RPM 1/4/8 Remote Zone Paging Microphone (RPM with

TM
(RPM with Hd9 Plug)
PENTON
RPM 1/4/8 Remote Zone Paging Microphone
1. RPM series Zone Paging Microphone is a digital device used
for volume and program control on PDM Zone Paging System.
2.Features :
a. Condenser microphone capsule with 0.775 v output max..
b. Frequency response at 20~20,000 Hz, Omni-directional.
c .Push to talk & Lock to talk switchable.
d. Zone busy with priority level indication.
3. Rear view of desk base..
This Cable Includes 12 leads with HD9 (15 Pin) for ;
1. 24VDC Power Supply
2. Balanced Audio Signal Output from Microphone
3. Rs485 Control Signal for Zone Display and Priority
Sensitivity Trimmer for Mic
Power Switch
4.Intallations:
a. Set RPM operated as MASTER or SALVE via the switch on the bottom of base.
b. If RPM operated as MASTER, Set unique ID via two(2) decimal rotary switches within 01~31.
Do not repeat ID with another MASTER RPM and even any RPC or RVC.
c. If RPM operated as SLAVE, Set unique ID from 01~31. Do not repeat within group for same
MASTER RPM.
5
9 0 1
78
78
78
78
6
6
78
78
6
ID at
13
9 0 1
6
5
6
9 0 1
5
2 3 4
6
ID at
01
5
2 3 4
9 0 1
2 3 4
5
2 3 4
9 0 1
2 3 4
5
2 3 4
9 0 1
Examples:
ID at
31
c. Set RPM audio output to PDM808 audio input via dip switch, example showed below:,
Salve RPM should be set same as Master RPM at this part.
ON
.
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
When RPM Audio output
connected to PDM808 INPUT 1
When RPM Audio output
connected to PDM808 INPUT 2
When RPM Audio output
connected to PDM808 INPUT 3
When RPM Audio output
connected to PDM808 INPUT 4
ON
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
When RPM Audio output
connected to PDM808 INPUT 5
When RPM Audio output
connected to PDM808 INPUT 6
When RPM Audio output
connected to PDM808 INPUT 7
When RPM Audio output
connected to PDM808 INPUT 8
If this RPM used as Master
(see connection next page)
If this RPM used as Slave
6
-Void-( For future Purpose)
5
78
9 0 1
5
ID
SETTING
2 3 4
1 2 3 4
2 3 4
9 0 1
78
ON
6
set this pin normally to off position.
(only special required)
set push to talk or lock and talk as you like
ON
1 2 3 4
If this is a RPM4 (4 zone), please set
Zone 1~4 (at OFF position) or Zone
5~8 (at ON position).
Audio input channel setting for RPM
connected on the PDM matrix mixer.
5. Priority: The priority level between Master RPM paging microphone is set via PC software.
The connection as above, Master RPM always has higher priority level to override Salve RPM.
Between Salves' RPM Microphones have equal priority level, operated as " First-come, First-served".
TM
PDM808 CONNECTION WITH RPM,RVC and RPC
POWER
SW1
SW2
SW3
SW4
SW5
SW6
SW7
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
SW8
1
2
0dB
-25dB
-55dB
SET ONE DOWN ONLY
88~130V
or
172~260V
AC
2
1
3
2
1
4
3
INPUT SENSITIVITY
2
SELECTOR 2
5
PHANTOM POWER
24VDC
2
48VDC
1
2
1
2
1
2
1
3
3
3
3
3
3
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
R
2
R
1
3
L
INPUT1
1
2
3
4
5
6
7
8
FAULT
1
2
3
4
5
6
7
8
+ 24 -
RS-485
RS-232
RS232
VDC
RELAY
CONTACT
SET ONE DOWN ONLY
1
DTC52
1 2 3 4 5
SELECTOR 1
DIP SWITCH (SW1 - SW8)
FAULT
CONTACT
REMOTE CONTACT
ON
OFF
OUTPUT
+CH5-
+CH6-
+CH7-
+CH8-
G
G
G
G
G
G
G
G
+CH1-
+CH2-
+CH3-
+CH4-
CHANNEL
L
RCA
INPUT8
RCA
RVC8
Contol Signal to
PDM808 RS-485 Port
Audio Signal to PDM808 Input
Slave RPM
Paging Microphone
Slave RPM
Paging Microphone
PENTON
RVC8
RVC8
RPC8
RJ45
1 to 2 Splitter
PDM808 & READY
LEDs ON
PDM808 & READY
LEDs ON
Master RPM
Paging Microphone
Master RPM
Paging Microphone
EXT. & READY
LEDs ON
**External 24VDC
Power Supply
Slave RPM
Paging Microphone
LOCAL & READY
LEDs ON
EXT.
: Extended from last Junction Box
PDM808 : Power Supplied from PDM808
LOCAL : Power Supplied from Local (External)
Up to 30 Slave RPM
Paging Microphone Totally
**When Many of RPM used, System power supply from PDM808 may be not enough. Open Junction Box to switch the power source
from external power supply but always remember it must be 24Vdc.

Download Report