LITE 4K - VolAmp Ltd.

®
LITE 4K
Camlinx Fibre systems are camera back systems for multiplexing broadcast quality video,
audio, talk-back and control signals onto fibre-optic cables for transmission between a
camera and a production facility. This gives greatly increased transmission distance
compared to coax cable, increased data rates, reduced cable thickness and reduced
susceptibility to EM interference. The Camlinx 4K system comprises of a Base unit which
resides in the production area and a camera-mounted Head unit. The units are connected
by a fibre optic cable which allows the transmission of 4K video signals up to 10Km. The
head unit can be powered down a hybrid fibre cable or with a local 12V supply.
®
LITE 4K
Camlinx 4K meets all SMPTE requirements for the transmission of Broadcast video.
Signals
Description
Connectors
4K VIDEO
4 x BNC
3 Gb/s
- SMPTE 424M Four 3G SDI signals in one direction from the
1.5 Gb/s - SMPTE 292M camera end to the base end. Support for 4K
270 Mb/s - SMPTE 259M SMPTE 425 video over 4 links.
HD VIDEO
2 x BNC
1.5 Gb/s - SMPTE 292M Two HD-SDI video signals. One in each
270 Mb/s - SMPTE 259M direction.
HDMI
1 x HDMI type A
The HD-SDI video output at the head or base is also output as HDMI.
SERIAL
2 x 9pin D(socket) Bidirectional serial signals for remote control panels (RCP).
RS232 or RS422 – user selectable.
TALLY
1 x 9pin D(plug)
Bidirectional Tally signal can be asserted at head or base. (9pin D plug)
SYNC
1 x BNC
Bi-level(SD) and Tri-level(HD) syncs are supported.
Signals in both directions, the sync/genlock signal can be sourced from
either end. The system will detect the sync signal and automatically
configure the system to support it.
ETHERNET 1 x RJ45
10/100 baseT (Bidirectional).
Provides support for Ethernet based RCPs or web browser.
TIMECODE 2 x BNC
Two Timecode signals, one in each direction.
TALKBACK 2 x XLR5
/AUDIO
Noise : better than
-70dB
2 bidirectional high quality audio channels
suitable for programme audio or Talkback.
Additional audio channels can be added with
the ASM. (Audio to Serial Module)
(5 XLR to 3 XLR conversion lead available.)
Gain : +6dB
increments
(adjusted via user
interface)
Phantom Power :
(enabled via user
interface)
+24V
Audio input signals to the Camlinx Lite 4K
system are not embedded onto the audio.
They pass separately through the system.
Power
Head
Unit
Input Voltage range : 8 – 14VDC
Power consumption : 12W max.
Options
1) +12V input power connector on the head.
2) +12V derived from +48V in hybrid cable.
(Head unit has built in 12V power supply )
3) Battery (user specified)
4) +12V power output socket available on head to power
other equipment up to a max. of 50W (approx.)
Base
Unit
Input Voltage range : 220 – 240VAC
Power consumption : 12W max
Fibre Only Cable
2 x fibres, Single Mode, 9um wavelength
Transmission distance : >10km
Hybrid Fibre
2 x fibres, 4 x copper power conductors, Single Mode, 9um wavelength
Transmission distance : 100m (reduced distance due to power losses down cable)
Connectors
Neutrik Opticalcon, LEMO, other
(user specify)
®
LITE 4K
Mechanical
Dimensions (mm)
Head (L x W x D) : 144 x 183 x 41 (without power module)
Base (L x W x D) : 435 x 45 x 165 (standard 1U )
Weight (g)
Head (including power module) : 1000
Base : 2000
Temp. Range
-20 to +55°C
Ordering Information - Camlinx Lite 4K system
CAML4KH-(C)-(P)-(A)
Full 4K system, Head unit powered over
hybrid cable. System includes;
1. Camlinx Lite 4K Head unit with PSU
2. Camlinx Lite 4K Base unit in 1U enclosure
3. PSU-52V (provides 52VDC for
transmission down the hybrid fibre cable)
4. Fibre Adaptor Box (FAB).
CAML4K-(C)-(P)-(A)
Full 4K system, Head unit powered locally.
System includes;
1. Camlinx Lite 4K Head unit, no PSU .
2. +12V mains adaptor for Head unit.
3. Camlinx Lite 4K Base unit in 1U enclosure
4. Fibre Adaptor Box (FAB)
Other configurations available : contact factory
Fibre cable not included.
Options;
(C) – connector
Select : N – Neutrik Opticalcon
L3K – LEMO 3K
LH - LEMO Hermaphroditic
(P) – Battery mounting plate
Select : AB – Anton Bauer
V - V-Lok
P - PAG Lock
(A) – add this field to include
additional audio channel with the
Audio to Serial Module (ASM).
[email protected]
Contact Information:
Camlinx systems are manufactured by Volamp Ltd., Unit 3, Riverside Business Park,
Dogflud Way, Farnham, Surrey GU9 7SS. UK
Email : [email protected]
Tel : +44 (0)1252 724055
www.volamp.com

Download Report