Tender texts Calio S BMS Document number 1157.524/01-EN Lfd. Nr. Stückzahl Gegenstand KSB Calio S BMS 25-60 Maintenance-free, screw-ended high-efficiency glandless pump with electric motor and integrated continuously variable differential pressure control, an energy efficiency index which exceeds the ErP 2015 requirements, and a two-piece thermal insulation included in the scope of supply as a standard. Fluids handled - Heating water to VDI 2035 - Pure, thin-bodied, non-aggressive and non-explosive fluids not containing any mineral oil, solids or long fibres - Fluids with a maximum viscosity of 10 mm2/s - Water/glycol mixtures - Ethylene/propylene glycols with corrosion inhibitors as per operating manual Operating modes - Constant-pressure control - Proportional-pressure control - Eco Mode with dynamic differential pressure setpoint adjustment - Open-loop control with fixed speed levels Functions - Operating mode set manually - Setpoint for differential pressure (closed loop control) or speed (open loop control) set manually or via external 0-10 VDC analog signal - Control panel with integrated symbols, showing the operating mode and, in alternation, the electrical input power and the flow rate - Error codes indicated on the display - Automatic setback operation, can be disabled - Automatic venting - Soft start with limitation of starting current - Unlocking function - Motor protection Communication interfaces and functions integrated in the pump - 1x terminal pair for external 0-10 VDC analog signal - 1x terminal pair for external ON/OFF of the pump - 1x general fault message relay (change-over contact) Design : Single system 1 x 100 % Driver Speed Selection : Specified speed Pump Speed adjustment via. : Frequency inverter Technical data Medium Allowed media temperature allowed ambient temperature: Allowed humidity Max. Flow Max. pump head Pressure rating Connection pump Connection pipe Length Supply voltage Electrical power P1 Electrical current …………………... -10°C bis +110°C 0°C bis +40°C ≤ 80% 8,5 m3/h 6,0 mWS PN6/10 G1½“ R1“ 180 mm 1~230 V ± 10% bei 50/60 Hz 8 – 100 W 0,11 – 0,90 A Preis je Einheit Betrag Tender texts Calio S BMS Document number 1157.524/01-EN Noise pressure level Material housing Material can Material impeller Material shaft Protection Weight (net) < 45 dB(A) GG (EN-GJL-200) with cathodic electrocoating stainless steel 1.4301 stainless steel 1.4301 stainless steel 1.4034 IP 44 3,9 kg Make Type Material number KSB Calio S 25-60 BMS 29 134 307 Tender texts Calio S BMS Document number 1157.524/01-EN Stückzahl Gegenstand Preis je Einheit Betrag KSB Calio S BMS 30-60 Maintenance-free, screw-ended high-efficiency glandless pump with electric motor and integrated continuously variable differential pressure control, an energy efficiency index which exceeds the ErP 2015 requirements, and a two-piece thermal insulation included in the scope of supply as a standard. Fluids handled - Heating water to VDI 2035 - Pure, thin-bodied, non-aggressive and non-explosive fluids not containing any mineral oil, solids or long fibres - Fluids with a maximum viscosity of 10 mm2/s - Water/glycol mixtures - Ethylene/propylene glycols with corrosion inhibitors as per operating manual Functions - Operating mode set manually - Setpoint for differential pressure (closed loop control) or speed (open loop control) set manually or via external 0-10 VDC analog signal - Control panel with integrated symbols, showing the operating mode and, in alternation, the electrical input power and the flow rate - Error codes indicated on the display - Automatic setback operation, can be disabled - Automatic venting - Soft start with limitation of starting current - Unlocking function - Motor protection Communication interfaces and functions integrated in the pump - 1x terminal pair for external 0-10 VDC analog signal - 1x terminal pair for external ON/OFF of the pump - 1x general fault message relay (change-over contact) Design : Single system 1 x 100 % Driver Speed Selection : Specified speed Pump Speed adjustment via. : Frequency inverter Technical data Medium Allowed media temperature allowed ambient temperature: Allowed humidity Max. Flow Max. pump head Pressure rating Connection pump Connection pipe Length Supply voltage Electrical power P1 Electrical current …………………... -10°C bis +110°C 0°C bis +40°C ≤ 80% 8,5 m3/h 6,0 mWS PN6/10 G1½“ R1“ 180 mm 1~230 V ± 10% bei 50/60 Hz 8 – 100 W 0,11 – 0,90 A Subject to technical modifications. Operating modes - Constant-pressure control - Proportional-pressure control - Eco Mode with dynamic differential pressure setpoint adjustment - Open-loop control with 10 speed levels 1157.524/01-EN / 20.08.2014 lfd. Nr. Tender texts Calio S BMS Document number 1157.524/01-EN Noise pressure level Material housing Material can Material impeller Material shaft Protection Weight (net) < 45 dB(A) GG (EN-GJL-200) with cathodic electrocoating stainless steel 1.4301 stainless steel 1.4301 stainless steel 1.4034 IP 44 3,9 kg Make Type Material number KSB Calio S 30-60 BMS 29 134 308
© Copyright 2024 ExpyDoc
