SBLL250 561132 SBLL500 561134 SBLL800 561136 Power

INSTRUCTION SHEET
SBLL250 / SBLL500 / SBLL800
561132 / 561134 / 561136
®
•
•
®
UL 1059
IEC60947-7-1
1000V AC/DC
Short-Circuit Current Rated
100kA @ 600V
Ui: 1000V AC / 1500V DC
Uimp: 12kV
561132 : SBLL250
UL: 255 AMP - SCCR rated for up to 100kA* / IEC: 290 AMP - Icw 14.4kA rms - Ipk up to 42kAª
mm
35
n
i
1.4
8AWG - 250 kcmil
[10 - 120 mm² ]
7/16" 10.5
 221 in-lbs [ 25Nm ]
mm
18
in
0.7
20-24mm¹
7/16" 10.5mm
0.25in 6
MAX
1.1in 27 MAX
561134 : SBLL500
UL: 475 AMP - SCCR rated for up to 100kA¹ / IEC: 750 AMP - Icw 36kA rms - Ipk 51kA
n
.4i
mm
35
1
7/16" 10.5
n
.7i
6AWG - 700kcmil
[ 16-400mm² ]
m
8m
1
0
20-50mm¹
 265 in-lbs [ 30Nm ]
7/16" - 5/8"
[10.5mm - 16.5mm]
0.39in 10mm
MAX
2.0in 50 MAX
561136 : SBLL800
UL: 800 AMP - SCCR rated for up to 100kA* / IEC: 1250 AMP - Icw 57.6kA rms - Ipk 75kA
n
i
1.4
mm
2 X 4AWG - 500 kcmil
[2 X 25 - 300 mm² ]
35
7/16" 10.5
in
0.7
7/16" 10.5mm
mm
18
20-40mm¹
 265 in-lbs [ 30Nm ]
in
1.4
0.31in 8mm
MAX
n
.7i
mm
35
1.57in 40mm MAX
mm
7/16" 10.5mm
18
0
50-80mm¹
1.6in 40mm
0.31in 8mm
MAX
NOTES:
1.
* SEE UL FILE E198301 FOR UL1059SA SHORT CIRCUIT CURRENT RATING CONDITIONS
2.
ª SBLL250: WHEN NOT MOUNTED USING DIN RAIL:
A. For IEC short circuit rating of 42kA Ipk a SBLEC must be used on both ends and between each block in a set.
B. For IEC short circuit rating of 20kA Ipk, up to three terminal blocks can be mounted between SBLEC end stops.
WARNING:
1. ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at www.erico.com and from your ERICO customer service representative.
2. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property damage, serious bodily injury and death.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
UL is a registered trademark of UL LLC.
cURus is a registered certification mark of UL LLC.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corperation.
TECHNICAL SUPPORT:
www.erico.com
IP8062_G
1 of 2
© 2009, 2010, 2014 ERICO International Corporation.
INSTRUCTION SHEET
Easy Side-by-Side attachment
90°
Clips lock in the out position for easier
installation and removal
*MUST BE PUSHED IN WHEN INSTALLED ON DIN PROFILE
561138 : SBLEC - END STOP
LOCKING SET SCREW
5 in-lbs [ 0.56 Nm]
1/16"
1.5MM
0in
3.4
mm
86
1.25in 32mm
0.75in 19mm
2.75in 70mm
Used to mount SBLL250
blocks dirrectly to a panel.
Prevents sliding
on DIN profile
561132
561134
2.05in 52mm
0.45in 11mm
561136
3.35in 85.1mm
4.53in 115.1mm
2.60in 66.0mm
3.78in 96.0mm
0.30in 8mm
0.45in 11mm
4.25in 108mm
8.10in 206mm
1/4" [M6]
30 IN-LBS [3.5N-m]
NOTE:
1. For multiple phase assemblies, join blocks together before installing on DIN profile
2. When mounted on DIN profile end stops must be used on both ends of a set of blocks.
3. IEC short circuit applications require the cable to be secured within 0.2m of the terminal block.
IP8062_G
2 of 2
© 2009, 2010, 2014 ERICO International Corporation.
0.30in 8mm

Download Report