K14517 6/07 Rev. A
DCID-EXT
Dialer Capture Intelligence Device
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The Honeywell DCID-EXT Dialer Capture Intelligence
Device (referred to as the DCID-EXT) is intended for
control panels that DO NOT support the Honeywell
ECP bus and therefore are not capable of communicating with Honeywell AlarmNet communication
devices over an ECP bus. Additionally it is for
instances where NO PHONE LINE SERVICE is used
for reporting.
INSTALLATION
Notes:
•
Ensure the power source complies with the
specified input voltage for this device. The power
source must utilize a battery backup.
•
When used with control panels where no wired
zones are available (for wiring the output
TRIGGER signal to), mount the DCID-EXT inside
the control panel.
This DCID-EXT can be mounted external to, or inside
the control panel’s cabinet.
•
When used with control panels that have an available wired zone (for wiring the output TRIGGER
signal to), the DCID-EXT may be mounted inside
the control panel or mounted externally.
•
The DCID-EXT will report certain trouble
conditions by activating the Trigger signal sent to
the control panel. An active Trigger signal will be
set when any of the following conditions occur:
The DCID-EXT Dialer Capture Intelligence Device
captures Contact ID messages from a control panel’s
phone line and sends them to a Honeywell ECP bus
AlarmNet communications device (e.g., 7845GSM),
which then communicates those messages to the central
station over the GSM network or internet.
OPERATION
When an event occurs, the control panel goes off hook to
dial the central station. The DCID-EXT detects the offhook condition and provides the control panel with a
dial tone. When the control panel detects the dial tone,
it begins dialing the central station. After the phone
number is completed, the DCID-EXT returns a
handshake to the control panel.
The control panel then sends the reports to the DCIDEXT, which in turn sends them over the ECP bus to the
AlarmNet communications device. The DCID-EXT
kisses off each report received successfully from the
control panel. The communications device then
transmits the messages to the central station (either
over the GSM network, or the internet, as applicable).
When all the reports are sent, the DCID-EXT goes off
hook.
DCID-EXT
Summary of Connections label
SPECIFICATIONS
Physical: 6-1/2” H x 4-1/4” W x 1-1/4” D
(165mm x 110mm x 32mm)
Electrical:
Input Voltage: 12VDC nominal (9-14VDC, from
control panel)
Input Current: 40mA standby / 80mA active
The built-in tamper switch detects the cover
being removed.
♦
An AlarmNet communications device fault
occurs.
The above condition will be reported if the output
trigger is wired to an available zone and the red
power wire to the DCID-EXT is intact. To ensure
the security of the red power wire, mount the
DCID-EXT in the control panel.
External Horizontal Wall Mounting:
For horizontal mounting, two slotted holes are used.
1.
2.
3.
PACKAGE CONTENTS
The following items are included:
•
•
♦
Measure and transfer the position of the two
horizontal mounting holes to the desired mounting
area.
Drill 3/16 inch holes for drywall, or 7/32 inch holes
for plaster. Tap in plastic wall anchors.
Insert self-tapping screws into the wall anchors
leaving the heads projecting 1/8”. Hang the DCIDEXT on the screw heads via two of the slotted holes
on the module back.
External Vertical Wall Mounting:
For vertical mounting, one slotted hole and one open
hole are used. The circuit card must be removed for
access to the open hole.
1.
2.
3.
4.
Measure and transfer the position of the two
vertical mounting holes to the desired mounting
area.
Drill 3/16 inch holes for drywall, or 7/32 inch holes
for plaster. Tap in plastic wall anchors.
Insert a self-tapping screw into the wall anchor for
the slotted hole leaving the head projecting 1/8”.
Remove the enclosure cover by gently prying the
cover off.
5.
6.
7.
phone line voltage. When the radio becomes
initialized, normal operation will resume.
Remove the circuit board by squeezing the two
internal plastic retention tabs, while gently pulling
the circuit card.
Hang the DCID-EXT enclosure on the screw, then
insert the second screw through the enclosure back
into the open hole.
Orient the circuit board edge in the enclosure
starting with the side opposite the two plastic
retention tabs. When the circuit board edge is
properly seated, push to snap the opposite end of
the board into place.
Internal Control Panel Mounting:
When mounting inside of control panels, the mounting
method must be determined by the installer depending
on the particular control panel. If raised tabbed holes
are available, please use them. For those panels where
raised tab holes are not available, then a sufficient
amount of double stick foam tape (installer supplied) or
other suitable method should be used.
It is important to locate the DCID-EXT within the
control panel so that its cover can easily be removed for
testing and service.
CONNECTIONS
1. If the enclosure cover is on, remove by gently
prying the cover off.
2. Connect the wires as shown in the DCID-EXT
Dialer Capture Intelligence Device Connections
diagram.
3. Affix the supplied Summary of Connections label to
the inside of the enclosure cover.
4. Replace the enclosure cover by snapping back in
place.
Pulse dialing is not supported and must be disabled
in the control panel.
Since this product does not communicate through a
PABX, do not program the PABX fields.
To ensure the maximum amount of messages can
be transmitted to the central station before a com
failure occurs, ensure the control panel is programmed with a primary and secondary central
station number.
Ensure the control panel is programmed for the
maximum number of retry attempts.
This product only supports one-way communications (from the control panel to the central station).
For those control panels that support two-way voice
communications, speakerphone, paging, follow-me,
etc., these features will no longer be available. The
control panel must be programmed for one-way
communications only.
Since this product only supports one-way communications (from the control panel to the central station), the Honeywell Compass Downloader cannot
be used.
In the event this product loses power (such as from
a cut wire) it would not be able to generate a fault
trigger to the control panel and set an alarm. In
this case, after the panel has exhausted its redial
attempts, a com failure will be displayed by the
panel (you may have to scroll through the
messages).
If the DCID-EXT senses a fault, it will send a
Trigger signal to the control panel zone (if wired to
a zone). At this point the DCID-EXT will also drop
the phone line voltage and will not provide a dial
tone to the control panel. During this time, the
control panel will make retry attempts (8 for
residential, and more for commercial) to dial out
and send a report. Until the control panel has
completed the series of retry attempts it will not be
able to detect a Telco fault.
INSTALLATION AND CONFIGURATION NOTES
Please read each configuration note and implement the
appropriate ones for the installation. Mark each
“Check Box” to ensure the notes are understood and
implemented as necessary.
The AlarmNet communications device must be
configured as device 3 on the ECP bus. Ensure
other devices do not conflict with this address.
The subscriber ID sent to the central station will be
the one programmed into the AlarmNet communications device, not the one in the control
panel.
This product supports 4-digit account code Contact
IDs.
Since control panel messages are now routed
through the DCID-EXT to the central station, the
message confirmation kissoff signal sent back to
the control panel ONLY confirms the DCID-EXT
received the message. Under certain communication conditions it is possible that the control
panel message was not received by the central
station.
When the DCID-EXT is first powered up and does
not detect an initialized radio within 5 minutes, it
will generate a fault to the control panel.
Additionally the control panel will not receive
To minimize the wait time, for control panels that
allow setting the Telco Fault detection time, please
set it to the minimum detection time.
2
For control panels that may generate erroneous
Telco fault conditions based on grounding (such as
the VISTA-15), at the control panel turn off "Telco
Fault" monitoring.
If an AlarmNet communications device fault is
detected, this will be reported to the control panel
as a com failure. If Telco fault is turned on, an
AlarmNet failure will be displayed as a Telco Fault.
If the DCID-EXT trigger is wired to a zone, the
DCID-EXT will trigger the control panel to alarm
this zone and display a message. With some
control panels, displayed alarm messages for
triggered zones may hide a "com failure" message.
The com failure message can be displayed by first
clearing the zone alarm message(s).
DCID-EXT, keypads and AlarmNet
communications device will be reset.
If the DCID-EXT, keypads, and the AlarmNet
communications device are powered from the
control panel’s aux power (that is reset for a fire
alarm reset), and a fire alarm reset occurs, the
This device is not compatible with the Apex Destiny
6100 control panel.
DCID-EXT DIALER CAPTURE INTELLIGENCE DEVICE CONNECTIONS
NOTES:
1.THE TRIGGER SIGNAL MUST BE WIRED TO A CONTROL PANEL
24 HOUR ZONE. DO NOT WIRE TRIGGER TO A 2-WIRE SMOKE
DETECTOR ZONE.
DCID-EXT
STATUS LEDs
INDICATION
STATUS
GREEN - STEADY ON
POWER ON
GREEN - FLASHING
RED - STEADY ON
POWER ON, AND ECP ACTIVITY
OFF HOOK, AND BUFFER FULL
RED - FLASHING
TELCO ACTIVITY
2. WIRE THE EOLR ACROSS THE DCID-EXT TRIGGER AND GND
TERMINALS TO ENSURE CABLE SUPERVISION.
3. LENGTH OF CABLE TO ALARMNET COMMUNICATIONS DEVICE
SHALL NOT EXCEED 50 FEET.
TB
RING
ELECTRICAL SPECIFICATIONS:
TIP
EOLR
VOLTAGE: 12VDC NOMINAL
(9-15VDC, FROM
CONTROL PANEL)
CURRENT: 40MA STANDBY /
80MA ACTIVE
CONTROL PANEL
RING (RED)
INCOMING PHONE LINE
TIP (GRN)
BLK
GND
AUX PWR GROUND
RED
+12 VDC AUX PWR
TRIGGER (HIGH
SIDE OF ZONE)
AUX PWR
TRIG
ZONE
TB (ECP BUS)
YEL
STATUS
LEDs
NOT USED
DATA OUT
DATA IN
GRN
DATA IN
DATA OUT
RED
V+
V+
BLK
GND
GND
RJ-45
JACK
USE RJ-45
CABLE ONLY
COVER TAMPER
SWITCH (REED)
NOTE:
IF A SEPARATE AUX POWER
SUPPLY IS USED, ENSURE IT
UTILIZES A BATTERY BACKUP, AND ITS GROUND IS CONNECTED TO THE CONTROL
PANEL AUX POWER SUPPLY
GROUND.
ALARMNET COMMUNICATIONS
DEVICE
ALTERNATE CONNECTION
TO CONTROL PANEL
INCOMING PHONE LINE
(TIP-GRN, RING-RED)
DCID-EXT-SOC-V0
DCID-EXT Interface Terminal
Function
Destination
Ring
(Typically Red or Yellow)
Telco Ring signal.
Control Panel incoming phone line Ring
terminal.
Tip
(Typically Green or Black)
Telco Tip signal.
Control Panel incoming phone line Tip
terminal.
Black
Circuit ground.
Control Panel Aux Pwr Out – (GND)
Red
Circuit power.
12VDC nominal (9-15VDC) with battery backup.
Control Panel Aux Pwr Out + (12VDC)
Trig
(Orange)
Fault output. The Trigger signal is an open collector
signal that is active closed. This signal must be wired
to a control panel 24 hour zone.
Control Panel zone terminal.
Yellow
ECP bus Data Out.
AlarmNet communication device ECP
data in.
Green
ECP bus Data In.
AlarmNet communication device ECP
data out.
Red
ECP bus V + In.
AlarmNet communication device
+12VDC in.
Black
Circuit ground.
AlarmNet communication device GND.
RJ-45 Jack
This is used as an alternate connection for those
installations where a RJ-45 cable is a more
convenient interface to the control panel.
Control Panel RJ-45 jack, or incoming
phone line terminals.
3
REFER TO THE CONTROL PANEL INSTALLATION INSTRUCTIONS
FOR DETAILS REGARDING THE ENTIRE ALARM SYSTEM.
LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 2 Corporate Center
Drive, Melville, New York 11747, warrants its product(s) to be in conformance with its own plans and specifications and
to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp
control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of original
purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall
apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any
product(s) which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship
under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product(s)
is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Connection of any device(s)
to a communicating bus of a Honeywell security system (e.g., keypad bus, polling loop) other than those manufactured or
approved by Honeywell shall void this warranty. For warranty service, return product(s) transportation prepaid, to
Honeywell Factory Service, 2 Corporate Center Drive, Melville, New York 11747.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER
BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN
NEGLIGENCE OR FAULT.
Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will
prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all
cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm
system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it
is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a
result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING.
HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE
ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH
SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.
This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase
or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.
2 Corporate Center Drive, Melville, NY 11747
Copyright 2007 Honeywell International Inc.
www.honeywell.com/security
ÊK14517AŠ
K14517 6/07 Rev. A
© Copyright 2024 ExpyDoc
