Sumbersible 200-350 mm Brochure

Product Introduction
3300.12 / 2 - 85 G3
Submersible Motor Pumps
Application
200 mm to 350 mm
For pumping of clean, cold water, non corrosive and non
abrasive to the pumpset material, irrigation, urban & rural
drinking water supply, pressure boosting, air-conditioning
systems, industrial plants, cooling water systems, fountains,
sea water desalination works, mine dewatering etc.
Design
Submersible pumpset is a compact unit made up of a
submersible pump & a submersible motor with shafts
connected by a sleeve and operates beneath the surface of
water. This maintenance-free pumpset is suspended vertically
from raising main when installed.
Submersible Pumps are single or multistage centrifugual
pumps with radial or mixed flow impellers. The casings of the
radial flow impeller pumps are clamped together by flat steel
hook bolts, whereas that of mixed flow impeller pumps by
studs.
Between the pump & the motor is the suction casing. A nonreturn valve is in-built and fitted at the pump discharge end.
Submersible motors are water filled, water lubricated squirrel
cage type. The axial thrust generated by the pump is absorbed
by a thrust bearing fitted at the bottom of the motor. The
diaphragm below the thrust bearing compensates the overpressure which arises as a result of the thermal expansion of
the water filled, when the temperature of the winding rises.
3 phase submersible motors are available up to 110 kW, 2 pole,
and voltage 380 to 420 V, 50 Hz. Motors for other voltages & 60
Hz. can be supplied on request.
Bearings : The pump is provided with radial bearings. The
motor has radial as well as axial thrust bearings. All the
bearings are water lubricated and protected to a large degree
against the ingress of sand of by suitable structural elements.
Shaft seal : The motor is sealed by radial seal rings to avoid
mixing of well water and the fill water. Mechanical seals can be
provided on request.
Discharge connection : Threaded non-return valve is fitted at
discharge end of the pumpset having sizes form G3" to G8" ( 75
to 200 mm).
Operating data
Capacity
Total head
Motor rating
Speed
Frequency
Supply voltage
Up to 900 m3 / hr.
Up to 300 mtrs.
Up to 110 kW
2900 rpm
50 Hz
Up to 420 volts
Designation
Pump
U
P
H
293
/
C
20
10
Type of Impeller
(U= Radial flow)
(B= Mixed flow)
Complementary letter
Min. borehole dia. in inches
(H= 8", N= 10", T= 12", V=14")
Hydraulic reference no.
No. of stages
Motor
Min. bore hole dia. in inches
Motor ref. no.
Construction variant
Power in HP
No. of phases
H
B
3
Family Curves : 50 Hz - 2900 rpm
400
BPN 374
BPN 394
300
1000
800
200
600
BPN 425
400
BQTs 466
100
80
BPVs 525
H
(m)
200
BST 435
BPN 393
BPH 373
BPH 384
40
BPH 333
UPH 293
60
H (ft)
100
80
20
60
40
8
20
6
30
7
8
40
10
50
12
60
14 16 18 20
80
100
Q (l / s)
120
30
Radial flow pump
Description
106
108
143
171
211
232
355
75-9
752
756
759
Suction casing
Stage casing
Suction strainer
Diffuser
Pump shaft
Impeller
Discharge brg. body
Valve body
Valve seat
Valve spring
Valve dish
60
100
600
140
800
200
1000
240
Material
Part
C.I.
C.I.
M.S. Gal.
Bronze**
Cr.St.
Bronze
C.I.
C.I.
C.I.
Spr. St.
C.I.
106
112
143
211
232
502
75-9
752
756
759
Description
Suction casing
Stage bowl
Suction strainer
Pump shaft
Impeller
Wearing ring
Valve body
Valve seat
Valve spring
Valve dish
Material
C.I.
C.I.
M.S. Gal
Cr.St.
Bronze
Bronze
C.I.
C.I.
Spr. Steel
C.I.
Motor : 250 mm
Description
Material
Part
145
160
271
354
382
384
387
388
392
421
545
81-59
818
823
849
Adaptor
Cover
Sand guard
Thrust brg. housing
Bearing body
Thrust brg. plate
Thrust brg. segments
Counter th. brg. plate
Brg. segment carrier
Oil seal
Bearing bush
Stator
Rotor
Diaphragm
Coupling sleeve
C.I.
C.I.
Bronze
C.I.
C.I.
Carbon*
Cr. St.*
Bronze
C.I.
St. / Rubber
Bronze
Steel
Steel
Rubber
Cr. St.
384
387
Thrust brg. plate
Thrust brg. segments
Bz. / FerroAsb.
Bronze@
* Up to 41 HP
60
400
Mix flow pump
Motor : 200 mm
Part
200
300
Q (m3 / hr)
40
Material of construction
Part
160
@ Above 41 HP
@
145
160
271
354
382
384
387
388
392
421
545
81-59
818
823
849
Description
Adaptor
Cover
Sand guard
Thrust brg. housing
Bearing body
Thrust brg. plate
Thrust brg. segments
Counter th. brg. plate
Brg. segment carrier
Oil seal
Bearing bush
Stator
Rotor
Diaphragm
Coupling sleeve
Material
C.I.
C.I.
Bronze
C.I.
C.I.
Bz / Ferro Asb.
Bronze
Bronze
C.I.
St. / Rubber
Bronze
Steel
Steel
Rubber
Cr. St.
Note : For motors of 250 mm upto 85 HP the oil seal is in the pump.
Above 85 HP it is in the motor.
** UPHA - Integral C.I. Diffuser
Submersible Motor Pumps
Sectional drawing & list of components
Radial Flow
75-9
756
759
752
355
112
108
171
232
211
143
106
849
271
421
145
382
545
818
81-59
382
545
388
384
387
354
392
823
160
Mix Flow
Submersible Motor Pumps
Deep Well Installation
6
3
4
7
5
2
1
2
3
4
5
6
7
Hh
Ht
He
T
1
Submersible pumpset
Riser pipe
Support clamps
Control Valve
Cable
Pressure gauge
Starter
Legend:
T = Depth of well
He = Installation depth
Hh = Stationary water level
Ht = Lowest water level
Note:
He-Ht = at least 0.5m
It must be ensured that the unit is freely suspended from the
riser pipe and does not touch the bottom of the sump !
KSB PUMPS LIMITED
Works :
Pimpri
Chinchwad
Coimbatore
Sinnar
Vambori
- Irrigation and Process Division, Mumbai-Pune Road, Pune - 411 018.
- Power Projects Division, D - II Block, MIDC, Pune - 411 019.
- Valves Division, 151, NSN Palayam Post, Mettupalayam Road - 641 031.
- Water Pumps Division, Plot No E-3 & E-4, MIDC Sinnar, Malegaon, Dist. Nashik- 422 113.
- Foundry Division, Ahmednagar - 413 704.
Telephone No.
(020) 2710 1000
(020) 2740 9100
(0422) 246 8222
(02551) 230252 / 53 / 55 / 56
(02426) 272534, 272528, 272074
Fax
(020) 2742 6000
(020) 2747 0890
(0422) 246 8232
(02551) 230254
(02426) 272043
Regd. Office :
Mumbai
- 126, Maker Chambers III, Nariman Point - 400 021.
(022) 6658 8787
(022) 6658 8788
Zonal Offices :
Chennai
Kolkata
Mumbai
NOIDA
-
(044) 2235 2571-2, 2235 5673
(033) 2287 0473, 2290 0117
(022) 6658 8787
(0120) 254 1091-93, 254 1501-3
(044) 2235 2749
(033) 2287 0588
(022) 6658 8788
(0120) 255 0567
Guindy House, 2nd Floor, 95, Anna Salai - 600 032.
30, Circus Avenue, 2nd Floor - 700 017.
126, Maker Chambers III, Nariman Point - 400 021
"KSB House", A-96, Sector IV, NOIDA 201 301, Dist. Gautam Budh Nagar, U. P.
Branch Offices :
• Ahmedabad - (079) 26579610 / 11 • Aurangabad - (0240) 2351440, 2342447 • Bangalore - (080) 23491806, 23493925 • Baroda - (0265) 2330532, 2333226
• Bhubaneswar - (0674) 2558497, 2553061 • Chandigarh - (0172) 2640771, 2652121 • Hubli - (0836) 2232244 • Indore - (0731) 2529478 • Jaipur - (0141) 2224554, 2224904
• Jamshedpur - (0657) 2317129, 2317130 • Lucknow - (0522) 2635203, 2635597 • Nagpur - (0712) 2236889 • Pune - (020) 25431258 / 59 / 60 • Raipur - (0771) 4062556, 2583921
• Secunderabad - (040) 27001724, 27003696
Service Stations :
Odhav
NOIDA
Howrah
Chennai
-
Shed 22, G.V.M. Estate, Ahmedabad - 382 410.
"KSB House" A- 96, Sector IV, 201 301.
142/1, Foreshore Road, Near Ramkrishnapur Launchghat - 711 101.
No. 4 (old no. 18) Chakrapani Road, Guindy, 600 032.
(079) 22900372
(0120) 2541091-93
(033) 26382909
(044) 22550704
Mktg. Serv./12-11/2000
Technical matter. Subject to change without notice.
Manufactured in technical collaboration with KSB Aktiengesellschaft., Germany by :

Download Report