Product Data Sheet Edition 2014-01_1 ® Sarnabar Sarnabar® Construction Fastening Profile for Sarnabar® System and Perimeter Fixation Product Description Folded fastening profile hot-dip coated steel for the mechanical fixation of waterproofing membranes. Uses Sarnabar is used for the mechanical fixation of waterproofing membranes on roofing structures and perimeter fixations. Characteristics / Advantages ® Light weight Resistance against common environmental influences Ease of application Recyclable Tests Approvals / Standards Quality management system EN ISO 9001/14001 European Technical Approval ETA-08/0262 Factory Mutual Class No. 4470 Product Data Form Appearance Surface: smooth Packaging Ordered number of products is packaged on pallets. Storage ® Storage Conditions Sarnabar shall be stored in dry conditions. Shelf-Life Sarnabar does not expire during correct storage. ® Technical Data Material Basis Hot-dip coated steel FVZS250GD + AZ150BC, according to DIN EN 10346 and DIN EN 10143, WN 1.0242 Width 30 mm Thickness 1.5 mm Height 7.0 mm Mass per unit area 0.70 kg/m Corrosion resistance 15 cycles Kesternich test (concentration SFW 2.0 S in accordance with DIN 50018) acoording to ETAG 006 - D.3.1. Sarnabar ® 1/4 Punched holes Types Type Length Article No. Diameter 2250 mm (± 8) Spacing 110652 ® 6.5 mm Sarnabar 6 ® Sarnabar 6/10 ® Sarnabar 6/15 4500 mm (± 8) 110653 2250 mm (± 8) 110654 3000 mm (± 8) 123577 4500 mm (± 8) 110655 2250 mm (± 8) 401855 6.5 mm / 10 mm 25 mm (alternating) 6.5 mm / 15 mm (alternating) 4500 mm (± 8) ® 401856 ® All Sarnabar types are marked with Sarnabar every 250 mm (letters in 4 mm height and 22 mm length). Application ® Sarnabar is used for the mechanical fixation of waterproofing membranes on roofing structures and perimeter fixations. Sarnabar ® 2/4 System Information System Structure ® ® Compatible to all Sikaplan and Sarnafil waterproofing membranes. Application Conditions / Limits Temperature ® The use of the Sarnabar is limited to geographical locations with average monthly minimum temperatures of -50 °C. Permanent ambient temperature during use is limited to +50 °C. Installation Instructions Installation Method Installation method: ® Sarnabar needs to be installed in accordance with the Sika application manual and installation instructions. Notes on Installation / Limits Installation works to be carried out only by Sika instructed contractors for roofing. ® Temperature limits for the installation of the Sarnabar : Substrate temperature: Ambient temperature: -30 °C min. / +60 °C max. -20 °C min. / +60 °C max. Special measures may be compulsory for installation below +5 °C ambient temperature due to safety requirements in accordance with national regulations. Sarnabar ® 3/4 Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. Local Restrictions Please note that as a result of specific local regulations the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields. Ecology, Health and Safety Information A Safety Data Sheet following EC-Regulation 1907/2006, Article 31 is not needed to bring the product to the market, to transport or to use it. The product does not damage the environment when used as specified. Legal Notes Construction REACH European Community Regulation on chemicals and their safe use (REACH: EC 1907/2006) This product is an article within the meaning of Regulation (EC) No 1907/2006 (REACH). It contains no substances which are intended to be released from the article under normal or reasonably foreseeable conditions of use. Therefore, there are no registration requirements for substances in articles within the meaning of Article 7.1 of the Regulation. Based on our current knowledge, this product does not contain SVHC (substances of very high concern) from the candidate list published by the European Chemicals Agency in concentrations above 0.1 % (w/w). Protective Measures Local safety regulations must be observed. Transportation Class The product is not classified as hazardous good for transport. Disposal The material is recyclable. Disposal must be according to local regulations. Please contact your local Sika sales organisation for more information. Sika Kimia Sdn Bhd Lot 689 Nilai Industrial Estate 71800 Nilai, Negeri Sembilan DK MALAYSIA Phone: +606-7991762 Fax: +606-7991980 e-mail: [email protected] www.sika.com.my Sarnabar ® 4/4
© Copyright 2025 ExpyDoc
