Oilfield - L.V. Lomas

Oilfield
LIMITED / LIMITÉE
lvlomas.com
Cementing
PRODUCT
TRADENAME
Alumino Silicate
E-Spheres SLG
Lightweight material used in well cementing to reduce cement
slurry density.
Highly Reactive Metakaolin
PowderPozz- Regular
Oil Well cement extender. Metakaolin is a highly reactive
pozzolanic material produced by the controlled activation of
selected clays. Metakaolins are used in oil well cementing to
improve the compressive and flexural strength of the hardened
cement. The metakaolin also reduce the hardened cement
permeability to liquids and gases.
Magnesium Alumino Silicate
Acti-Gel 208
High efficiency suspension/anti-settling mineral. Imparts
no change to viscosity of cement systems. Is not pH or
temperature sensitive. Is a compact, low dusting with free
flow characteristics. Performs in high slump and zero slump
concrete mixes. Ensures excellent distribution of aggregates in
Concrete and contributes to integrity.
Perlite
Harborlite
Lightweight minerals used in well cementing to reduce cement
slurry density.
Drilling
PRODUCT
TRADENAME
Cationic Polyacrylic Polymers
Performol LP & LWP
Synthetic Shale Control Inhibitor.
Citric acid
Citric acid Anhydrous Fine
granular, non edible
pH reducer and scale remover in water based drilling fluids. Iron
control, scale removal, prevents precipitation of metal oxides.
Diatomite/ Diatomaceous
Earth
Celite
LCM, Oil well Cementing, Filtration. Diatomite can be used
as a loss circulation material in drilling fluids to form a rapid
dewatering plug and block loss of fluid. Also used as a filtration
material, in diatomite filter units, to remove solids from
completion and work-over fluids. Diatomite is used in oil well
cementing as an extender and as a pozzolanic additive to
reduce the permeability of the hardened cement to liquid and
gases.
Environmentally Friendly
Lubricant
TNB 100N
Lubricant excellent for stuck coil or drillstring in drilling
formations and stage plugs. TBN 100N can be spotted to
improve sliding, relieve stuck plugs and shale stabilization and
corrosion inhibition are extra benefits. Mixes instantaneously in
water and can be added directly into the flow line and be fully
mixed within seconds. Coefficient of friction of 0.01.
Glycerol Esters
Mazols
Drilling fluid Additive & Fracking Fluid Additive. MAZOL®
glycerol and polyglycerol esters have been developed to cover
the widest range of emulsification conditions. These esters are
excellent emulsifiers.
Guar Gum
Ricol-46
Drilling Fluid Additive Fracking Fluid Additive . Gelling agent
also thickens water in order to suspend sand in frac fluid, High
viscosity guar polymer suspended in a glycol ether base fluid.
Controls water loss and viscosity control in drilling fluids.
Hydrocarbon Fluids
D/F Fluid 17, D/F Fluid 21 and
D/F Fluid 33
Current range of high-purity, low-viscosity hydrocarbon fluids
that are superbly suitable for use in the drilling and fracking
of oil and gas wells. Colorless, odorless, non-toxic, and nonpolluting, they are high-performance replacements for diesel
fuel and other less-pure hydrocarbon solvents and oils. Our
D/F fluids are also BTEX-free (at limit of detection of 50 ppb),
inherently biodegradable, and conform to the highest purity
standards for food and pharmaceutical applications as white
mineral oils as defined in 21CFR 172.878.
Oilfield
2
Drilling (continued)
PRODUCT
TRADENAME
Lubricant for Drilling & Coiled
Tubing stage drillouts
PDS Super LW (winterized)
Drilling & Coiled Tubing Stage Drillouts (water and oil based
muds) PDS Super LW has the lowest coefficient of friction of
any lubricant on the market. It’s primary function is to provide
surface -to-surface lubricity, allowing one solid to slide by
another with ease providing exceptional well-bore stability, fluid
loss prevention, and rheology control. PDS Super L can be
customized to each application for optimal performance and
efficiency.
Modified Potatoe Starch
Emloc
Drilling, work over or completion high temperature fluid loss
control additive. Filtration control in all types of water base
drilling fluids ranging from fresh to salt saturated waters. Also
has shale inhibitive characteristics. It meets or exceeds API
13A specifications. Its thermal stability is up to 120C (248F).
Suggested dosage is 0.5-1%.
Oilfield Fibre
Arbocel grades
(LCM) Finely ground cellulosic material that controls loss
circulation and seepage losses in both water and oil-based
drilling fluids. Bridges cracks and plugs holes. Used in frac
sealing and plug/cake applications.
Organo Clay
BK 886B
Rheology/Viscosifier for drilling fluids (diesel and mineral based).
Organo Clay (tetraallkyl
ammonium bentonite) for
White Oil Systems
BK-192D
Hi gelling efficiency over low to medium polarity organic
fluids. Easy to incorporate and stable viscosity development.
Applicable to low temp systems. Typical applications in diesel
based oil drilling fluid, low aromatic hydrocarbon mineral oil
based oil drilling fluid, water in oil based oil drilling fluid.
Organo Clay for Diesel
Systems
BK-150D
High gelling efficiency over low to medium polarity organic liquids,
applicable to low temp systems.
Organo Clay for High temp
Diesel Systems
BK-192F
Viscocifier for any oil-based drilling fluid. Gels oil muds for longtime suspension of weighting agents in packer fluids and casing
packs. Stable at temp approaching 204°C.
Poly Acrylic Polymers and
Copolymers
Performol 23, 27, LHD
Synthetic Thickening agent for water based drilling fluids.
Achieves maximum shear-thinning viscosity and suspension
properties with high Temperature tolerances .
Polyethylene Glycol Esters
Mapeg
MAPEG® polyethylene glycol esters are mono- and di-esters of
various fatty acids. They offer graduated hydrophilic to lipophilic
surface active properties which make them useful as primary
and secondary emulsifiers with stability over a wide range of
formulating conditions.
Polymer Slurry RHEOLOGY
Modifier
XC Vis 5/10/20
Effective xanthan polymer slurry for use in either oil and gas
drilling or coiled tubing horizontal cleanouts. XC Vic polymer
blends are the economical choice for cleaning wellbores and
they are the fastest hydrating product on the market today.
SAPP (Sodium Acid
Pyrophosphate)
Sodium Acid Pyrophosphate
SAPP provides bore hole stability.
Sodium Citrate
Sodium Citrate Dihydrate
USP24
Drilling Fluids and Oil Sands . Rheology modifier. Chelating &
retarder, removal of heavy metals in oil sands.
Sorbitan Sesquioleate (SSO).
Tall oil fatty acid ester of
sorbitol
SSO
Oil Wetting Agent, Oil slick dispersant and Corrosion Inhibitor.
Derived from naturally renewable resources.
SorbitanFatty Acid Esters
S-Maz
Emulsifier, lubricant in Nonionic, lipophilic surfactants used to
prepare highly stable water in oil emulsions. When combined
with T Maz (ethoxylated sorbitan esters) S Maz is very desirable
as oil in water emulsifiers in drilling fluids.
Oilfield
3
Drilling (continued)
PRODUCT
TRADENAME
Starch
Cargill Gel 03420
Environmentally friendly rheology modification in water based
drilling, fluid mud.
Stearic Acid -saturated C18
Stearic Acid
Stearic acid is used in drilling fluids as a viscosifier and
defoamer.
Talc
IMERYS Talc
(Fluid Loss Additive) Rheology modifier to increase gel strengths
as well as viscosity.
Tall Oil Fatty Acid
Sylfat FA1, FA2
Emulsifiers and rheology modifiers in drilling fluid additive. Oil
based drilling fluid. Helps stabilize emulsions, reduces HPHT
filtration.
TKPP (Tetrapotassium
Pyrophosphate, Anhydrous)
Tetrapotassium
Pyrophosphate, Anhydrous
TKPP is a highly soluble, more environmentally friendly, low
sodium alternative to SAPP. Disperses/ deflocculates clay
mixtures in drilling muds.
Unbleached Lecithin
Yelkin TTS
Enhances emulsion, suspension and dispersion in oil based
drilling fluids/mud.
Water based Organoclay
Rheological Additive
BK 882
Provides good thixotropy and stability to give crude oil and
diesel systems good suspension property, wall protection and
anti-filtration.
Emulsifier
PRODUCT
TRADENAME
Biodegradable Surfactant
System
Stablec OFE
Promotes oil-wetting of solids and increases the resistance
to water contamination in oil-based muds. Improves flow
properties and helps coat surfaces of shale and other solids.
Natural Sodium Sulfonate
Petronate L
Strong emulsification properties. Molecular weight is 425.
Natural transparent, dark brown liquid readily soluble in
mineral oil.
Polyoxylethylene Alkyl Ether
Nonionic Surfactant
Emulgen line
NPE replacement. Emulsifier and wetting agent.
Fracturing
PRODUCT
TRADENAME
Aluminum Salt of
2-ethylhexoic acid
Calford G-810
Provides very strong gels in fracture oil wells which are based
on diesel fuel or similar solvents. Will gel diesel fuel sufficiently
quickly if fuel heated t approximately 70°C.
Aluminum Soap
Calford G-760
Complex soap designed to gel hydrocarbon and fracturing fluid
at room temperature. Gels solvents including gasoline, diesel
oil, varsol, xylene, benzene and mineral spirits.
Ammonium Chloride (NH4Cl)
Ammonium Chloride
Ammonium chloride liquid solution is an acidic brine that offers
many properties that serve to minimize or prevent formation
damage. They are shale inhibitive and compatible with most
formation water.
Breaker
Calford GB-452HF
Where downhole temp are not sufficient to effect complete
break (below 65°C) a companion chemical, Calford GB-452HF,
is available.
Oilfield
4
Fracturing (continued)
PRODUCT
TRADENAME
Ceramic spheres
Seal-N-Slide
Proppant - Application suited for shale sweeps. Effective in
lowering HTHP fluid loss and helps reduce seepage losses
while drilling. Alternative to calcium carbonate. Compressibility
strength of Seal-N-Slide makes it a great choice to be used
in systems that are being moved from well to well with no
reconditioning.
Defoamers, Siloxane
Foamblast
High viscosity, antifoam- silicone based, control of foam in
H2O based hydraulics, soluble oils and semisynthetic fluids.
Cementing sealer.
Distilled Tallow Fatty Acid
Voleic product range
Biodegradable emulsifier.
Friction Reducer & Proppant
Carrying Fluid
MM 200, 201, 300
Rapidly Hydrating Polymer for Frac . MM200 and MM201 (brine
version) is a combination friction reducer and viscosifier blend
that hydrates rapidly. Used for Fracturing and as FR for stage
plug drillout with stick or coil. MM 200 performs significantly
well compared to other polymers in cold frac water. Hydrates
in less than 10 seconds at 33°F while maintaining its proppant
carrying and friction reduction properties. MM 200 at higher
dosages (0.3-0.5%) will suspend sand. Therefore only one
chemical is required ...don’t have to switch from FR to Guar. In
hot wells, MM 200 & 201 remains stable at temperatures above
300°F. Both products can be broken with standard breakers.
Fumed Silicate
CAB-O-SIL TS 610
Used as a thixatrop thickening foaming fracking fluids to carry
proppants.
Glycerine
Glycerin 99.5%
Glycerin can be used as a component in completion fluids and
fracture fluids. Glycerin can be reacted to make polyglycerols
for drilling muds formulated for shale stabilization.
Glyoxal 40% / Ethandial
Glyoxal 40%
Glyoxal crosslinks polymers therefore increasing viscosity of
fracturing fluids.
Hydrating Polymers
Activator A
Viscosifier for problematic polymers . High performance
activator for building viscosity in following conditions: high
salt brines, crude / water oil, cold water, compromised slurry
design, compromised equipment with poor shear rate.
Hydrogenated Coconut Fatty
Acid
Hydrogenated Coconut Fatty
Acid
Biodegradable emulsifier.
Lactic acid
Lactic acid 88% Heat Stable
Can be used as a crosslinking agent for polymer gels. Removal
of carbonate or iron scale in oil equipment. High temperature
applications.
Low Viscosity oil
HY40
Fracturing Fluid. Suitable for wide range of application
temperatures.
Microemulsion, Enhanced
Flowback and Shale Stabilizer
RTN PLS X-15
Water-wetting version is presumed product of choice for the
Bakken and other EOG crude producing formations. Improves
flow through perforations where a water or emulsion block
is suspected. Benefits include increased fracture length by
improving pressure efficiency, improved conductivity (clean,
unobstructed fractures, speed cleanup and increased polymer
recovery. Rtn Pls X-15 successfully runs at lower dosages (0.25
gpt) still delivering water recoveries comparable to alternative
products at 0.2 % gpt. This product has an excellent clay
stabilizer as part of it’s makeup as well as an anti-foamer.
Oleic Acid
Oleic Acid
Oleic acid as its sodium salt is a major component of systems
as an emulsifying agent.
Oxyaluminum Octoate
OAO
Rheology modifier. Enhance rate of fluid gelation. Encapsulated
breaker for oil gels slick frac fluid.
Oilfield
5
Fracturing (continued)
PRODUCT
TRADENAME
Polyethylene glycol
Pluriols
PEG reduces the aggregates and nonomaterials (such as glass
beads, silica, iron) affinity for aggregation and improves their
transport through porous media.
Polysorbates-ethoxylated
sorbitan fatty acid ester
T-Maz
Dispersants, corrosion inhibitors. For oil in water and water in oil
emulsification needs, often used with S Maz. Used as stabilize
and dispersing agent.
Sodium Lactate 60% liquid
Arlac S
Can be used as a crosslinking agent for polymer gels. Removal
of carbonate or iron scale in oil equipment. High temperature
applications.
Sodium Xylene Sulfonate
Sodium Xylene Sulfonate
Anionic surfactant used as a solubilizer, coupling agent, viscosity
reducer. Offers good lubricity and heat resistance.
Sorbitan Fatty Acid Ester/
Sorbitan Monooleate (SMO)
S-MAZ 80K / SMO
Oil slick dispersant.
Wellbore Sweep Fluid
Maxim Sweep
Multifunctional Wellbore Sweep- Maxim Sweep is designed to
keep horizontal section clean, even under high temperatures.
Maxim allows for wellbore integrity by preventing shale
hydration caused by water movement into the rock, voids
and micropores. Maxim maintains the integrity of the cuttings,
allowing them to be removed by solids control equipment,
thus maintaining the quality and efficiency of the system. This
lubricant acts as an excellent corrosion inhibitor and oxygen
scavenger. If tripping or shutting a well for some time, Maxim
Sweep will keep barite suspended.
Industrial Cleaning
PRODUCT
TRADENAME
Green Wellbore Cleaning
Spacer
CleanVoc
Water-wetting product that dominates the interface. Prevents
hydrocarbons from depositing. Will remove sludges, including
barite, bentonite and residuals from oil based muds.
Laureth Carboxylic Acid
Akypo RLM 45CA
Akypo RLM100
Organic acid acts as a concentrated surfactant. Enables
formulations with various neutralization agents. Combined
benefit of non-ionic and anionic surfactants. Enhances
efficiency of Quats.
Miscellaneous
PRODUCT
TRADENAME
Dioctyl Sebacate
Monoplex DOS
Strip coating, film and sheeting for low temperatures Ester
type plasticizer, excellent viscosity stability, excellent at low
temperatures.
Propylene Glycol
Propylene Glycol Industrial
Grade
Used to reduce hydrate formation, typically ice formation
within gas streams during the processing of natural gas.
Drilling Fluid Testing used to test oil based drilling fluid by
breaking the emulsion.
Solvent borne adhesive
Thixon range
Vulcanized metal primer systems. Rubber to metal bonding
agents for stator components used in progressive cavity
pumping systems, valves and tanks.
Oilfield
6
Production
PRODUCT
TRADENAME
2-alkyl branched fatty alcohol
Farmin line
Primary and Tertiary amines,Vegetable and Tallow based primary
amines, Vegetable based Tertiary amines: C8 to C18 and C22
Alkyl Dimethyl Amines, selected Di Alkyl Methyl amines.
2-alkyl branched fatty alcohol
Kalcol line
Guerbet alcohols act as a co-solvent or coupling agent to
improve the solubility of highly polar substances in mineral
oil or improve the stability of dispersions/emulsions. Can be
used as a “green” winterizing agents (solvent) having very low
melting points compared with linear C20 and C24 counterparts
(respectively).
Broad Range Scale Control
Agent
LVL Scale 2920
Scale deposit control developed as a Calcium Carbonate and
Barium Sulphate scale inhibitor for use in high temperatures (to
250°F).
Calcium Carbonate Deposit
Control Agent
LVL Scale 2940
For severe potential calcium carbonate scale formation in
challenging environments (>250F pH, levels >9.0, Iron tolerant,
thermally stable). Ideal for H2S Scavenger applications in high
Calcium waters.
Calcium Chloride Powder 94%
Calcium Chloride Powder 94%
Calcium Chloride HT Powder 94 % has a wide variety of oilfield
uses; Salinity source in oil muds, flocculant for clear water
drilling, packer fluid, accelerator for oil well cement.
DDBSA, Sulphonic Acid Linear Alkylbenzene Sulfonic
Acid
DDBSA - Linear Alkylbenzene
Sulfonic Acid
DDBSA is an anionic surfactant. Used as antisludge additive/
emulsion breaker and paraffin dispersant. Is biodegradable and
environmentally friendly as it has a straight chain structure.
Dimerized fatty acids
Unidyme 60 & 60 Special,
Unidyme 35,18
Corrosion Inhibitor base.
Iron Control
LVL Iron Control 1806
Iron Control. Blend achieves a unique combination of Iron
fouling control as well as contributes to scale inhibition and
reducing corrosion in oilfield fluid systems. Prevents Iron
Sulphide and Iron Oxide deposits.
Laureth Carboxylic Acid
Akypo line
Oxidation-stable emulsifier based on ethercarboxylic acid.
Excellent emulsifier with good wetting properties. Hard Water
stability. Intensifies the corrosion protection in alkaline media.
Metal Foul & Scale Control
LVL 860D Metal Foul &Scale
Control
LVL 860D is a specialty solid product for oilfield systems where
Iron fouling and Corrosion are of primary concern. Inhibition
of Iron Oxide and Iron Sulphide deposits have been achieved
with treatment of LVL 860D, as well as substantially reduced
corrosion rates.
Multi-Functional Paraffin
Inhibitor
LVL Para 700
Designed difficult and challenging oilfield systems with severe
potential for paraffin formation.
Propargyl Alcohol
Propargyl Alcohol
Corrosion Inhibitor often used in stimulation formulations.
Scale and Metal Control
LVL 810D Scale and Metal
Control
LVL 810D is a specialty solid product for oil and gas wells where
Iron fouling and Corrosion are of primary concern. Inhibition
of Iron Oxide and Iron Sulphide deposits have been achieved
with treatment of LVL 810D, as well as substantially reduced
corrosion rates.
Scale/Corrosion Inhibitor
LVL 904D Scale/Corrosion
Inhibitor
LVL 904D - is a “slow-release” form of scale / corrosion
inhibitor developed for use in fracturing applications. It has
shown excellent product lifetime and effectiveness and can be
considered another method to deliver product for wells where
dosing liquids may not be ideal and minimal manual servicing is
desired.
Oilfield
7
Proudly representing our Principal Partners
in the Industrial Oils industry
LIMITED / LIMITÉE
www.lvlomas.com 800 575 3382
NATURAL-RESOURCES-OILFIELD-AUGUST-2014

Download Report