general - Toshiba FYI Portal

I. GENERAL
I-1. GENERAL
1-1. SYSTEM CONFIGURATION
1-2. SERVICE JIG
This section describes the outline of e-STUDIO2050C/2550C/2051C/2551C.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
1
I. GENERAL
I. GENERAL
■ The e-STUDIO2050C/2051C/2550C/2551C is a fullcolor digital MFP based on the concept of “Comfort, User
Friendliness and Compact Size”. It provides a network
function to use various office equipment in a
comprehensive manner, as well as printing and scanning
functions.
Copy speed for each model is as follows:
Full-color (cpm)
e-STUDIO2050C/2051C
20
e-STUDIO2550C/2551C
25
* The above status is available when the RADF is not used, and continuous copying
is performed in a landscape orientation with A-4 sized paper for the non-sort and
simplex copy modes.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
2
I. GENERAL
I. GENERAL
■ A color touch panel has been adopted for a further improvement in operability
and workability.
e-STUDIO2050C/2550C: 9-inch
e-STUDIO2051C/2551C: 7.5-inch
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
3
I. GENERAL
I. GENERAL
■ One drawer is provided in the
e-STUDIO2050C/2051C/2550C/2551C as a standard.
■ The destinations of the e-STUDIO are as follows.
The specification of the voltage is different for each destination.
NAD: North America
MJD: Europe
AUD: Australia
ASD: Asia and Turkey
CND: China
TWD: Taiwan
ARD: Argentine
SAD: Saudi Arabia
JPC: Japan
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
4
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆The system configuration is as follows.
A bypass feed unit, whose stack capacity is 100
sheets* at a maximum, is equipped as a standard.
*Stack height: 11 mm (equivalent to 100 sheets: 80
g/m2)
* No pickup roller is installed in this unit. Paper on
the bypass tray becomes ready to be fed when the
holding lever goes down to the paper setting side
(equipment side).
* This unit supports envelopes, postcards and tab
paper.
The stackless type Automatic Duplexing Unit (ADU)
is also equipped as a standard.
* e-STUDIO2050C/2550C only
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
5
I. GENERAL
I-1. SYSTEM CONFIGURATION
The pocket for the Operator’s Manual is also
equipped as a standard.
* Only for Japan
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
6
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ OPTIONS
The following devices are provided as options.
e-STUDIO2050C/2550C
MR-3024
MJ-1037
MJ-6008
KA-1640PC
MJ-5004
KK-4550
KN-2550
GH-1080※
MJ-1033
MJ-6007
KD-1040
Only for Japan
KD-2015J
KD-1032
MY-1039
KD-1031
・RADF: MR-3024
・Original Cover: KA-1640PC
・Work Table: KK-4550
・Paper Feed Controller: GH-1080
※For installing the PFU, PFP, LCF,
Inner Finisher and 1K Finisher
・Paper Feed Unit (PFU): MY-1040
・Paper Feed Pedestal (PFP) KD-1032
・Large Capacity Feeder (LCF): KD-1031
・Desk: MH-2050
・Bridge Kit: KN-2550
・Saddle Stitch Finisher: MJ-1037
・Hole Punch Unit: MJ-6008
・Inner Finisher: MJ-1036
・Hole Punch Unit: MJ-6007
・Job Separator: MJ-5004
MH-2050
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
7
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ OPTIONS
The following devices are provided as options.
・RADF: MR-3024
・Original Cover: KA-1640PC
・Work Table: KK-4550
・Paper Feed Controller: GH-1080
e-STUDIO2051C/2551C
MR-3024
KA-1640PC
KK-4550
MJ-5004
MJ-1033
MJ-6007
MD-0105/C
GH-1080※
KD-1040
KD-1032
※For installing the PFU, PFP, LCF,
Inner Finisher and 1K Finisher
・Paper Feed Unit (PFU): MY-1040
・Paper Feed Pedestal (PFP) KD-1032
・ Auto Duplex Unit: MD-0105/C
・Desk: MH-2050
・Bridge Kit: KN-2550
・Inner Finisher: MJ-1036
・Hole Punch Unit: MJ-6007
・Job Separator: MJ-5004
MH-2050
MY-1039
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
8
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ REVERSING AUTOMATIC DOCUMENT FEEDER
(RADF): MR-3024
The MR-3024 Reversing Automatic Document Feeder
(RADF), whose original capacity is 100 sheets* at
maximum, is provided.
* 80 g/m2 or 20 lbs.
■ ORIGINAL COVER: KA-1640PC
When no RADF is installed, attach the KA-1640PC
Original Cover*.
* KA-1640PC: for all destinations except China
KA-1640PC-C: for China
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
9
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ PAPER FEED CONTROLLER (PFC): GH-1080
This is an interface board to control the paper handling
options.
It is required when the PFU, PFP, LCF, Inner Finisher
and 1K Finisher are to be used.
■ PAPER FEED UNIT (PFU): MY-1040
One drawer can be added by installing the MY-1040
Paper Feed Unit (PFU).
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
10
I. GENERAL
I-1. SYSTEM CONFIGURATION
■PAPER FEED PEDESTAL (PFP): KD-1032
(for overseas)
One drawer can be added by installing the KD-1032
Paper Feed Pedestal (PFP).
* This is installable only when the PFU is equipped.
■ DRAWER MODULE: MY-1039 (for oversea)
One drawer can be added by installing the MY-1039
Drawer Module.
■ LARGE CAPACITY FEEDER (LCF): KD-1031
It allows paper to be placed in two rows side by side.
Paper on the other side is automatically slid to the
paper feed position for continuous feeding when one
side runs out.
* This is installable only when the PFU is equipped.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
11
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ INNER TRAY: MJ-5004
It can be installed inside the e-STUDIO. Copied,
printed or received fax paper is output by having it
distributed to the upper or lower tray, correspondingly.
Received fax paper exits to the upper tray and copied
or printed sheets to the lower one.
■ BRIDGE KIT: KN-2550
This kit is necessary for the installation of the 1K
Finisher.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
12
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ SADDLE STITCH FINISHER: MJ-1037
It supports multi-position stapling and saddle stitch
functions in 1-tray.
■ HOLE PUNCH UNIT: MJ-6008
It is possible to upgrade MJ-1037 to include the hole
punch function by installing the MJ-6008 Hole Punch
Unit.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
13
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ INNER FINISHER: MJ-1036
This compact 2-tray Multi-Position Stapler Finisher can
be installed in the inner tray.
■ HOLE PUNCH UNIT: MJ-6007
It is possible to upgrade MJ-1036 to include a hole
punch function by installing the MJ-6007 Hole Punch
Unit.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
14
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ WORK TABLE: KK-4550
This is provided for the temporary placing of originals
during copying jobs.
■ ACCESSIBLE ARM: KK-2550
It is an optional toll for a user in a wheelchair.
It is possible to close the RADF easily using this arm.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
15
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ OTHER OPTIONS
■ OPERATOR’S MANUAL POCKET
KK-1660: for all destinations except China
KK-1660C: for China
* For Japan, it is equipped as a standard.
■ DAMP HEATER KIT: MF-2050U/E
The MF-2050U/E Damp Heater Kit is provided as an
option for North America and Europe.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
16
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ HARNESS KIT FOR CARD CONTROLLER
:GQ-1250
■ HARNESS KIT FOR COIN CONTROLLER
: GQ-1260
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
17
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ SYSTEM OPTIOS
■ FAX UNIT: GD-1320
The e-STUDIO can be upgraded to the Super G3
facsimile by installing the GD-1320 Fax Unit*.
GD-1320NA: North America
GD-1320EU: Europe
GD-1320AU: Australia
GD-1320AS: Asia and other destinations
GD-1320C: China
GD-1320TW: Taiwan
GD-1320J: Japan
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
18
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ 2ND LINE FOR FAX UNIT: GD-1260
Installing the GD-1260 2nd Line for Fax Unit provides
two lines in total: one is for the fax transmission and
the other is for the fax reception. This speeds up fax
transmission and reception of large-volume
documents.
GD-1260NA-F: North America and Saudi Arabia
GD-1260EU-F: Europe
GD-1260AUS-F: Australia
GD-1260AU-F: Asia and other destinations
GD-1260C: China
GD-1260TW: Taiwan
GD-1260J-F: Japan
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
19
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ WIRELESS LAN MODULE: GN-1060
The GN-1060 Wireless LAN Module is also provided
for a network system extension.
It facilitates wireless connection of such as a notebook
PC to the e-STUDIO for network printing or the e-filing
box function.
■ ANTENNA: GN-3010
The GN-3010 Antenna is for the Wireless LAN Module
and Bluetooth Module.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
20
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ HDD: GE-1220
By installing this device, functions can be added or
expanded, such as in copying, printing, scanning, filing
and the optional faxing operation, and various use
statuses can be supported.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
21
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ ENABLERS
The following enables are provided as a system
option.
GP-1070: Data Overwrite Enabler
GP-1080: IP Sec Enable
GS-1010: Meta Scan Enabler
GS-1020: External Interface Enabler
GS-1007: Unicode Font Enabler
GP-1190A: Hardcopy Security Kit
* These enablers are used only once. After the
data are installed in the e-STUDIO, the enabler
cannot be used for any other MFP.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
22
I. GENERAL
I-1. SYSTEM CONFIGURATION
■ e-BRIDGE ID GATE
KP-2004 (HID): only for overseas
KP-2005 (MIFARE): only for overseas
■ e-BRIDGE ID GATE
KP-2006 (Felica/MIFARE): only for Japan
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
23
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ SUPPLY
The supplies for e-STUDIO2050C/2550C are as shown below.
■ DRUM: PS-ODFC30
■ TONER CARTRIDGE:
PS-ZTFC30-Y/M/C/K
■ DEVELOPER MATERIAL:
PS-ZDFC30-Y/M/C/K
■ WASTE TONER BOX: PS-TBFC30
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
24
I. GENERAL
I-1. SYSTEM CONFIGURATION
◆ REPLACEMENT UNIT
The replacement units for the e-STUDIO are as shown below.
DEVELOPER UNIT
FUSER UNIT
DRUM CLEANER UNIT
TRANSFER BELT
TRANSFER BELT CLEANING UNIT
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
25
I. GENERAL
I-2. SERVICE JIG
This section describes the service jigs for e-STUDIO2050C/2550C.
■ DOOR-SWITCH JIG
(JIG-SW-FCOV-H21X 6LJ71600000)
This door-switch jig is used for servicing and adjustment.
■ DEVELOPER MATERIAL NOZZLE
(NOZZLE-BOTTLE)
The developer unit can be filled with developer material by
using this nozzle.
■ NON-CONTACT THERMISTOR / THERMOSTAT GAP
JIG (JIG-FUS-TH-WH 6LJ58120000)
This jig is used for adjusting the gaps between the
thermistor and the thermostat of the fuser unit.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
26
I. GENERAL
I-2. SERVICE JIG
■ HARNESS HOLDING JIG
(JIG-GUIDE-HRNS-COVER 6LJ54689000)
This jig is used for binding up the harnesses when the
LED unit is replaced.
■ WIRE HOLDER JIG
(HOLDER-WIRE-PLY-H21X 6LJ59768000)
This jig allows the smooth installation of the carriage wire.
■ BELT TENSION JIG (SPE-MOT-TNS)
This jig is used for adjusting the belt tension when the
scan motor is replaced.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
27
I. GENERAL
I-2. SERVICE JIG
■ USB MEDIA DOWNLOAD JIG
This jig is used for copying the firmware data directly from
the PC and download it to the e-STUDIO.
■ DOWNLOAD JIG (PWA-DWNLD-JIG1/1F(16MB))
This jig is used for writing the firmware into the SYS board.
■ DOWNLOAD JIG (PWA-DWNLD-JIG2/2F(48MB))
This jig is used for writing the firmware into the SYS board.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
28
I. GENERAL
I-2. SERVICE JIG
■ DOWNLOAD JIG (K-PWA-DLM-320/F)
This jig is used for writing the firmware into the LGC
board, PLG board, SLG board, FAX board RADF board
and finisher control PC board.
■ ROM WRITER ADAPTER
(PWA-DL-ADP-350-1881/1931)
Two types of the ROM write adapters are provided. Use
either of them according to the ROM writer model which
you want to use.
■ PATTING POWDER (P-POWDER-PPT001)
This patting powder is used when the transfer belt or the
transfer belt cleaning unit is replaced.
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
29
I. GENERAL
Main Menu
© TOSHIBA TEC CORPORATION 2012 All Rights Reserved.
30

Download Report