SK-ACP-E Two Door Panel Configuration Guide

SECURA KEY CARD ACCESS CONFIGURATION GUIDE
Single/Multi-Reader Systems with SK-ACPE Two-Door Panel
MULTI-PANEL SYSTEM USING SK-NETTM SOFTWARE- SINGLE LOCATION WITH LAN CONNECTION
NOTE: In this example, only the first panel is connected to the LAN. Additional panels are daisy-chained from the first panel using
RS-485 over twisted pair. SK-NET-MLD software must be used when connecting more than one SK-ACPE to the LAN. This diagram
can also be a remote location connected over a WAN, if a static IP address is used at each remote site.
¿
3
SK-ACPE
3
SK-ACPE
SK-ACPE
SK-ACPE
1
SK-ACPE
1
STAR /
FANOUT
DAISY CHAIN / MULTIDROP
3
“T”
CONFIG
¿
¿
NETWORK
1
SK-ACPE
SK-ACPE
SK-ACPE
RS-485 NETWORK CABLE:
SK-ACPE
RS-485 communications. Suggested cable: CAT 5
network cable or Two Twisted Pair. Total system cable
length: 4,000 ft.
SK-ACPE
STUBBED
SK-ACPE
ETHERNET CABLE:
Standard Ethernet cable connector connected to
existing LAN.
NOTE: Each SK-ACPE above can support 2 Wiegand output card readers.
SK-ACPE SYSTEM USING SK-NET-MLD SOFTWARE WITH MULTIPLE LAN CONNECTIONS
ROUTER/SWITCH
3
HUB
3
WIRED/WIRELESS
ROUTER
3
3
SK-ACPE
3
SK-ACPE
SK-ACPE
ETHERNET CABLE: (Required cables CAT 5e or CAT 6).
Wired: max distance 300’ (100m) between devices.
Wireless: Typically 100-200’ (30-60m) depending on interference, building structure and metal objects.
NOTE: Each SK-ACPE above can support 2 Wiegand Output Card Readers.
SK-ACPE
WITH OPTIONAL
SK-WLSE MOD*
MULTI LOCATION SYSTEM WITH SK-NET-MLD SOFTWARE
1
¿
SK-ACPE
RS-232
GATEWAY
1
USB
USB
SK-USB
SK-USB
SK-ACPE
¿
MODEM
NET-CONV-P
2
TELCO LINE
SK-ACPE
SK-ACPE
SK-ACPE
SK-MDM
SK-ACPE
1
Up to 100
SK-ACPE’s
A virtually unlimited number of remote locations
can be set-up on one PC with SK-NET-MLD Software.
Up to 100
SK-ACPE’s
RS-485 Network Wiring Connections
SK-ACPE
NOVA.16
J8
J2
Line A (2)
¿
Line B (1)
DC SIGNAL GROUND (3)
(REQUIRED)
¿
Earth Grounded Shield is highly
recommended in environments
to high
Earthsubject
Grounded
Shield voltage
is highlyelectrical
recommended
in environments
subject to
discharge
(i.e. lightning).
Shield
high voltage electrical discharge (i.e.
should
lightning).
Shield be
shouldconnected
be connected toto earth
earthground
ground only
at one
the cable.
only
at end
oneofend
of the cable.
DC Signal ground is required.
DC
DC
Signal
ground
is
required.
DC
Ground wire is NOT to be connected to
earthGround
ground. wire is NOT to be connected
to earth ground.
MULTI-PANEL SYSTEM USING SK-NETTM SOFTWARE- SINGLE LOCATION with RS-485 CONVERTER
NOTE: Use this configuration when the PC is located more than 100’ from the first SK-ACPE, and a LAN connection is not available.
NET-CONV-P
RS232-RS485 CONVERTER
PLUG INTO SK-USB
USB
SK-USB
¿
1
RS-485 NETWORK CABLE:
2
SERIAL CABLE:
1
UP TO 4000 Ft.
RS-485 communications. Suggested cable: CAT 5
network cable or Two Twisted Pair. Total system cable
length: 4,000 ft.
RS-232 communications. Suggested cable:
6-Conductor, Shielded, with no twisted pairs. Total
cable length 100 feet.
1
SK-ACPE
SK-ACPE
SK-ACPE
SK-ACPE
NOTE: When using the RS-232 to RS-485 converter, you cannot
use the stubbed, star fanout or “T” configuration. All network
connections from SK-ACPE to the next SK-ACPE must be in parallel
with each other. The J8 connector, Pins 1 and 2 must be a twisted
pair. Pin 3 (Ground) can use 1 conductor of a second pair.
SK-ACPE PANEL SYSTEM USING SK-NETTM SOFTWARE
WITH RS-232 GATEWAY CONNECTED DIRECTLY TO A PC
UP TO 500 Ft.
4
RS-232 GATEWAY
USB
DB9
¿
SK-USB SK-PLUG9
2
CARD READER WITH ANY
C A R D T E C H N O L O G Y,
WIEGAND OUTPUT, 26 BITS
RS-232
UP TO 100 Ft.
SK-ACPE
SK-ACPE PANEL SYSTEM USING SK-NETTM SOFTWARE
WITH RS-232 TO RS-485 CONVERTER (NET-CONV-P)
UP TO 500 Ft.
NET-CONV-P
RS232-RS485 CONVERTER
PLUG INTO SK-USB
4
1
¿
RS-485
UP TO 4000 Ft.
SK-USB
CARD READER WITH ANY
C A R D T E C H N O L O G Y,
WIEGAND OUTPUT, 26 BITS
SK-ACPE
¿
MULTI-PANEL SYSTEM USING SK-NETTM SOFTWARE- SINGLE LOCATION RS-232 CONNECTION
DAISY CHAIN / MULTIDROP
¿
SK-USB
DB9
SK-PLUG9
2
UP TO 100 Ft.
SK-ACPE
SK-ACPE
1
SK-ACPE
SK-ACPE
SK-ACPE
¿
USB
“T”
CONFIG
STAR /
FANOUT
SK-ACPE
SK-ACPE
SK-ACPE
SK-ACPE
SK-ACPE
STUBBED
SK-ACPE
NOTE: Each SK-ACPE above can support 2 Wiegand output card readers.
1
RS-45 NETWORK CABLE:
2
SERIAL CABLE:
4
WIEGAND CABLE:
RS-485 communications. Suggested cable: CAT 5
network cable or Two Twisted Pair. Total system cable
length: 4,000 ft.
For RS-232 communications interface. Suggested cable:
6-Conductor, Shielded, with no twisted pairs. Total cable
length 100 feet. SK-USB required if your PC does not
have a COM port
Suggested cable: 6-Conductor, Shielded, with no twisted
pairs. Total cable length 500 feet.
1
SYSTEM equipment components
ACCESS CONTROL UNIT:
SK-ACPE: Two Door Access Control Unit
Radio Key® Low Frequency Proximity
READERS:
RK-WM: Proximity Reader (2 readers per SK-ACPE), Mullion
RK-WS: Proximity Reader (2 readers per SK-ACPE), Switchplate
RK-WL: Proximity Reader (2 readers per SK-ACPE), Long Range
CARDS/TAGS:
RKCM-02-2 RKKT-02-2 RKCI-02-2 Molded Proximity Cards - 26/32 bit encoding
Key Tags - 26/32 bit encoding
ISO Proximity Cards - 26/32 bit encoding
E*Tag® High Frequency Proximity:
READERS:
ET4-WXM: 13.56 MHz ISO 15693, Mullion
ET4-WXS: 13.56 MHz ISO 15693, Switchplate
ET8-RO-W-D: 13.56 MHz ISO 15693, Switchplate
ET8-RO-W-M: 13.56 MHz ISO 15693, Mullion
CARDS/TAGS:
ETCI04-1- ISO Card- 26/32 bit encoding
ETCI04-4- ISO Card- 26/32 bit encoding, Mag-Stripe
ETST03-1-Key Tag Trapezoidal - 26/32 bit encoding
ETKT03-1 Key Tag, Rounded End, 26/32 bit encoding
PC REQUIREMENTS: See Table
MINIMUM REQUIREMENTS*
OPERATING SYSTEM
PROCESSOR
SPEED
RAM
AVAILABLE
DISK
SPACE
WINDOWS® XP OR
NEWER
1 GHz
1 GB
1 GB
* For larger installation more disk space may be required.
RECOMMENDED SYSTEM
WINDOWS® XP OR
NEWER
2 GHz
2 GB
10 GB
* For larger installation more disk space may be required.
SERVER REQUIREMENT (FOR CLIENT/SERVER VERSIONS)**
WINDOWS® 2003
OR NEWER
2 GHz
1 GB
1 GB
** For SK-NET-MLD-C/S version, a server is required to
install ADS and the database. SK-NET™ must be installed on a
workstation only.
Required Peripherals:
RS-232 COM Port, USB Port or TCP/IP,
a modem if you use dial-up and a printer for reports.
SOFTWARE:
SK-NET™- DM - Basic Software - USB Flash Drive and manual
SK-NET™ -MLD - Multi-Location Software with USB Flash Drive and manual
SK-NET-MLD - CSXX (XX= 2,5,10 or 15 workstations), USB Flash Drive & Manual with Client Server License
ACCESSORIES:
NET-CONV-P - RS-232 to RS-485 Converter with Power Supply (plug into SK-USB)
RS-232E - Connects J11 MTA connector to DB9
SK-24VDC - DC power supply, provides 1A@24VDC.
SK-MDM - Modem - 56K Baud External Modem for dial-up connection to any SK-ACPE with MLD software
SK-ACP-PS - 1A, 24VDC 4.0 AH supply and stand by battery for SK-ACPE.
SK-BAT - 4.0 AH standby battery for SK-ACPE.
SK-PLUG9 - Computer connector (DB9) with wire pigtail.
SK-USB - Converts USB Port at PC to serial COM Port with DB9 connector
SK-WLSE-MOD* - Wireless LAN adapter, 802.11 b/g. Powered by SK-ACPE. Connect at J12 and set jumpers.
SK-XFRMR - 16.5VAC 40VA Transformer for SK-ACPE.
* Contact Factory for Availability.
SECURA KEY sk-acpE
Typical Door Installation
2
2
INPUT 1-2
INPUT 2-1
2
INPUT 2-2
3
INPUT 1-1
DOOR MONITOR
READER
INPUT 2
1
RELAY 2-1
2
REMOTE
DOOROPEN
SWITCH
}
TO
2ND DOOR
READER
INPUT 1
TO PC HOST.
3
¿
3
L
A
T
C
H
BATTERY
BACK-UP
¿
1
1
1
ELECTRIC
STRIKE or
MAG LOCK
RS-485 TO
ADDITIONAL
PANELS
4
SK-ACPE
RK-WM
5
4
POWER
1
XFMR or
POWER
SUPPLY
PANEL
POWER
SUPPLY
POWER
STRIKE OR
MAGLOCK
SUPPLY
CABLE TYPES:
8060
1
2 COND, UNSHIELDED 16-18 AWG
2
2 COND, SHIELDED 18-24 AWG
3
6 COND, SHIELDED, NO TWISTED PAIRS 18-24 AWG WIEGAND OR RS-232
4
RS-485 - CAT 5 Network cable OR TWO Twisted Pair
5
TCP/IP - CAT 5e or CAT 6 ETHERNET CABLE
20301 NORDHOFF STREET
CHATSWORTH, CA 91311
PHONE (818) 882-0020 • FAX (818) 882-7052
TOLL FREE (800) 891-0020
[email protected] • www.securakey.com

Download Report