ALD TEST Small.cdr

ALD
M EASU RI NG FOR RETROFIT
1.) SELECT EXISTI NG FIXTU RE TO M EASU RE
AN D OPEN ACCESS/GLASS DOOR PAN EL:
DIAM ETER”
2.) M EASU RE I NSIDE EDGE-TO-EDGE
DIM ENSIONS OF ACTUAL GLASS
( IF GLASS IS ROU N D, M EASU RE DIAM ETER):
LENGTH”
WIDTH”
3.) PROVIDE TH ESE LENGTH & WIDTH
DIM ENSIONS ON YOU R SIM PLYLEDS P.O. :
PG. 1
SIM PLYLEDS
3 3 1 3 B R O W N S T R E ET , G A R D E N C I T Y , I D 8 3 7 1 4
208.344.7533
M AT T H E W . D E R E N @ S I M P L Y L E D S . C O M
ALD
M EASU RI NG FOR RETROFIT
1.) SH UT OFF BREAKER AT PAN EL:
2.) REMOVE CONTENTS FROM FIXTU RE, I.E.,
GLASS, LAM PS, BALLAST, REFLECTOR, ETC.
(RECYCLE OR DISPOSE ACCORDI NG TO LOCAL CODE):
RETAI N CLIPS FOR
RE-USE I N STEP 3.
MOU NT DRIVER TO BOX
USI NG EXISTI NG TAPPED
HOLES & SECU RE WITH
PLUMBER’S TAPE
IF N ECESSARY
3.) I NSTALL TH E LED DRIVER I NSIDE BOX &
ALD U N IT I N PLACE OF GLASS:
PG. 2
SIM PLYLEDS
3 3 1 3 B R O W N S T R E ET , G A R D E N C I T Y , I D 8 3 7 1 4
208.344.7533
M AT T H E W . D E R E N @ S I M P L Y L E D S . C O M
ALD
M EASU RI NG FOR RETROFIT
WARNING
!
!
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
RISK OF FIRE OR ELECTRICAL SHOCK:
Ÿ Do not alter, relocate, or remove wiring, LED lamp holders, power supply, or
any other electrical component. Do not make or alter any open holes in an
enclosure of wiring or electrical components during kit installation.
Ÿ Installation of this retroﬁt assembly requires a person familiar with the
construction and operation of the luminaire’s electrical system and the
hazard involved. If not qualiﬁed, do not attempt installation. Contact a
qualiﬁed electrician.
Ÿ Unless otherwise indicated, do not make or alter any openings in the
compartment of wiring or electrical components during installation of this
retroﬁt assembly. Plug all unused openings in the compartment of wiring or
electrical components.
Ÿ To prevent wiring damage or abrasion, Do not expose wiring to edges of
sheet metal or other sharp objects.
Ÿ Luminaire’s wiring, power supply, or other electrical parts may be damaged
when drilling for installation of retroﬁt assembly hardware. Inspect wiring
and components for damage
Ÿ Replace with only SimplyLEDs driver, LEDs, or other parts as applicable.
Ÿ Do not use when enclosure is broken.
SimplyLEDs, Inc.
208.344.7533
SimplyLEDs.com
Copyright
2012, SimplyLEDs, Inc.
SIM PLYLEDS
3 3 1 3 B R O W N S T R E ET , G A R D E N C I T Y , I D 8 3 7 1 4
PG. 3
208.344.7533
M AT T H E W . D E R E N @ S I M P L Y L E D S . C O M

Download Report