal of solenoid #1
This pin should be connected to one terminal of solenoid -1.
This pin should be connected to one terminal of solenoid # 2.
J2
J3 --
SOL1
SOL2
This
pin
should
connected
the
other terminal
This
pin
should
bebe
connected
toto
the
other
terminalofofsolenoid
solenoid # -1
2.
J3
J7 +
+
+ PWR
5 VDC
J3
J7 -
SOL2
GND
J7 +
+ 5 VDC
J7 -
GND
This pin should be connected to the negative output of the driver power source.
The command for solenoid #1 should be connected to this pin. This voltage must not exceed the voltage
applied to J1 +.
The command for solenoid –1 should be connected to this pin. This input is TTL / CMOS compatible.
This
pin maythis
be input
used as
thenot
return
for IN1.
However,
must
exceed
the voltage applied to J1 +.
shouldMaximum
be connected
to one
+5This
VDCpin
Output.
current
250 terminal
mAmps.
This pin
Return
forshould
+5 VDC.be connected to the other
of solenoid -2.
terminal of solenoid -2.
+5 VDC Output. Maximum usable current should be limited to 250 mAmps.
Return for +5 VDC.
Pick and Hold Module Pin Assignment and Description
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com
Warning:
Handling the Pick and Hold module shall be
performed in a static safe environment while a
ground strap is used. Damages arising due to
not observing the static pre
-cautions shall
void the limited ninety -day warranty.
User +5 VDC Output, Max. 250 mAmp
Return
Command -1
Command -1 Return
DC Power Source
Positive
Solenoid -1
+50 VDC Max
+9 VDC Min
Negative
EMD-01-TE-PH Wiring Diagram
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com
Warning:
Handling the Pick and Hold module shall be
performed in a static safe environment while a
ground strap is used. Damages arising due to
not observing the static pre
-cautions shall
void the limited ninety -day warranty.
User +5 VDC Output, Max. 250 mAmp
Return
Command -2
Command -2 Return
Command -1
Command -1 Return
Solenoid -2
DC Power Source
Positive
Solenoid -1
+50 VDC Max
+9 VDC Min
Negative
EMD-02-TE-PH Wiring Diagram
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com
Warning:
Handling the Pick and Hold module shall be
performed in a static safe environment while a
ground strap is used. Damages arising due to
not observing the static pre
-cautions shall
void the limited ninety -day warranty.
Command -2
Command -1
Solenoid -2
DC Power Source
Positive
Solenoid -1
+50 VDC Max
+9 VDC Min
Negative
Self Triggered Wiring Diagram
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com
R6 potentiometer adjusts the hold voltage. Using a
voltmeter, measure the voltage of JP2-3 (closer to
R6) respect to JP2-2
(middle pin), this is the output of R6 potentiomete r. The scale is 5% duty cycle per Volt. If it is se
t at 2 Volts, the hold voltage
will be 40% of the supply voltage.
R5 potentiometer adjusts the pick time. Using a vol tmeter, measure the voltage of JP2-1 (closer to R5)
respect to JP2-2 (middle
pin), this is the output of R5 potentiometer. The s cale is 400 mSecs per Volt. If it is set at 1.5 Vol
ts, the pick time will be 600
mSecs.
Limitation of Liability
APW Company / KG Squared LLC (APW) hardware and software are not intended for use in any
manner where human life or safety is at risk. APW products are not intended for life support equipment or work overhead.
In no event shall APW Company / KG Squared LLC be liable to any customer for costs or damages,
including lost profits, lost savings or other incidental or consequential damages arising out of the use
or inability to use such products even if APW Company / KG Squared LLC or an authorized APW
Company / KG Squared LLC representative has been advised of the possibility of such damages, or for
any claim by any other party. In any event, APW Company / KG Squared LLC liability arising in any manner in connection with the products, whether based in contract, product liability or tort, shall not exceed the purchase price of the product.
Limited Ninety -Day Warranty
APW Company / KG Squared LLC warrants to the original purchaser that this product to be free from
defects in material or workmanship for a period of ninety days from date of purchase. APW
Company / KG Squared agrees to repair any such defect or exchange the product with a new or equal
replacement. Defective product must be returned to APW Company /KG Squared LLC postpaid. This
warranty is void for any product that has been modified by the customer in any way. If failure of the
Product has resulted from accident, abuse, or miss
-application, APW Company / KG Squared LLC
shall have no responsibility under this Ninety -day Warranty.
APW Company
5 Astro Place STE B
Rockaway, NJ 07866
www.apwcompany.com

Download Report