EAS RF RECEIVER USER’S GUIDE EASY ACCESS SYSTEM BASED ON RADIO FREQUENCY DESCRIPTION AND USE TIPS Do not open the housing, it will be damaged and warranty will be void. Fasten the RECEIVER using the velcro strip. 3 Antenna wire 4 BLUE activation LED 4 3 BLUE LED switches on after push on TRANSMITTER BUTTON 5 that has been recorded. BLUE 42.3020-V1 RED LED flashes after push on TRANSMITTER BUTTON that has 10s ON RED RECORD ACTIVATION WITH DELAY ACTIVATION WITHOUT DELAY 0s 1 2 0.5s TOG PUL NO NC COM 12-24V AC/DC MODE 6 Record button for non-delayed activation 30s 7 Delay potentiometer YE WH GN RED LED RECORD not been recorded yet. POWER + + + + + BN 5 RED record LED BLUE LED ACTIVATION NC NO COM 12-24V AC/DC 1 Terminal block 8 Record button for delayed activation 2 1 2 DIP-switch ON 1 DIP 1 ON 2 DIP 2 TOGGLE 10s ON OFF 1 0,5s PULSE 2 8 7 6 Pushing the TRANSMITTER BUTTON once activates the output during 0.5 or 10s. The output is activated as long as the TRANSMITTER BUTTON is pushed. DIP 1 ON 1 DIP 2 ON TOGGLE 10s OFF PULSE 0,5s 2 Pushing the TRANSMITTER BUTTON once activates the output until you push the same button again. RECORDING / DELETING RECORDING RECORDING A TRANSMITTER BUTTON FOR NON-DELAYED ACTIVATION NO DELAY NO DELAY BUTTON RED ON OFF RED FLICKERS RECORDING A TRANSMITTER BUTTON FOR DELAYED ACTIVATION 0s + + DELAY DELAY BUTTON RED ON OFF RED FLICKERS 30s FACTORY VALUE: 0S TIP Adjust the activation delay AFTER all transmitters have been recorded. All transmitters recorded in a receiver have the same delay. DELETING ONE TRANSMITTER BUTTON + NO DELAY DELETING DELAY RED FLASHES PUSH SHORTLY SIMULTANEOUSLY DELETING ALL TRANSMITTERS 8sec + DELAY NO DELAY PUSH LONG SIMULTANEOUSLY RED FLASHES BLUE ON 1/2 1/4 TROUBLESHOOTING SYMPTOM The receiver does not react to the EAS RF transmitter. LED POSSIBLE CAUSES CORRECTIVE ACTION Check the transmitter LED and change the battery if necessary. The transmitter battery is down. Check the position of the antenna on the receiver. OFF The receiver power is off. Check the supply voltage. The transmitter has been used many times with one receiver and then with another one. Push the transmitter 2x. The transmitter is not recognized by the receiver. Execute the recording procedure described on page 1 with that transmitter. The receiver is not correctly wired. Check the connection to the door controller. The transmitter was recorded with an activation delay longer than desired. Check the delay potentiometer and adjust to the desired time. The transmitter was recorded with an activation delay. Delete the transmitter from the system and repeat the recording procedure without delay. The maximum number of recordable transmitters is reached. Try to reduce the number of transmitters or connect another receiver. The transmitter battery is down. Check the transmitter LED and change the battery if necessary. OFF OFF The receiver does not react to the EAS RF transmitter. RED 2x The door does not react to the EAS RF transmitter. The blue LED does not light up after pushing the transmitter button. BLUE OFF OFF It is impossible to record a transmitter. TECHNICAL SPECIFICATIONS Technology: radio frequency Transmitter frequency: 433 MHz Max. detection distance: 25m (open field) Power consumption: 30mA Supply voltage of receiver: 12 - 24V AC +/- 15%; 12 - 30V DC +/- 10% Receiver output: Relay with switch-over contact (free of potential) Max. voltage: 48V AC - 60V DC Max. current: 1A (resistive) 30W (DC) / 48VA (AC) Max. switching power: -10°C to 55°C Temperature range: Max. number of programmable transmitter buttons per receiver: 100 RED for button recording, BLUE for output activation LEDs: Specifications are subject to changes without prior notice EU declaration of conformity 42.7022 - V1 / 01.09 BEA hereby declares that the product EAS RF is in conformity with the basic requirements and the other relevant provisions of the standards 1999/5/EC and 2004/108/EEC. The complete declaration of conformity is available on our website: www.bea.be The colour version of this user's guide and other technical documentation are available on our website (www.bea.be) or can be requested by phone (+32 4 361 65 65) or mail ([email protected]). BEA SA - LIEGE Science Park - Allée des Noisetiers 5 - B-4031 Angleur - T +32 4 3616565 - F +32 4 3612858 - [email protected] - www.bea.be 2/2
© Copyright 2023 ExpyDoc
